Panasonic KX-HCM270 guide

Operating Instructions

2.Thread the AC adaptor cord through the hook. Put the Rubber Cap and the Connector Cover by fastening the three screws in numerical order. The remaining screw hole on the Connector Cover is used for attaching Sunshade.

Note

Be sure to thread the AC adaptor cord through the hook.

Carefully insert the		Connector Cover
Carefully insert the
Rubber Cap into the
hole, gently pressing
it into place using		1
the end of the		1
long tool.		3
	AC
	adaptor	2
	cord	2
	cord
	Hook

3.Attach the Sunshade by fastening the two screws.

[For assistance, please call: 1-800-272-7033]

99

Image 99

Panasonic KX-HCM270 operating instructions Be sure to thread the AC adaptor cord through the hook

Contents

Network Camera For operation assistance Call Introduction Trademarks Network Camera MemoFor assistance, please call Important Safety Instructions Table of Contents Specifications and Troubleshooting 111 Technical GuidesIndex 133 Section Getting to Know Network Camera Main Features Multi-Camera Screen Multi-Client AccessUpdate Firmware Authentication System Requirements Authentication window Authentication-System Security Feature AC Adaptor 1 pc Flexible Stand 1 pc Sunshade 1 pc Included AccessoriesSetup CD-ROM 1 pc Rubber Cap 1 pc Self Bonding tape Connector Cover Setup CD-ROM Fixed Focus Lens Camera Feature LocationsLens Cover Indicator Front View Bottom View Rear View Network Camera Setup Installation Procedure Network Camera Configuration Type Network Camera can be installed on the LAN/IntranetType 2-Internet Connection with a Broadband Router Type 4-Direct Connection with a PC Type 3-Internet Direct Connection with a Modem How to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Type Port No Network Camera Configuration TypeDefault Network Parameters Table Click OK to close IP Configuration window How to refer the network parameters from the PC Setting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Wireless Setup To access Network windowTo set up the wireless network parameters Connection and Signal Strength status Set Infrastructure Default or AdHocChannel Encryption Key window Encryption Password window Wireless Settings Default Key If Top Page does not appear Port Forwarding IP Masquerade feature Network Camera Access from the Internet Top Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Help Motion JpegSingle Camera Multi-Camera ActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttons Viewing Buffered Image Screen Non Transfer mode Alarm/Timer mode Secondary ViewerClicking Start Capture Primary Multi-Camera Screen Setup Setup Security AdministratorGo to Top Name/Time Control Indicator ControlReset to Factory External Output Go to Top Network Enter only the number Instructions for the data fields Or administrator for the Host name If you use Network Camera on the LAN, set upCheck Dhcp Dynamic Host Configuration Protocol Host Name When your ISP uses the Dhcp server function which File size of the image Date Name/TimeCamera Name Time Zone AdjustmentTime Changed AM/PM or 24H Auto Security Administrator Refer to page 65 for details about authentication securityClick Security Administrator on Setup Retype EnableAdministrator and General User Authentication window For Setup Password Security General User Click Security General User on Setup Operating Instructions Top View Image 160 x ResolutionInstructions for the data fields Top Image Image Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm Mode Active Time of Trigger Alarm enable condition Login timing Data transfer method Over write setting Setting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer trigger Login timing Over write setting Fixed Camera SetupInstructions for the data fields White Balance Fixed Indoor Tilt Range White Balance is also registered in preset programmingSuggested Having reached the selected end Specifying the Pan/Tilt range Click Save when finished Multi-Camera Camera Name Enable check boxIP Address or URL * 1 or Host External Output Control Click External Output Control on Setup Indicator Control Status Click Cancel to quit. The window returns to Setup RestartClick Restart Now Update Firmware Click Update Firmware Click Update Firmware on Setup Open Reset to Factory Default Technical Guides Outdoor Installation Network Camera Installation High performance for wireless communication Network Camera Cabling Be sure to thread the AC adaptor cord through the hook Cover the putties by rolling InchesDo not cover Ventilation hole 100 Tripod Mounting Attach Network Camera to the tripod using the tripod boltNetwork Camera Mounting Flexible Stand Mounting Wall Mounting Stand if necessaryWaterproof the rest of the cable Self Bonding tape 102 Ceiling Mounting Caulk around Flexible Stand if necessaryWaterproof the rest Cable For assistance, please call 103 Top Bottom Making holes on mortar wall External Sensor Input Interfacing to the External I/OExplanation of External I/O Pin Function Circuit Diagram Example 108 Ascii and ISO-8859-1 Character TableUnavailable character set Space, , , #, &, %, =, +, ?, , and are not available For assistance, please call 109 Displayable character set 110 Maintenance For assistance, please call 111 Specifications and Troubleshooting 112 Network Camera Reset Procedure-Default Settings For assistance, please call 113 Default Settings List 114 For assistance, please call 115 Items Factory Default Indispensable setting Value Alarm 116 Timer 117 Items Factory Default Indispensable setting Value Timer 118 Control Indicator Control Specifications Network Camera Specifications DescriptionOther Specification Description Excluding the antenna and protruding objects Weight 570 1.26 lb. Only the unitMessage Transferring Method Mm 3.46 inches Troubleshooting About Network Camera SetupProblem Cause and Remedy If Top Page does not appear in the above procedure, press Proxy server may prevent you from connecting directly toWhen Top Page does not appear, port number 80 might not be When you use DDNS, you need to set Default Gateway For Indicator Control window Network window onTransfers older About Network Camera Setup Problem Cause and Remedy Refer to page 91 for the Update Firmware124 Lens About Top View Image screen About Other Troubles View Image Setting window on Confirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Ieee 802.11b GlossaryAdHoc Encryption WEP 132 133 Index Operating Instructions TCP/IP Wireless Router 37 Wireless window 136 137 When you ship the product For product service