Projector setup (continued)
2.Press ENTER.
•The “AIR FILTER CLEANING” screen will be displayed.
•You can select the automatic cleaning time (“TIME”) and also force cleaning to be carried out immediately (“EXECUTE”).
AIR FILTER CLEANING
TIME | 00:00 |
|
|
|
|
EXECUTE
3. Press ▲▼ to select “TIME”. | |
• Select “TIME” and then set the time for | |
automatic cleaning to be carried out. | |
• If you would like cleaning to be carried out | |
straight away, select “EXECUTE” and then | |
press ENTER. |
|
4. Press ◄► to switch “TIME”. | |
• The setting will change as follows each time | |
◄► is pressed. |
|
00:00 | 23:50 |
(in units of 10 minutes) |
|
• The default setting is “00:00” (midnight). | |
Example: When the default setting is in use, | |
automatic cleaning will start at 00:00 if the | |
projector is in projection mode. If the time | |
is set to 7:00, automatic cleaning will start | |
at that time if the projector is in projection | |
mode. |
|
Note
•Contaminants such as oil and cigarette tar cannot be cleaned when air filter cleaning is carried out.
•The air filter cleaning monitor (FILTER CLEANING) will flash blue while cleaning of the air filter is in progress. If there is a problem with the air filter, the air filter cleaning monitor (FILTER CLEANING) will light red.
•The time taken for cleaning is approximately 30 to 40 seconds.
•The setting time will be the local time. (p. 81)
•If the projector is not in projection mode when the setting time is reached, automatic cleaning will not be carried out.
•Automatic cleaning will not be carried out if 24 hours have not yet elapsed since cleaning was last carried out (either by automatic cleaning or forced cleaning).
Example: If the setting time is 7:00 and forced cleaning is carried out at 9:00, then automatic cleaning will not be carried out at 7:00 on the following day.
|
|
|
|
|
|
|
| 46 hours elapsed |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
| 22 hours elapsed |
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Setting time | Setting time | Setting time | ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Automatic Forced | (No cleaning) | Automatic | |||||||||||||||
cleaning cleaning |
|
|
|
|
| cleaning | |||||||||||
•If the time is set to a time which is within 24 hours from the last time cleaning was carried out, automatic cleaning will not be carried out the next time the setting time is reached. Instead, cleaning will be carried out when the setting time is reached on the following day.
Example: If cleaning was carried out at 10:00, and the cleaning time setting is then changed to 20:00, automatic cleaning will be carried out at 20:00 on the following day.
34 hours elapsed
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 10 hours elapsed |
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setting time | Setting time | Setting time | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Automatic | (No cleaning) | Automatic | |||||||||||||
cleaning |
|
|
|
|
| cleaning | |||||||||
Time reset
•When projection starts (when the power is turned on), automatic cleaning will be carried out immediately if more than 24 hours have elapsed since cleaning was last carried out.
Auto power off
The projector can be set to automatically enter the standby state if no signal is input before the set time elapses.
1. Press ▲▼ to select “AUTO POWER OFF”.
AIR FILTER CLEANING
AUTO POWER OFF | DISABLE |
|
|
|
|
FUNC1
2.Press ◄► to switch “AUTO POWER OFF”.
•The setting will change as follows each time ◄► is pressed.
DISABLE
45MIN.
60MIN.
90MIN.
75MIN.
