Dual link HD/SD-SDI input module optional | Panasonic TQBJ 0268-5

Installation of input module (optional) (continued)

Connecting the signal to the dual link HD/SD-SDI input

module

Dual link HD/SD-SDI input module (optional)

ET-MD100SD4

Dual Link
HD-SDI
Module	LINK-A	LINK-B
ET-MD100SD4		SERIAL IN

HD-SDI or

SD-SDI signal

Business digital

VCR

•When connecting a single link signal, connect to the LINK-A terminal.

•When connecting a dual link signal, connect to both the LINK-A and LINK-B terminals.

Note

•You can switch the input format mode from the SYSTEM SELECTOR menu. (pp. 56-57)

•Settings specific to the connected device are required. (pp. 72-73)

•To send the pictures properly, use a connecting cable with the specifications of 5CFB or higher (5CFB, 7CFB, etc.) or of Belden1694A or higher. Also, use a cable that is shorter than 100 m.

•Make sure that the cables used to link LINK-A terminal and LINK-B terminal are of the same type and length. If there is a difference in length greater than 4 m between the two cables, the images will not be projected correctly.

•When connecting to dual link signals, connect directly to the signal output device without connecting through a distributor or other such device. A phase difference may occur between the LINK-A signal and LINK-B signal, which may prevent the image from being correctly projected.

•If the connected signal is unstable, the automatic distinction function may not operate correctly. In this case, switch to a mode that better suits the signal format from the SYSTEM SELECTOR menu.

32 – ENGLISH

Image 32

Panasonic TQBJ 0268-5 operating instructions Dual link HD/SD-SDI input module optional

Contents

Operating Instructions Dear Panasonic Customer Contents Important Safety Notice Fuse Important the Moulded Plug U.K. onlyGetting Started Page „ Do not disassemble the lamp unit „ Do not place liquid containers on top of the projector„ Do not insert any foreign objects into the projector „ Do not place sets directly on top of each other English English Before Using AccessoriesDo not place the projector on a vinyl sheet or carpet 76, to on „ Maintenance Disposal„ To view clear images „ Lamp Remote control unit Remote control operation indicator lampLocation and function of each part „ Front „ Bottom Remote control transmitter window„ Side Remote control receiver window front Projector Main Unit„ Rear Burglar hook Self-diagnosis display ･･･････････ pp Light ON/OFF button „ ControlsConnection Terminals p Controls „ Connection terminals Loading batteries Using the remote control unitEffective range of remote Control operation Setting projector ID Number to remote control Using a wired remote Control Installation Examples of system expansion Adjusting the feet Installation geometryLens Dimension of L1 Approx Projection scheme Side View Top View StartedGetting For the screen aspect ratio of 169 Units m „ Calculation formulas for projection distance by lens types Installation dimensions diagram Dimensions applying when Pin No Signal ConnectionBefore starting connection Pin No Example of connecting with Video devices Control PC Video deck TBC built-in Example of connecting with personal computers Installation of input module optional Installing the input moduleModule Module model Terminal Signal formats supported „ Types of the input modules optional „ Procedure of installation Fix the input module Register the input signalRemove the slot cover Insert the input module Connecting signals to the input module DVI-D ET-MD77DV Connecting the signal to the SD-SDI input module Connecting the signal to the HD/SD-SDI input moduleSD-SDI input module optional HD/SD-SDI input module optional Dual link HD/SD-SDI input module optional DVI-D input module optional Connecting signals to the DVI-D input modulePin Signal How to install Projection lens How to remove Projection lens Power indicator lamp Connecting the power CordIndicator Projector status Status Projection Press Power on Powering up the projectorMaking adjustment Selection Powering off the projector Press Power Standby How to adjust the lens How to adjust the focus, zoom and shiftPress to select an item and adjust it „ Using the remote control Model number of projection lens Adjustment range after lens position optical shiftMoving the projection lens position to the home position „ About the focus balance Illustration of influence of lens orientation English Precautions for projector installation work Registration of input signal data Registration of new dataDisplayed Press Enter Clearing the data Registered signals Press Default„ How to register into sub memory Sub memory Restrictions „ How to erase sub memory„ On-screen indications Using the Shutter Function Switching the input signalOn-screen display Function Status function Automatic adjustment Using the FUNC1 buttonTurning on button Illumination Displaying the internal Test pattern Press Aspect on the remote control Changing the picture Aspect ratio On-screen menus „ Picture ppIcon Main Menu item Select the item to be set „ Projector Setup pp „ P in P pp „ Test Pattern p „ Signal List pp „ Security pp„ Position pp „ Advanced Menu pp Using the menu screens Resetting to the factory Default Adjusting Contrast Adjusting the pictureSwitching the picture mode Adjusting Brightness Adjusting ColourAdjusting Tint Adjusting the colour Temperature Gamma setting Press to switch Color TemperaturePress to switch Gamma Press to select Gamma Dynamic iris setting Sharpness settingNoise reduction setting Registering the picture mode Settings as presettings To display pictures complying With the sRGB standard Display the Picture screen. p Press to select PicturePress to select Natural Press to select Color ET-MD100SD4 Adjusting the position Shift adjustment„ For vertical up and down adjustment Press to select Shift Press to select Aspect Adjusting the aspect ratioPress to switch Aspect Keystone distortion Correction Adjusting the zoom ratioClock phase adjustment Press to adjust the correction amount How to use Advanced Menu Blanking adjustmentPress to switch Digital Cinema Reality Digital cinema reality Adjusting the input Resolution Adjusting the clamp Position Edge blending adjustment Press to select Bright Inside Press Enter Frame delayPress to select Frame Delay Press to switch Frame Delay Press to adjust the positionRaster position Press to select Raster Position Setting the Display Language Changing the display LanguagePress to select the desired language Display Language Display Option settings Adjusting colour matchingPress to switch Color Matching Press to select Color Matching Using a colorimeter Press to adjust the valuesPress to select Measured Data Press Enter Press to select Target Data RGB in Only RGB input Large Screen Correction Press to switch DVI Edid Press to switch DVIPress to select DVI-D Wide AUX DVI in Only when ET-MD77DV is installed On-Screen display setting FeaturesSpecial Back Colour Setting the startup logo Press to switch Back ColorPress to switch Startup Logo Press to select Startup Logo Projector setup Setting a projector IDProjector Setup Press to select Projector ID Direction Installation SettingAltitude Mode Press to select Lamp Select Press to switch Lamp SelectLamp select Lamp relay RS-232C settingRemote2 mode Cleaning the air filter StatusPress to select Status Press to move to the next Auto power off Press to switch TimePress to select Auto Power OFF Press to switch Auto Power OFF Save all user data Setting FUNC1Setting the date and time Service password Load all user dataInitialize Press to select Load ALL User Data Using the P in P function Setting the P in P functionPress to select P in P Mode USER1, USER2, USER3 Main Window SUB WindowFrame Lock Type Displaying the internal test pattern „ Cycle of displayed internal test PatternsPress to select Test Pattern Displaying the security Screen Setting the securitySetting the security Password Changing the text Changing the security PasswordSetting the text Control device setup Press to select Control Device SetupPress to select Control Panel or Remote Controller Remote Controller Network standby How to use network functionInitial setting of network Function Network control Network statusPress to select Network Press to select Network Status Network connections „ Name and function of network function partsLAN LINK/ACT lamp green LAN10/100 lamp yellow Press OK to display the Projector status Accessing from the Web browser„ Change Password Detailed set up button „ Basic controlSelection tabs Monitor information button Lens adjustment Test pattern display „ Detail control„ Projector status Menu display Parameter Description „ Error informationOK Normal operation Failed Occurrence of trouble „ E-mail setup English English „ Authentication set up „ Ping test „ Contents of mail sent „ Adjust clock „ Network config „ Firmware update Using the PJLink protocol Supported commands„ PJLink security authorization Command Control details Using the serial terminals „ Pin assignments and signal names„ Communication conditions Factory setting Examples of connection „ For RS-422 Pin Signal Description No. nameSignal level RS-422-compliant Basic format Control commandsCommand Function of command Remarks „ When multiple projectors are connected Cable specifications„ Connecting to a PC Using the Remote 2 terminal Example of a control panel layoutPin assignments and control Names of terminals Open H Short L Indication of monitor lamp Lamp Cleaning and replacement of air filter Procedure of cleaning Install the brush cover so that it Install the movable metal meshFilter to the filter cleaning unit Replacement of lamp unit Precautions on lamp unit replacementTiming of lamp unit replacement „ Indication after 1 800 hours Lamp unit cover screw Procedure of lamp unit replacementLamp unit to be replaced until Installation procedure Symptoms Check point Power does not turn on Self-diagnosis display Details Remedy FF0 PT-DW100E SpecificationsModel No RGB2 input Compatible Signals Appendix MAC21 List of P in P Subwindow Dimensions Outside dimensions Index Wired remote control ･･････････････････････････ Trademark Acknowledgement For business users in the European Union