Click to Center | Panasonic KX-HCM270 manual

Operating Instructions

Click to Center

When you click the certain point on the Single Camera screen, the point is centered on the image.

1.Put the cursor on the point which should be centered and click it.

Cursor

2.The clicked point is centered.

Note

Click to Center does not move over the end of corner when the Pan/Tilt range reaches the end. The Pan/Tilt operation can be locked by Pan/Tilt control on page 82.

[For assistance, please call: 1-800-272-7033]

45

Image 45

Panasonic KX-HCM270 operating instructions Click to Center

Contents

Network Camera For operation assistance Call Introduction Trademarks Network Camera MemoFor assistance, please call Important Safety Instructions Table of Contents Specifications and Troubleshooting 111 Technical GuidesIndex 133 Section Getting to Know Network Camera Main Features Update Firmware Multi-Client AccessAuthentication Multi-Camera Screen System Requirements Authentication window Authentication-System Security Feature Setup CD-ROM 1 pc Rubber Cap 1 pc Included AccessoriesSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Lens Cover Indicator Camera Feature LocationsFront View Fixed Focus Lens Bottom View Rear View Network Camera Setup Installation Procedure Network Camera Configuration Type Network Camera can be installed on the LAN/IntranetType 2-Internet Connection with a Broadband Router Type 4-Direct Connection with a PC Type 3-Internet Direct Connection with a Modem How to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Default Network Camera Configuration TypeNetwork Parameters Table Type Port No Click OK to close IP Configuration window How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Wireless Setup To access Network windowTo set up the wireless network parameters Connection and Signal Strength status Set Infrastructure Default or AdHocChannel Encryption Key window Encryption Password window Wireless Settings Default Key If Top Page does not appear Port Forwarding IP Masquerade feature Network Camera Access from the Internet Top Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Single Camera Motion JpegMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Clicking Start Capture ViewerPrimary Secondary Multi-Camera Screen Setup Setup Go to Top AdministratorName/Time Security Reset to Factory Indicator ControlExternal Output Control Go to Top Network Enter only the number Instructions for the data fields Check Dhcp Dynamic Host Configuration Protocol If you use Network Camera on the LAN, set upHost Name When your ISP uses the Dhcp server function which Or administrator for the Host name File size of the image Camera Name/TimeName Date Time Changed AM/PM or 24H AdjustmentAuto Time Zone Security Administrator Refer to page 65 for details about authentication securityClick Security Administrator on Setup Administrator and General User Authentication window EnableFor Setup Password Retype Security General User Click Security General User on Setup Operating Instructions Top View Image Instructions for the data fields Top ResolutionImage 160 x Image Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm Mode Active Time of Trigger Alarm enable condition Login timing Data transfer method Over write setting Setting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer trigger Login timing Over write setting Instructions for the data fields White Balance Camera SetupFixed Indoor Fixed Suggested White Balance is also registered in preset programmingHaving reached the selected end Tilt Range Specifying the Pan/Tilt range Click Save when finished Multi-Camera IP Address or Enable check boxURL * 1 or Host Camera Name External Output Control Click External Output Control on Setup Indicator Control Status Click Cancel to quit. The window returns to Setup RestartClick Restart Now Update Firmware Click Update Firmware Click Update Firmware on Setup Open Reset to Factory Default Technical Guides Outdoor Installation Network Camera Installation High performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Cover the putties by rolling InchesDo not cover Ventilation hole 100 Network Camera Mounting Attach Network Camera to the tripod using the tripod boltFlexible Stand Mounting Tripod Mounting Wall Mounting Stand if necessaryWaterproof the rest of the cable Self Bonding tape 102 Ceiling Mounting Caulk around Flexible Stand if necessaryWaterproof the rest Cable For assistance, please call 103 Top Bottom Making holes on mortar wall Explanation of External I/O Interfacing to the External I/OPin Function External Sensor Input Circuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableSpace, , , #, &, %, =, +, ?, , and are not available 108 For assistance, please call 109 Displayable character set 110 Maintenance For assistance, please call 111 Specifications and Troubleshooting 112 Network Camera Reset Procedure-Default Settings For assistance, please call 113 Default Settings List 114 For assistance, please call 115 Items Factory Default Indispensable setting Value Alarm 116 Timer 117 Items Factory Default Indispensable setting Value Timer 118 Control Indicator Control Specifications Network Camera Specifications DescriptionOther Specification Description Message Transferring Method Weight 570 1.26 lb. Only the unitMm 3.46 inches Excluding the antenna and protruding objects Troubleshooting About Network Camera SetupProblem Cause and Remedy When Top Page does not appear, port number 80 might not be Proxy server may prevent you from connecting directly toWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, press For Indicator Control window Network window onTransfers older About Network Camera Setup Problem Cause and Remedy Refer to page 91 for the Update Firmware124 Lens About Top View Image screen About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical AdHoc GlossaryEncryption WEP Ieee 802.11b 132 133 Index Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 When you ship the product For product service