Maintenance, 110 | Panasonic KX-HCM270 manual

Operating Instructions

4.4Maintenance

To keep Network Camera functioning in good condition, maintenance plays an important part. Keep maintenance when using Network Camera. After removing the sand or dust from the Lens Cover, wipe the Lens Cover with a dry cloth.

Fixed Focus Lens

•Do not touch the Lens Cover. Touching it may leave a fingerprint and can cause the image to be out of focus.

•Do not pour the water to wash the unit or the Lens Cover of Network Camera.

•Clean the Lens Cover with lens cleaning paper. Do not use the chemical matters like alcohol, soap, benzine, thinner, wax, petroleum, hot water, insecticide spray, glass cleaner and so on. They may bend the Connector Cover and the body of Network Camera.

Lens Cover	Lens cleaning
	paper

110

Image 110

Panasonic KX-HCM270 operating instructions Maintenance, 110

Contents

Network Camera Introduction For operation assistance Call For assistance, please call TrademarksNetwork Camera Memo Important Safety Instructions Table of Contents Index 133 Specifications and Troubleshooting 111Technical Guides Section Main Features Getting to Know Network Camera Authentication Multi-Client AccessUpdate Firmware Multi-Camera Screen System Requirements Authentication-System Security Feature Authentication window Self Bonding tape Connector Cover Included AccessoriesSetup CD-ROM 1 pc Rubber Cap 1 pc AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Setup CD-ROM Front View Camera Feature LocationsLens Cover Indicator Fixed Focus Lens Rear View Bottom View Network Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeNetwork Camera can be installed on the LAN/Intranet Type 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PC How to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Network Parameters Table Network Camera Configuration TypeDefault Type Port No How to refer the network parameters from the PC Click OK to close IP Configuration window Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display To set up the wireless network parameters Wireless SetupTo access Network window Channel Connection and Signal Strength statusSet Infrastructure Default or AdHoc Encryption Password window Encryption Key window Default Key Wireless Settings If Top Page does not appear Network Camera Access from the Internet Port Forwarding IP Masquerade feature Top Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Multi-Camera Motion JpegSingle Camera Help ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Deleting the preset buttons Click Delete Non Transfer mode Alarm/Timer mode Viewing Buffered Image Screen Primary ViewerClicking Start Capture Secondary Multi-Camera Screen Setup Setup Name/Time AdministratorGo to Top Security External Output Indicator ControlReset to Factory Control Go to Top Network Instructions for the data fields Enter only the number Host Name When your ISP uses the Dhcp server function which If you use Network Camera on the LAN, set upCheck Dhcp Dynamic Host Configuration Protocol Or administrator for the Host name File size of the image Name Name/TimeCamera Date Auto AdjustmentTime Changed AM/PM or 24H Time Zone Click Security Administrator on Setup Security AdministratorRefer to page 65 for details about authentication security For Setup Password EnableAdministrator and General User Authentication window Retype Click Security General User on Setup Security General User Operating Instructions Top View Image Image ResolutionInstructions for the data fields Top 160 x Image Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer window Alarm enable condition Active Time of Trigger Login timing Over write setting Data transfer method Setting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Image Frequency Sets the interval to send the image Login timing Over write setting Fixed Indoor Camera SetupInstructions for the data fields White Balance Fixed Having reached the selected end White Balance is also registered in preset programmingSuggested Tilt Range Click Save when finished Specifying the Pan/Tilt range Multi-Camera URL * 1 or Host Enable check boxIP Address or Camera Name Click External Output Control on Setup External Output Control Indicator Control Status Click Restart Now Click Cancel to quit. The window returns to SetupRestart Update Firmware Click Update Firmware on Setup Click Update Firmware Open Reset to Factory Default Technical Guides Network Camera Installation Outdoor Installation High performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Do not cover Ventilation hole 100 Cover the putties by rollingInches Flexible Stand Mounting Attach Network Camera to the tripod using the tripod boltNetwork Camera Mounting Tripod Mounting Waterproof the rest of the cable Self Bonding tape 102 Wall MountingStand if necessary Waterproof the rest Cable For assistance, please call 103 Ceiling MountingCaulk around Flexible Stand if necessary Top Bottom Making holes on mortar wall Pin Function Interfacing to the External I/OExplanation of External I/O External Sensor Input Circuit Diagram Example Space, , , #, &, %, =, +, ?, , and are not available Ascii and ISO-8859-1 Character TableUnavailable character set 108 Displayable character set For assistance, please call 109 Maintenance 110 Specifications and Troubleshooting For assistance, please call 111 Network Camera Reset Procedure-Default Settings 112 Default Settings List For assistance, please call 113 114 Items Factory Default Indispensable setting Value Alarm For assistance, please call 115 Timer 116 Items Factory Default Indispensable setting Value Timer 117 Control Indicator Control 118 Other Specification Description SpecificationsNetwork Camera Specifications Description Mm 3.46 inches Weight 570 1.26 lb. Only the unitMessage Transferring Method Excluding the antenna and protruding objects Problem Cause and Remedy TroubleshootingAbout Network Camera Setup When you use DDNS, you need to set Default Gateway Proxy server may prevent you from connecting directly toWhen Top Page does not appear, port number 80 might not be If Top Page does not appear in the above procedure, press Transfers older For Indicator Control windowNetwork window on 124 About Network Camera Setup Problem Cause and RemedyRefer to page 91 for the Update Firmware About Top View Image screen Lens View Image Setting window on About Other Troubles Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Encryption WEP GlossaryAdHoc Ieee 802.11b 132 Index 133 Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 For product service When you ship the product