Error messages, Display message | Panasonic KX-TG8162AL specification

Useful Information

Error messages

Display message

Base no power

or

No link to base. Reconnect main base AC adaptor.

or

No link.

Check Phone Line

Error

Failed

Incomplete

Memory Full

Use rechargeable battery.

You must first subscribe to Caller ID.

Cause/solution

RThe handset has lost communication with the base unit. Move closer to the base unit and try again.

RUnplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again.

RThe handset’s registration may have been cancelled. Re-register the handset (page 32).

RWhen “No link.” is displayed during a power failure, place a handset on the base unit to supply power to the base unit.

RThe supplied telephone line cord has not been connected yet or not connected properly. Check the connections (page 9).

RRecording was too short. Try again.

RPhonebook copy failed (page 22). Confirm the other handset (the receiver) is in standby mode and try again.

RThe receiver’s phonebook memory is full. Erase the unwanted phonebook entries from the other handset (the receiver) and try again.

RThe phonebook memory is full. Erase unwanted entries (page 22).

RMessage memory is full. Erase unwanted messages (page 38, 39).

RThe call barred list memory is full. Erase unwanted entries (page 31).

RA wrong type of battery such as Alkaline or Manganese was inserted. Use only the rechargeable Ni-MH batteries noted on page 4, 6.

RYou must subscribe to a Caller ID service. Once you receive caller information after subscribing to a Caller ID service, this message will not be displayed.

47

Image 47

Panasonic KX-TG8162AL, KX-TG8163AL operating instructions Error messages, Display message, Cause/solution

Contents

Thank you for purchasing a Panasonic product Digital Cordless Answering System Table of Contents Model composition Accessory informationSupplied accessories Model number Additional/replacement accessoriesAccessory item Expanding your phone system For your safety Ni-MH batteries AAA R03 size Important safety instructionsBattery General notices Other information SpecificationsFor best performance Operating conditions RF transmission powerFrequency range Charger Connections Setting upBattery installation Battery charging Operation Operating time Battery levelIcon Battery level Base unit ControlsHandset Line DisplayHandset display items Greeting Only is Handset main menu icons Screen saver modeBase unit display items Handset soft key icons Display language Turning the power on/offInitial settings Smart function key Top Key Setting the smart function key Top Key Setup One touch eco modeDisplay mode Using the smart function key Top Key Using soft key Temporarily switching the display mode Programming the display mode beforehand Answering calls Making calls Key lock Useful features during a call When only 1 handset is registered Power back-up operationMaking calls during a power failure Continuing a call during a power failure Finding and calling from a phonebook entry Handset phonebookAdding entries Categories Speed dial Copying phonebook entriesEditing entries Erasing entries Copying all entries Copying an entry Display the menu tree and direct command code table Programmable settings Rings Auto Recording Time *1 Minute Settings Number of Rings *1 2-9 RingsDisplay Mode Colour2 Multi Items Ringer Volume Handset Time Adjustment *1, *8 Caller ID Night Mode On/OffRing Delay 30 sec Memo Alarm Alarm1-5 Once Time Adjustment*1, *8 Caller ID Time Settings Set Date/Time *1Memo Alarm Once Alarm1-5 Daily Weekly Register Register H.set Power Failure Cancel Register*2Base Unit PIN*1 0000 Repeater Mode*1 Off AlarmNight mode Special programming Incoming call barring Caller ID subscribers only Changing the handset name Viewing/editing/erasing bar call numbers Setting call restrictionStoring an area code to be deleted automatically Storing unwanted callers Registering a handset to the base unit Registering a unitChanging the base unit PIN Personal Identification Number Operating additional units Dect repeater Setting the repeater mode Category ringer tone Using Caller ID serviceCaller ID features Call waiting and Caller ID compatible Caller list To store the name, continue from , Adding entries, Call screening Answering systemGreeting message Memory capacity including your greeting message Listening to messages using the handset Listening to messages using the base unit MbN Call Back a Listening to messages from the message listOperating the answering system Calling back Caller ID subscribers only Remote operation Remote access codeUsing the answering system remotely Remote commands Number of rings before the unit answers a call Answering system settingsFor service provider voice mail subscribers Turning on the answering system remotely Answering System Voice mail service Transferring calls, conference calls IntercomHandset locator Character entry modes Character entry Cyrillic character table Extended 1 character tableExtended 2 character table Display message Error messagesCause/solution General use TroubleshootingProblem Making/answering calls, intercom Programmable settingsBattery recharge Answering system Caller ID To attach Belt clipLiquid damage Wall mounting template Wall mounting Index Page Page Sales Department For your future referenceAttach your purchase receipt here