Setting explanation | Panasonic KX-HCM270 specification

Operating Instructions

Setting explanation

a.The active time of trigger is set between 9:00 AM to 6:00 PM from Monday to Friday.

When the alarm occurs in the setting time, the images are transferred to FTP server, and the notification is sent to the specified user via e- mail.

The alarm trigger is on when the sensor signal is changed to the [Rising] (GND to Open High) of External Sensor Input of External I/O.

b.The secondary time is set inactive.

c.The transferring image size is 160 x 120, and the image quality is standard.

d.Enables the Pre-alarm and Post-alarm Image Buffering:

Network Camera will transfer Pre-alarm 10 images by one image per minute and Post-alarm 20 images by one image per second when detecting the alarm trigger.

e.Setting of FTP server:

IP Address — 192.168.0.20 Port No. — 21

Login ID — Panasonic Password — ********

Login timing: Every Time

Upload File name — NetworkCamera

File name and time stamp is named to the file. (Example: NetworkCamera20030101093000000.jpg)

Underlined numbers are "9 h 30 min 00 s 000 ms on January 1, 2003". Data transfer method — Passive Mode

f.SMTP server address — xxx.xxx.com POP3 server address — xxx.xxx.com Login ID — Panasonic

Password — ********

Mail is sent to "NetworkCamera@xxx.xxx.com" from "Panasonic@xxx.xxx.com".

Subject is [Mail Transfer]. Text is [Alarm was generated].

[For assistance, please call: 1-800-272-7033]

77

Image 77

Panasonic KX-HCM270 operating instructions Setting explanation

Contents

Network Camera For operation assistance Call Introduction For assistance, please call TrademarksNetwork Camera Memo Important Safety Instructions Table of Contents Index 133 Specifications and Troubleshooting 111Technical Guides Section Getting to Know Network Camera Main Features Update Firmware Multi-Client AccessAuthentication Multi-Camera Screen System Requirements Authentication window Authentication-System Security Feature Setup CD-ROM 1 pc Rubber Cap 1 pc Included AccessoriesSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Lens Cover Indicator Camera Feature LocationsFront View Fixed Focus Lens Bottom View Rear View Network Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeNetwork Camera can be installed on the LAN/Intranet Type 4-Direct Connection with a PC Type 3-Internet Direct Connection with a Modem How to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Default Network Camera Configuration TypeNetwork Parameters Table Type Port No Click OK to close IP Configuration window How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display To set up the wireless network parameters Wireless SetupTo access Network window Channel Connection and Signal Strength statusSet Infrastructure Default or AdHoc Encryption Key window Encryption Password window Wireless Settings Default Key If Top Page does not appear Port Forwarding IP Masquerade feature Network Camera Access from the Internet Top Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Single Camera Motion JpegMulti-Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Clicking Start Capture ViewerPrimary Secondary Multi-Camera Screen Setup Setup Go to Top AdministratorName/Time Security Reset to Factory Indicator ControlExternal Output Control Go to Top Network Enter only the number Instructions for the data fields Check Dhcp Dynamic Host Configuration Protocol If you use Network Camera on the LAN, set upHost Name When your ISP uses the Dhcp server function which Or administrator for the Host name File size of the image Camera Name/TimeName Date Time Changed AM/PM or 24H AdjustmentAuto Time Zone Click Security Administrator on Setup Security AdministratorRefer to page 65 for details about authentication security Administrator and General User Authentication window EnableFor Setup Password Retype Security General User Click Security General User on Setup Operating Instructions Top View Image Instructions for the data fields Top ResolutionImage 160 x Image Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm Mode Active Time of Trigger Alarm enable condition Login timing Data transfer method Over write setting Setting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer trigger Login timing Over write setting Instructions for the data fields White Balance Camera SetupFixed Indoor Fixed Suggested White Balance is also registered in preset programmingHaving reached the selected end Tilt Range Specifying the Pan/Tilt range Click Save when finished Multi-Camera IP Address or Enable check boxURL * 1 or Host Camera Name External Output Control Click External Output Control on Setup Indicator Control Status Click Restart Now Click Cancel to quit. The window returns to SetupRestart Update Firmware Click Update Firmware Click Update Firmware on Setup Open Reset to Factory Default Technical Guides Outdoor Installation Network Camera Installation High performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Do not cover Ventilation hole 100 Cover the putties by rollingInches Network Camera Mounting Attach Network Camera to the tripod using the tripod boltFlexible Stand Mounting Tripod Mounting Waterproof the rest of the cable Self Bonding tape 102 Wall MountingStand if necessary Waterproof the rest Cable For assistance, please call 103 Ceiling MountingCaulk around Flexible Stand if necessary Top Bottom Making holes on mortar wall Explanation of External I/O Interfacing to the External I/OPin Function External Sensor Input Circuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableSpace, , , #, &, %, =, +, ?, , and are not available 108 For assistance, please call 109 Displayable character set 110 Maintenance For assistance, please call 111 Specifications and Troubleshooting 112 Network Camera Reset Procedure-Default Settings For assistance, please call 113 Default Settings List 114 For assistance, please call 115 Items Factory Default Indispensable setting Value Alarm 116 Timer 117 Items Factory Default Indispensable setting Value Timer 118 Control Indicator Control Other Specification Description SpecificationsNetwork Camera Specifications Description Message Transferring Method Weight 570 1.26 lb. Only the unitMm 3.46 inches Excluding the antenna and protruding objects Problem Cause and Remedy TroubleshootingAbout Network Camera Setup When Top Page does not appear, port number 80 might not be Proxy server may prevent you from connecting directly toWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, press Transfers older For Indicator Control windowNetwork window on 124 About Network Camera Setup Problem Cause and RemedyRefer to page 91 for the Update Firmware Lens About Top View Image screen About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical AdHoc GlossaryEncryption WEP Ieee 802.11b 132 133 Index Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 When you ship the product For product service