Turning off the power | Dukane 8107HWI specification

Power on/off

Turning off the power

1. Press the STANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds.

2. Conﬁrm that there is nothing that the lens door hits while closing. Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. The lens door will close right after the lamp goes off.

However, to maintain better picture quality, the lens door will close after the lamp has been cooled down when the projector is installed upside down such as in ceiling mount installation. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete (107).

Do not turn the projector on for about 10 minutes or more after turning it off. Also, do not turn the projector off shortly after turning it on. Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

WARNING ►Be careful not to pinch your ﬁnger with the lens door, to prevent an injury.

►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot.

►Remove the power cord for complete separation. The power outlet should be close to the projector and easily accessible.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices.

•This projector has the function that can make the projector automatically turn on/ off. Please refer to the DIRECT POWER ON (55) and AUTO POWER OFF (56) items of the OPTION menu.

20

Image 22

Dukane 8107HWI user manual Turning off the power

Contents

Model 8107HWI Page Thank you for purchasing this projector About this manualProjector Trademark acknowledgment Contents Features Checking the contents of package HOT Part namesProjector Small Hdmi Computer IN2 Control panel STANDBY/ON buttonButtons Focus +/- buttons 1415 MY Button 1 button MY Button 2 button Keystone button Down button Volume + buttonComputer button Zoom button Zoom + button Position button 26 Setting up Arrangement Arrangement Connecting with your devices About Plug-and-Play capability VCR/DVD/Blu-ray Disc Player Computer Connecting with your devices Monitor Microphone system USB storage Device Access point Computer Hdmi Security bar Anti-theft chain or wire Connecting to a power supplyUsing the security bar and slot Security slot Using the cable cover About the remote control signal Remote controlInstalling the batteries Hitachi MAXELL, Part No.LR6 or R6P Using as a simple PC mouse & keyboard Changing the frequency of remote control signalUSB Type B port Exchanging the tip of the pen Installing the batteryInteractive pen Hitachi MAXELL, Part No. LR03 Power indicator Power on/offTurning on the power STANDBY/ON button Turning off the power Operating Adjusting the volumeSelecting an input signal Temporarily muting the sound Video button Press the MY Source / DOC. Camera button onComputer button MY Source For an Hdmi TM signal Searching an input signalFor a computer signal Selecting an aspect ratio Zoom button Adjusting the projectors elevatorAdjusting the zoom and focus Zoom + button For a component video signal Using the automatic adjustment featureFor a video signal and s-video signal Focus button Position button Adjusting the positionCorrecting the keystone distortions Keystone button Using the magnify feature Magnify ON/OFF button Freeze button Temporarily freezing the screenTemporarily blanking the screen Blank button Advanced Menu Using the menu functionESC button Reset button Enter button Indication in OSD On Screen Display Indication Meaning Aspect DescriptionInteractive Zoom Reset Picture ModeECO Mode Mirror Interactive menu Contrast Picture menuBrightness Gamma Custom Custom MIDLOW Color OFF SharpnessPresentation Active Iris For an Hdmitm signal For a computer signalImage menu Position Signal, the range of this adjustment depends on Over ScanSelected will reset the H Position to the default setting USB Type B or Hdmi port Size PhaseAuto Adjust Execute High MID LOW Input menuTV Film OFF Video NR Hdmi Format Video FormatHdmi Range Computer Auto Sync on G OFFFrame Lock Resolution Left MID Right Setup menuShift No Input is Detected Sync is OUT of Range Invalid Scan Freq Perfect FIT Input button On OFF Normal Hinvert Vinvert Normal ECONormal Saving Speaker VolumeAudio menu Audio Source MIC Level MIC VolumeHdmi Audio High LOW Screen menu English Français Deutsch Español MyScreen Capturing error has occurred. Please try againMyScreen registration is ﬁnished MyScreen Lock Message Source Name Template Mode Description Closed CaptionDisplay Channel Option menu Direct PowerComputer IN2 LAN USB Type a Video Video Hdmi USB Type B Mouse USB Display Auto PowerOFF USB Type B Cancel Cancel OKLamp Time MY Button No Messenger Data appears Zoom Turns the D-ZOOM mode on/off. When the D-ZOOM Active Iris Changes the active iris modePicture Mode Changes the Picture Mode Mode is on, use the / cursor buttons to adjust Ghost ServiceFAN Speed Filter Message Lens Door Open KEY LockLens Door Lock Lens Door Close 1NORMAL 2HIGH Remote FreqControl port Communication Type Serial SettingsBaud Rate Service Parity Response Limit Time Transmission Method Factory Reset Information Network menu SetupDhcp IP Address DefaultSetup Gateway Subnet Projector Name MY Image AMX D.D Presenter QuitPresentation Multi PC Section SwitchingUser Name Guide Enter to the Security menu PasswordSecurity menu Security Turning off the MyScreen Password Turning on the MyScreen PasswordMyScreen Turning off the PIN Lock PIN LockTurning on the PIN Lock If you have forgotten your PIN code Turning on the Transition Detector Transition DetectorTurning off the Transition Detector Turning on the MY Text Password MY Text PasswordTurning off the MY Text Password MY Text Writing System requirements Presentation toolsInteractive Function Application Interactive Function Connection during use Using the pen Preliminary preparation Basic pen operation Customizing the pen Using StarBoard Software Supported format PC-LESS PresentationSupported storage media Supported ﬁle format Thumbnail mode Thumbnail menu Selected image Thumbnail images Down Setup menu for the selected imageOperating by buttons or keys Enter Input Operating by the menu on the Thumbnail screen PC-LESS Presentation Full Screen Mode Slideshow mode Control Projector Software Play Playlist Example of playlist.txt ﬁles Hardware and software requirement for computer USB DisplayUSB Port USB cable 1 piece Right-Click menu Floating menu Options window Replacing the lamp MaintenanceType number 456-8104HW Replacing the lamp High Voltage High Temperature Lamp warning Type number UX37191 Filter set Cleaning and replacing the air ﬁlterStitched side On next Cleaning and replacing the air ﬁlter 100 Hitachi MAXELL, part number CR2032 or CR2032H Replacing the internal clock battery101 Cleaning cloth 102 Maintenance of the pen Caring for the cabinet and remote controlMaintenance of the pen sensors horns Inside of the projector Other care 104 An improper signal is input TroubleshootingThere is no input signal Related messages Button operation is not available Internal temperature is rising106 Regarding the indicator lamps Has become heated It is time to clean the air ﬁlterThere is a possibility that the interior portion Lens door is not opened properly Resetting all settings Audio SOURCE/SPEAKER setting is not correct Signal cables are not correctly connectedVolume is adjusted to an extremely low level Mode selected for Hdmi Audio is not suitable Projector is operating in Eco mode Color settings are not correctly adjustedColor Space setting is not suitable Frame Lock function cannot work on the current Input signal Communication Type for the Control port is Computer cannot start up in the current hardwareSaving function is working Set to Network Bridge Is the USB cable connected correctly? Is the use of USB cables disabled?Is the power of the projector turned on? Is the system started up in the correct sequence? Are you using more than one pen at the same time? This may be due to poor contact of the batteryHas the battery run out? Is the volume from the speaker of the projector too loud? Is alignment of the pen position correctly performed? StarBoard Software ﬁles may be corrupted, orIs the tip of the pen worn out? Is the projector inclined? Is a part of the image enlarged using the Magnify Function? Is the projector correctly installed?Is the computer image projected within the area Screen? End User License Agreement for the Projector Software Speciﬁcations117