Panasonic TQBJ 0268-5 Raster position

66 –

ENGLISH

How to use ADVANCED MENU (continued)

Press ◄► to switch “FRAME

2.

DELAY”.

The setting will change as follows each time •

◄► is pressed.

DEFAULT SHORT

DEFAULT:•

This is the standard setting.

SHORT:•

This causes the pictures to be delayed after the

audio.

Note

When “FRAME DELAY” is set to “SHORT”, •

deterioration in the picture quality will occur.

Furthermore, the noise reduction function cannot be

used.

Raster position

When the whole area where the input picture can be

displayed is not used, the picture can be moved to

any position inside the display area.

Press ▲▼ to select “RASTER 1.

POSITION”.

EDGE BLENDING

FRAME DELAY

RASTER POSITION

OFF

DEFAULT

Press ENTER.2.

The “RASTER POSITION” screen will be •

displayed.

RASTER POSITION

V

H

0

0

Press ▲▼◄► to adjust the 3.

position.

When 4:3 pictures are displayed

Pressing ► button will move

the image to the right.

Pressing ◄ button will move

the image to the left.

Press MENU three times.4.

The on-screen indications disappear and the •

normal screen appears again.

Contents

Main Dear Panasonic Customer: Basic OperationSpecial FeaturesInformation Contents IMPORTANT SAFETY NOTICE IMPORTANT: THE MOULDED PLUG (U.K. only) Precautions with regard to safety WARNING Page Page Page Before Using Accessories Caution when moving the projector Cautions regarding setup Notes on use Do not touch the surface of the projection lens with bare hand. DLP chips Lamp Maintenance Caution: Disposal Location and function of each part Front Remote control unit Side Top Bottom Location and function of each part (continued) Front Projector Main Unit Rear Controls Side Location and function of each part (continued) Connection terminals Using the remote control unit Loading batteries Open battery compartment lid.1. $ # Insert the batteries.2. Setting projector ID number to remote control Using a wired remote control Installation Examples of system expansion Adjusting the feet Projection scheme Installation geometry When attaching an optional ceiling mount bracket (ET-PKD100H) Projection distances by the type of projection lenses (optional) Projection distances by the type of projection lenses For the screen aspect ratio of 4:3 (Units: m) For the screen aspect ratio of 16:9 (Units: m) Calculation formulas for projection distance by lens types Installation dimensions diagram Connection Before starting connection The pin-out and signal names of the S-VIDEO IN terminal are shown in the diagram below. The pin-out and signal names of the RGB2 IN terminal are shown in the diagram below. The pin-out and signal names of the DVI-D IN terminal are shown in the diagram below. Example of connecting with VIDEO devices Example of connecting with personal computers Installation of input module (optional) Installing the input module Types of the input modules (optional) Procedure of installation Remove the slot cover.1. Insert the input module.2. Fix the input module.3. Register the input signal.4. Installation of input module (optional) (continued) Connecting signals to the input module Connecting the signal to the SD-SDI input module Connecting the signal to the HD/SD-SDI input module Installation of input module (optional) (continued) Connecting the signal to the dual link HD/SD-SDI input module Connecting signals to the DVI-D input module How to install and remove the projection lens (optional) How to install the projection lens How to remove the projection lens Projection Power indicator lamp Connecting the power cord Powering up the projector Making adjustment and selection Powering off the projector How to adjust the lens How to adjust the focus, zoom and shift Adjustment range after lens position (optical shift) ET-D75LE6 Zoom Lens ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 The ET-D75LE5 has a fixed focal point, and so shift adjustment cannot be carried out. How to adjust the lens mounter for addressing unevenness of focusing About the focus balance Relation between the orientation of the lens and focus surface on the screen side z Procedure for adjusting the focus balance (adjusting the tilt with the lens mounter) Structure of lens mounter (Figure 2, Figure 3) z Adjustment procedure z How to adjust the lens (continued) Precautions for projector installation work z Registration of input signal data Registration of new data Renaming the registered signals Press to select the 1. signal whose details are to be displayed. Press ENTER.2. Clearing the data of registered signals 1. whose data is to be cleared. Press DEFAULT.2. Press ENTER.3. Sub memory Press ENTER.3. Press ENTER.4. Procedure to switch to sub memory Press on normal screen 1. (menu is not displayed). How to erase sub memory Basic operations using the remote control Using the SHUTTER Press SHUTTER on the remote 1. control or the main unit. Press SHUTTER again.2. On-screen display Automatic adjustment (AUTO SETUP) Press AUTO SETUP on the 1. remote control or the main unit. Turning on button illumination Press LIGHT on the remote 1. Using the FUNC1 button Changing the picture aspect ratio Press ASPECT on the remote 1. On-screen menus MAIN MENU SUB MENU PICTURE (pp. 52-57) On-screen menus (continued) POSITION (pp. 58-61) ADVANCED MENU (pp. 62-66) DISPLAY LANGUAGE (p. 67) DISPLAY OPTION (pp. 68-74) PROJECTOR SETUP (pp. 75-82) Using the menu screens Press MENU.1. Press to select the desired 2. item. Press ENTER to establish your 3. selection. Returning to the previous screen Adjusting the picture Switching the picture mode Press to select PICTURE 1. Press to switch PICTURE 2. Adjusting Contrast Adjusting Brightness This adjusts the brightness of dark (black) areas of the pictures. Press to select 1. BRIGHTNESS. Press or ENTER.2. The BRIGHTNESS individual adjustment screen will be displayed. Gamma setting Press to select GAMMA.1. Press or ENTER.2. Press to switch GAMMA.3. Sharpness setting Noise reduction setting Dynamic iris setting Registering the picture mode settings as presettings Setting the system selector To display pictures complying with the sRGB standard Adjusting the position Shift adjustment Press to select SHIFT.1. Press ENTER.2. Press to adjust the 3. position. For horizontal (right and left) Adjusting the aspect ratio Press to select ASPECT.1. Press or ENTER.2. Press to switch ASPECT.3. Adjusting the position (continued) Adjusting the zoom ratio Press to select ZOOM.1. Press ENTER.2. Press to select MODE.3. Press to switch MODE.4. Press to select 5. INTERLOCKED. Press to adjust the 3. correction amount. Press to select SUB 4. KEYSTONE or LINEARITY. Press to adjust the 5. correction amount. How to use ADVANCED MENU Digital cinema reality Press to select BLANKING. Press to select DIGITAL 1. CINEMA REALITY. Press or ENTER.2. Adjusting the input resolution Press to select INPUT 1. RESOLUTION. Press ENTER.2. Adjusting the clamp position Press to select CLAMP 1. POSITION. Edge blending adjustment Frame delay Raster position Setting the DISPLAY LANGUAGE Changing the display language Press to select the desired 1. language. Press ENTER to establish your 2. selection. Display Option settings Adjusting colour matching Press to select COLOR 1. MATCHING. Press to switch COLOR 2. MATCHING. If 3COLORS or 7COLORS Adjusting the colour matching using a colorimeter Large Screen Correction RGB IN (Only RGB input) DVI-D IN Press to select DVI-D IN.1. Press ENTER.2. Press to switch DVI EDID.3. Press to switch DVI 4. SIGNAL LEVEL. AUX DVI IN (Only when the ET-MD77DV is installed) Press to select AUX DVI IN. 1. Press ENTER.2. Press to switch AUX DVI 3. EDID. On-Screen display setting Press to select 1. ON-SCREEN DISPLAY. Press ENTER.2. Press to select the desired 3. item, and press to change the setting. OSD POSITION z Setting the startup logo Press to select STARTUP 1. LOGO. Press to switch STARTUP 2. LOGO. Projector setup Setting a projector ID Press to select 1. PROJECTOR ID. Press to switch 2. PROJECTOR ID. Press MENU twice.3. Installation Setting Altitude Mode Direction Lamp select Press to select LAMP 1. SELECT. Press to switch LAMP 2. SELECT. Press ENTER.3. Projector setup (continued) Lamp relay Press to select LAMP 1. RELAY. Press to switch LAMP 2. RELAY. RS-232C setting Press to select RS-232C.1. Status Press to select STATUS.1. Press ENTER.2. Press to move to the next 3. page. Press to move to the next 4. page. Auto power off Press to select AUTO 1. POWER OFF. Press to switch AUTO 2. POWER OFF. Setting FUNC1 Setting the date and time Save all user data Load all user data Initialize Service password P IN P Using the P IN P function Press ENTER.1. Press to select P IN P 2. Press to select a function.3. P IN P (continued) Displaying the internal test pattern Test pattern Press to search through the 1. various types of test patterns. Cycle of displayed internal test patterns Setting the security Displaying the security screen If using for the first time z Press , , , , , , and 1. in this order. If the existing password has been changed z Changing the text Changing the security password Setting the text Control device setup How to use network function Network standby Press to select NETWORK 1. STANDBY. Press to switch NETWORK 2. STANDBY. Initial setting of network Network control Press to select NETWORK 1. CONTROL. Press ENTER.2. Press to select items, and 3. press to change the setting. Network status Network connections Name and function of network function parts Accessing from the Web browser Basic control page Detail control page Projector status page Error information page OK: Normal operation FAILED: Occurrence of trouble When [FAILED] has appeared for an item z Parameter Description E-mail setup page Page E-mail setup page (continued) Authentication set up page Ping test page Contents of mail sent Mail with the contents shown below is sent when the E-mail settings have been established. z Mail with the contents shown below is sent when an error has occurred. z Adjust clock page Network config page Firmware update page Using the PJLink protocol Supported commands PJLink security authorization Using the serial terminals Examples of connection For RS-232C Single projector z Plural projectors z For RS-422 Single projector z Plural projectors z Pin assignments and signal names Communication conditions (Factory setting) Basic format Control commands Cable specifications Connecting to a PC For RS-232C z When multiple projectors are connected Using the Remote 2 terminal Example of a control panel layout Pin assignments and control Indication of monitor lamp LAMP 4 monitor (LAMP 4) LAMP 2 monitor (LAMP 2) LAMP 1 monitor (LAMP 1) LAMP 3 monitor (LAMP 3) Temperature monitor (TEMP) Name of monitor lamp Cleaning and replacement of air filter Procedure of cleaning Page Replacement of lamp unit WARNING Precautions on lamp unit replacement Timing of lamp unit replacement Indication after 1 800 hours Procedure of lamp unit replacement Notes when installing the ceiling mount bracket Installation procedure Before asking for service Symptoms Check point Page Self-diagnosis display Details Remedy Self-diagnosis display Details Remedy The self-diagnosis display and details of the failure may sometimes differ. Specifications Model No. PT-DW100E *1 to 35 or more (35 to 40 Appendix Compatible Signals *1: Only when using VESA CVT RB (Reduced Blanking) Appendix (continued) List of P IN P Noise reduction cannot be used. Subwindow Main window Dimensions Outside dimensions unit : mm Index A B C D R S T U W Information for Users on Collection and Disposal of Old Equipment and used Batteries Note: Trademark Acknowledgement