KX-P7100
7.9.IC11 ( Engine Control CPU )
IC11 (Engine Control CPU)
Pin | Symbol | In/Out | Function | |
No. | ||||
|
|
| ||
1 | UI2 | - | (not used) | |
2 | INT27 | In | Door open signal | |
3 | AN0 | In | Thermistor voltage detect | |
4 | P51 | In | TESEN | |
5 | P52 | Out | Scanner motor control signal | |
6 | P53 | Out | Fan motor control signal | |
7 | P54 | Out | Toner Empty LED control | |
|
|
| signal | |
8 | P55 | Out | Charger control signal | |
9 | P56 | Out | Dev. bias channel signal | |
10 | P57 | Out | Transfer bias control signal | |
11 | AVCC | - | +5V | |
12 | AVR | - | +5V | |
13 | AVSS | - | GND | |
14 | INT10 | In | Hsync signal | |
15 | P61 | In | Scanner motor lock signal | |
16 | INT12 | In | Top sennsor signal | |
17 | P63 | In | Process unit detection signal | |
18 | P64 | In | Fan motor error signal | |
19 | nRST | In | System reset | |
20 | MOD0 | - | GND | |
21 | MOD1 | - | GND | |
22 | X0 | In | System clock | |
23 | X1 | - | N.C. | |
24 | VSS | - | GND | |
25 | P27 | - | (not used) | |
26 | P26 | - | (not used) | |
27 | P25 | Out | EEPROM data out | |
28 | P24 | Out | EEPROM clock | |
29 | P23 | Out | EEPROM chip select | |
30 | PPGO2 | Out | Scanner motor clock | |
31 | PPGO1 | Out | Fuser contorl signal | |
32 | P20 | Out | +5V contorl signal | |
|
|
|
|
Pin | Symbol | In/Out | Function | |
No. | ||||
|
|
| ||
33 | P17 | In | EEPROM data in | |
34 | P16 | - | (not used) | |
35 | P15 | - | N.C. | |
36 | P14 | In | Resist seneor signal | |
37 | P13 | - | N.C. | |
38 | P12 | - | N.C. | |
39 | P11 | In | EEPROM initialize signal | |
40 | P10 | In | Exit sensor signal | |
41 | P07 | Out | Pick up control signal | |
42 | P06 | Out | Resist control signal | |
43 | P05 | Out | Exit control signal | |
44 | P04 | Out | Motor I0 control signal | |
45 | P03 | - | N.C. | |
46 | P02 | Out | Purge signal | |
47 | P01 | Out | Status busy signal | |
48 | P00 | Out | Top signal | |
49 | NC | - | GND | |
50 | P30 | Out | Printer ready signal | |
51 | SCK1 | In | Communication clock | |
52 | SO1 | Out | Status data signal | |
53 | SI1 | In | Command data signal | |
54 | PTO2 | Out | Dev. bias PWM signal | |
55 | P35 | In | Print signal | |
56 | VCC | - | +5V | |
57 | WTO | In | Command busy signal | |
58 | PTO1 | Out | Transfer bias PWM signal | |
59 | INT20 | In | Power save signal | |
60 | P41 | Out | Serial clock | |
61 | P42 | Out | Serial data out | |
62 | P43 | In | Serial data in | |
63 | P44 | Out | Chip select | |
64 | P45 | Out | Motor I1 control signal | |
|
|
|
|
7.10. IC12 ( EEPROM )
IC12 (EEPROM)
Pin | Symbol | In/Out | Function | |
No. | ||||
|
|
| ||
1 | CS | In | Chip Select Signal | |
2 | SK | In | Serial Clock | |
3 | DI | In | Data Input | |
4 | DO | Out | Data Output | |
5 | GND | - | GND | |
6 | TEST | - | Test terminal (not used) | |
7 | NC | - | N.C. | |
8 | VCC | - | +5 V | |
|
|
|
|
93
