Manuals / Panasonic / Photography / Digital Camera

Panasonic KX-HCM270 operating instructions Simple Installation using the Setup CD-ROM

Models: KX-HCM270

1 138

Download 138 pages 58.85 Kb

Page 28

Operating Instructions

2.6Simple Installation using the Setup CD-ROM

After finishing cabling, turn on Network Camera and insert the Setup CD-ROM in the CD-ROM drive of the PC. Setup CD-ROM should start the application automatically. This program automatically finds Network Cameras on the network.

1.Turn on Network Camera.

2.Insert the Setup CD-ROM in the CD-ROM drive of the PC.

(If Network Camera Setup window does not appear, click "setup.exe" on the Setup CD-ROM.)

28

Image 28

Panasonic KX-HCM270 operating instructions Simple Installation using the Setup CD-ROM

Contents

Network Camera Introduction For operation assistance CallNetwork Camera Memo TrademarksFor assistance, please call Important Safety Instructions Table of Contents Technical Guides Specifications and Troubleshooting 111Index 133 Section Main Features Getting to Know Network CameraMulti-Client Access Update FirmwareAuthentication Multi-Camera ScreenSystem Requirements Authentication-System Security Feature Authentication windowIncluded Accessories Setup CD-ROM 1 pc Rubber Cap 1 pcSelf Bonding tape Connector Cover AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pcSetup CD-ROM Camera Feature Locations Lens Cover IndicatorFront View Fixed Focus LensRear View Bottom ViewNetwork Camera Setup Installation Procedure Network Camera can be installed on the LAN/Intranet Network Camera Configuration TypeType 2-Internet Connection with a Broadband Router Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCHow to turn on Network Camera for Installation Preparing the Network Parameters for Network Camera Network ParametersNetwork parameters memo for Network Camera Network Camera Configuration Type DefaultNetwork Parameters Table Type Port NoHow to refer the network parameters from the PC Click OK to close IP Configuration windowSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display To access Network window Wireless SetupTo set up the wireless network parameters Set Infrastructure Default or AdHoc Connection and Signal Strength statusChannel Encryption Password window Encryption Key windowDefault Key Wireless SettingsIf Top Page does not appear Network Camera Access from the Internet Port Forwarding IP Masquerade featureTop Network Camera Screen and Setup Window Network Camera Flow Chart Example TopHttp//Global IP address of Broadband RouterPortNo Top Motion Jpeg Single CameraMulti-Camera HelpActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click DeleteNon Transfer mode Alarm/Timer mode Viewing Buffered Image ScreenViewer Clicking Start CapturePrimary SecondaryMulti-Camera Screen Setup Setup Administrator Go to TopName/Time SecurityIndicator Control Reset to FactoryExternal Output ControlGo to Top Network Instructions for the data fields Enter only the numberIf you use Network Camera on the LAN, set up Check Dhcp Dynamic Host Configuration ProtocolHost Name When your ISP uses the Dhcp server function which Or administrator for the Host nameFile size of the image Name/Time CameraName DateAdjustment Time Changed AM/PM or 24HAuto Time ZoneRefer to page 65 for details about authentication security Security AdministratorClick Security Administrator on Setup Enable Administrator and General User Authentication windowFor Setup Password RetypeClick Security General User on Setup Security General UserOperating Instructions Top View Image Resolution Instructions for the data fields TopImage 160 xImage Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer windowAlarm enable condition Active Time of TriggerLogin timing Over write setting Data transfer methodSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the imageLogin timing Over write setting Camera Setup Instructions for the data fields White BalanceFixed Indoor FixedWhite Balance is also registered in preset programming SuggestedHaving reached the selected end Tilt RangeClick Save when finished Specifying the Pan/Tilt rangeMulti-Camera Enable check box IP Address orURL * 1 or Host Camera NameClick External Output Control on Setup External Output ControlIndicator Control Status Restart Click Cancel to quit. The window returns to SetupClick Restart Now Update Firmware Click Update Firmware on Setup Click Update FirmwareOpen Reset to Factory Default Technical Guides Network Camera Installation Outdoor InstallationHigh performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Inches Cover the putties by rollingDo not cover Ventilation hole 100 Attach Network Camera to the tripod using the tripod bolt Network Camera MountingFlexible Stand Mounting Tripod MountingStand if necessary Wall MountingWaterproof the rest of the cable Self Bonding tape 102 Caulk around Flexible Stand if necessary Ceiling MountingWaterproof the rest Cable For assistance, please call 103 Top Bottom Making holes on mortar wall Interfacing to the External I/O Explanation of External I/OPin Function External Sensor InputCircuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setSpace, , , #, &, %, =, +, ?, , and are not available 108Displayable character set For assistance, please call 109Maintenance 110Specifications and Troubleshooting For assistance, please call 111Network Camera Reset Procedure-Default Settings 112Default Settings List For assistance, please call 113114 Items Factory Default Indispensable setting Value Alarm For assistance, please call 115Timer 116Items Factory Default Indispensable setting Value Timer 117Control Indicator Control 118Network Camera Specifications Description SpecificationsOther Specification Description Weight 570 1.26 lb. Only the unit Message Transferring MethodMm 3.46 inches Excluding the antenna and protruding objectsAbout Network Camera Setup TroubleshootingProblem Cause and Remedy Proxy server may prevent you from connecting directly to When Top Page does not appear, port number 80 might not beWhen you use DDNS, you need to set Default Gateway If Top Page does not appear in the above procedure, pressNetwork window on For Indicator Control windowTransfers older Refer to page 91 for the Update Firmware About Network Camera Setup Problem Cause and Remedy124 About Top View Image screen LensView Image Setting window on About Other TroublesConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Glossary AdHocEncryption WEP Ieee 802.11b132 Index 133Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 For product service When you ship the product