Adjusting the input Resolution | Panasonic TQBJ 0268-5 specs

2.Press ENTER.

•The “BLANKING” adjustment screen will be displayed.

BLANKING

UPPER	0
LOWER	0

3.Press ▲▼ to select the desired item for adjustment.

4.Press ◄► to adjust blanking.

•The adjustment value can be changed within a range of 0 to 384 vertically and 0 to 683 horizontally.

When correcting the upper blanking of the

screen (top)

Press ◄ button to move the blanking zone upward; ► button to downward.

When correcting the lower blanking of the

screen (bottom)

Press ► button to move the blanking zone upward; ◄ button to downward.

When correcting the left hand blanking of

the screen (left)

Press ► button to move the blanking zone to the right; ◄ button to the left.

When correcting the right hand blanking of

the screen (right)

Press ◄ button to move the blanking zone to the right; ► button to the left.

Adjusting the input

resolution

Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour.

1. Press ▲▼ to select “INPUT RESOLUTION”.

BLANKING

INPUT RESOLUTION

CLAMP POSITION

2. Press ENTER.
	• The “INPUT RESOLUTION” screen will be
	displayed.						Operation

	INPUT RESOLUTION
	TOTAL DOTS
	TOTAL DOTS		1344
	DISPLAY DOTS		1024

3. Press ▲▼ to select “TOTAL
	DOTS”, “DISPLAY DOTS”,
	“TOTAL LINES” or “DISPLAY						Basic
	LINES”, and the press ◄► to						Basic
	LINES”, and the press ◄► to
	adjust it.
	• Each item automatically displays a value in
	response to the type of the input signal. If
	vertical stripes appear on the screen or the
	image is partly missing, increase or decrease
	the displayed value while observing the screen
	to achieve the optimal value.

Note

•The abovementioned vertical stripes will not appear on the screen when all signals are input.

•The picture may be distorted during the adjusting operation, but this is not a fault.

•The input resolution can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN.

Adjusting the clamp

position

Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green.

1. Press ▲▼ to select “CLAMP POSITION”.

INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING	OFF

ENGLISH – 63

Image 63

Panasonic TQBJ 0268-5 operating instructions Adjusting the input Resolution, Adjusting the clamp Position

Contents

Operating Instructions Dear Panasonic Customer Contents Important Safety Notice Important the Moulded Plug U.K. only Getting StartedFuse Page „ Do not place sets directly on top of each other „ Do not disassemble the lamp unit„ Do not place liquid containers on top of the projector „ Do not insert any foreign objects into the projector English English 76, to on Before UsingAccessories Do not place the projector on a vinyl sheet or carpet „ Lamp „ MaintenanceDisposal „ To view clear images „ Front Remote control unitRemote control operation indicator lamp Location and function of each part Remote control transmitter window „ Side„ Bottom Burglar hook Remote control receiver window frontProjector Main Unit „ Rear „ Controls Connection Terminals p ControlsSelf-diagnosis display ･･･････････ pp Light ON/OFF button „ Connection terminals Using the remote control unit Effective range of remote Control operationLoading batteries Using a wired remote Control Setting projector ID Number to remote control Examples of system expansion Installation Projection scheme Adjusting the feetInstallation geometry Lens Dimension of L1 Approx Started GettingSide View Top View For the screen aspect ratio of 169 Units m „ Calculation formulas for projection distance by lens types Dimensions applying when Installation dimensions diagram Pin No Pin No SignalConnection Before starting connection Control PC Video deck TBC built-in Example of connecting with Video devices Example of connecting with personal computers „ Types of the input modules optional Installation of input module optionalInstalling the input module Module Module model Terminal Signal formats supported Insert the input module „ Procedure of installationFix the input module Register the input signal Remove the slot cover DVI-D ET-MD77DV Connecting signals to the input module HD/SD-SDI input module optional Connecting the signal to the SD-SDI input moduleConnecting the signal to the HD/SD-SDI input module SD-SDI input module optional Dual link HD/SD-SDI input module optional Connecting signals to the DVI-D input module Pin SignalDVI-D input module optional How to remove Projection lens How to install Projection lens Projection Power indicator lampConnecting the power Cord Indicator Projector status Status Powering up the projector Making adjustment SelectionPress Power on Press Power Standby Powering off the projector „ Using the remote control How to adjust the lensHow to adjust the focus, zoom and shift Press to select an item and adjust it Adjustment range after lens position optical shift Moving the projection lens position to the home positionModel number of projection lens Illustration of influence of lens orientation „ About the focus balance English Precautions for projector installation work Press Enter Registration of input signal dataRegistration of new data Displayed Sub memory Clearing the data Registered signalsPress Default „ How to register into sub memory „ How to erase sub memory „ On-screen indicationsRestrictions Status function Using the Shutter FunctionSwitching the input signal On-screen display Function Displaying the internal Test pattern Automatic adjustmentUsing the FUNC1 button Turning on button Illumination Changing the picture Aspect ratio Press Aspect on the remote control Select the item to be set On-screen menus„ Picture pp Icon Main Menu item „ Advanced Menu pp „ Projector Setup pp„ P in P pp „ Test Pattern p „ Signal List pp „ Security pp „ Position pp Resetting to the factory Default Using the menu screens Adjusting the picture Switching the picture modeAdjusting Contrast Adjusting the colour Temperature Adjusting BrightnessAdjusting Colour Adjusting Tint Press to select Gamma Gamma settingPress to switch Color Temperature Press to switch Gamma Sharpness setting Noise reduction settingDynamic iris setting Registering the picture mode Settings as presettings ET-MD100SD4 To display pictures complying With the sRGB standardDisplay the Picture screen. p Press to select Picture Press to select Natural Press to select Color Press to select Shift Adjusting the positionShift adjustment „ For vertical up and down adjustment Adjusting the aspect ratio Press to switch AspectPress to select Aspect Adjusting the zoom ratio Clock phase adjustmentKeystone distortion Correction Press to adjust the correction amount Digital cinema reality How to use Advanced MenuBlanking adjustment Press to switch Digital Cinema Reality Adjusting the clamp Position Adjusting the input Resolution Edge blending adjustment Frame delay Press to select Frame DelayPress to select Bright Inside Press Enter Press to select Raster Position Press to switch Frame DelayPress to adjust the position Raster position Display Language Setting the Display LanguageChanging the display Language Press to select the desired language Press to select Color Matching Display Option settingsAdjusting colour matching Press to switch Color Matching Press to select Target Data Using a colorimeterPress to adjust the values Press to select Measured Data Press Enter Large Screen Correction RGB in Only RGB input Wide Press to switch DVI EdidPress to switch DVI Press to select DVI-D AUX DVI in Only when ET-MD77DV is installed Back Colour On-Screen display settingFeatures Special Press to select Startup Logo Setting the startup logoPress to switch Back Color Press to switch Startup Logo Press to select Projector ID Projector setupSetting a projector ID Projector Setup Installation Setting Altitude ModeDirection Press to switch Lamp Select Lamp selectPress to select Lamp Select RS-232C setting Remote2 modeLamp relay Press to move to the next Cleaning the air filterStatus Press to select Status Press to switch Auto Power OFF Auto power offPress to switch Time Press to select Auto Power OFF Setting FUNC1 Setting the date and timeSave all user data Press to select Load ALL User Data Service passwordLoad all user data Initialize USER1, USER2, USER3 Using the P in P functionSetting the P in P function Press to select P in P Mode Type Main WindowSUB Window Frame Lock Pattern Displaying the internal test pattern„ Cycle of displayed internal test Patterns Press to select Test Setting the security Setting the security PasswordDisplaying the security Screen Changing the security Password Setting the textChanging the text Remote Controller Control device setupPress to select Control Device Setup Press to select Control Panel or Remote Controller How to use network function Initial setting of network FunctionNetwork standby Press to select Network Status Network controlNetwork status Press to select Network LAN10/100 lamp yellow Network connections„ Name and function of network function parts LAN LINK/ACT lamp green Accessing from the Web browser „ Change PasswordPress OK to display the Projector status Monitor information button Detailed set up button„ Basic control Selection tabs Menu display Lens adjustment Test pattern display„ Detail control „ Projector status „ Error information OK Normal operation Failed Occurrence of troubleParameter Description „ E-mail setup English English „ Ping test „ Authentication set up „ Contents of mail sent „ Network config „ Adjust clock „ Firmware update Command Control details Using the PJLink protocolSupported commands „ PJLink security authorization Examples of connection Using the serial terminals„ Pin assignments and signal names „ Communication conditions Factory setting Pin Signal Description No. name Signal level RS-422-compliant„ For RS-422 Control commands Command Function of command RemarksBasic format Cable specifications „ Connecting to a PC„ When multiple projectors are connected Names of terminals Open H Short L Using the Remote 2 terminalExample of a control panel layout Pin assignments and control Lamp Indication of monitor lamp Procedure of cleaning Cleaning and replacement of air filter Install the movable metal mesh Filter to the filter cleaning unitInstall the brush cover so that it „ Indication after 1 800 hours Replacement of lamp unitPrecautions on lamp unit replacement Timing of lamp unit replacement Procedure of lamp unit replacement Lamp unit to be replaced untilLamp unit cover screw Installation procedure Power does not turn on Symptoms Check point Details Remedy Self-diagnosis display FF0 Specifications Model NoPT-DW100E RGB2 input Appendix Compatible Signals MAC21 Subwindow List of P in P Outside dimensions Dimensions Index Wired remote control ･･････････････････････････ For business users in the European Union Trademark Acknowledgement