Power on/off, Turning on the power | Dukane 8107HWI instruction

		Power on/off
	Power on/off
	Turning on the power	STANDBY/ON button
	Make sure that the power cord is ﬁrmly	STANDBY/ON button
	Make sure that the power cord is ﬁrmly
	1. and correctly connected to the projector	POWER indicator
	and the outlet.
	Make sure that the POWER indicator is
	2. steady orange (107).
	Conﬁrm that there is nothing that the lens
	3. door hits while opening. Press STANDBY/
	ON button on the projector or the
	remote control. The lens door opens, the
	projection lamp lights up, and the POWER	- + - +
	indicator begins to blink green. When the
	power is completely on, the indicator will
	stop blinking and light in steady green
	(107).

WARNING ►Never look into the projection lens or mirror while the projection lamp lights, since the projection lamp ray may cause a trouble on your eyes.

►Be careful not to pinch your ﬁnger with the lens door, to prevent an injury.

►Do not place the projector vertically with the lens door open as shown in the ﬁgure on the right. It could cause malfunction or injury. ►Do not stand under the projector mounted on the wall or ceiling, when its lens door is opening or closing. Moreover, do not look at the mirror when the lens door is opening or closing.

►Never touch a lens door or mirror. If the mirror is broken, the projected image will be distorted. Close the lens door, and contact your dealer.

19

Image 21

Dukane 8107HWI user manual Power on/off, Turning on the power, STANDBY/ON button, Power indicator

Contents

Model 8107HWI Page Projector About this manualThank you for purchasing this projector Trademark acknowledgment Contents Checking the contents of package Features Projector Part namesHOT Small Buttons Focus +/- buttons Control panel STANDBY/ON buttonHdmi Computer IN2 1415 Computer button Down button Volume + buttonMY Button 1 button MY Button 2 button Keystone button Zoom button Zoom + button Position button 26 Arrangement Setting up Arrangement Connecting with your devices VCR/DVD/Blu-ray Disc Player Computer About Plug-and-Play capability Connecting with your devices USB storage Device Monitor Microphone system Hdmi Access point Computer Using the security bar and slot Connecting to a power supplySecurity bar Anti-theft chain or wire Security slot Using the cable cover Installing the batteries Remote controlAbout the remote control signal Hitachi MAXELL, Part No.LR6 or R6P Changing the frequency of remote control signal Using as a simple PC mouse & keyboardUSB Type B port Interactive pen Installing the batteryExchanging the tip of the pen Hitachi MAXELL, Part No. LR03 Turning on the power Power on/offPower indicator STANDBY/ON button Turning off the power Selecting an input signal Adjusting the volumeOperating Temporarily muting the sound Computer button Press the MY Source / DOC. Camera button onVideo button MY Source For a computer signal Searching an input signalFor an Hdmi TM signal Selecting an aspect ratio Adjusting the zoom and focus Adjusting the projectors elevatorZoom button Zoom + button For a video signal and s-video signal Using the automatic adjustment featureFor a component video signal Focus button Correcting the keystone distortions Adjusting the positionPosition button Keystone button Magnify ON/OFF button Using the magnify feature Temporarily blanking the screen Temporarily freezing the screenFreeze button Blank button ESC button Reset button Using the menu functionAdvanced Menu Enter button Indication Meaning Indication in OSD On Screen Display Interactive DescriptionAspect Zoom ECO Mode Picture ModeReset Mirror Interactive menu Brightness Picture menuContrast Gamma LOW Custom MIDCustom Color Presentation SharpnessOFF Active Iris For a computer signal For an Hdmitm signalImage menu Selected will reset the H Position to the default setting Signal, the range of this adjustment depends on Over ScanPosition USB Type B or Hdmi port Auto Adjust PhaseSize Execute TV Film OFF Input menuHigh MID LOW Video NR Video Format Hdmi FormatHdmi Range Auto Sync on G OFF ComputerFrame Lock Resolution Shift Setup menuLeft MID Right No Input is Detected Sync is OUT of Range Invalid Scan Freq On OFF Perfect FIT Input button Normal ECO Normal Hinvert VinvertNormal Saving Audio menu VolumeSpeaker Audio Source Hdmi Audio MIC VolumeMIC Level High LOW English Français Deutsch Español Screen menu Capturing error has occurred. Please try again MyScreenMyScreen registration is ﬁnished Message MyScreen Lock Source Name Template Display Description Closed CaptionMode Channel Direct Power Option menuComputer IN2 LAN USB Type a Video Video Hdmi USB Type B OFF Auto PowerMouse USB Display USB Type B Cancel OK CancelLamp Time No Messenger Data appears MY Button Picture Mode Changes the Picture Mode Active Iris Changes the active iris modeZoom Turns the D-ZOOM mode on/off. When the D-ZOOM Mode is on, use the / cursor buttons to adjust FAN Speed ServiceGhost Filter Message Lens Door Lock KEY LockLens Door Open Lens Door Close Remote Freq 1NORMAL 2HIGHControl port Baud Rate Service Serial SettingsCommunication Type Parity Transmission Method Response Limit Time Information Factory Reset Setup Network menuDhcp Setup Gateway DefaultIP Address Subnet Projector Name AMX D.D MY Image Quit PresenterPresentation Section Switching Multi PCUser Name Guide Security menu PasswordEnter to the Security menu Security Turning on the MyScreen Password Turning off the MyScreen PasswordMyScreen Turning on the PIN Lock PIN LockTurning off the PIN Lock If you have forgotten your PIN code Transition Detector Turning on the Transition DetectorTurning off the Transition Detector MY Text Password Turning on the MY Text PasswordTurning off the MY Text Password Writing MY Text Interactive Function Presentation toolsSystem requirements Application Interactive Function Connection during use Preliminary preparation Using the pen Customizing the pen Basic pen operation Using StarBoard Software Supported storage media PC-LESS PresentationSupported format Supported ﬁle format Thumbnail menu Selected image Thumbnail images Thumbnail mode Operating by buttons or keys Setup menu for the selected imageDown Enter Input Operating by the menu on the Thumbnail screen PC-LESS Presentation Full Screen Mode Control Projector Software Slideshow mode Play Example of playlist.txt ﬁles Playlist USB Display Hardware and software requirement for computerUSB Port USB cable 1 piece Floating menu Right-Click menu Options window Maintenance Replacing the lampType number 456-8104HW Replacing the lamp Lamp warning High Voltage High Temperature Cleaning and replacing the air ﬁlter Type number UX37191 Filter setStitched side On next 100 Cleaning and replacing the air ﬁlter Replacing the internal clock battery Hitachi MAXELL, part number CR2032 or CR2032H101 102 Cleaning cloth Maintenance of the pen sensors horns Caring for the cabinet and remote controlMaintenance of the pen Inside of the projector 104 Other care There is no input signal TroubleshootingAn improper signal is input Related messages Internal temperature is rising Button operation is not available106 Regarding the indicator lamps There is a possibility that the interior portion It is time to clean the air ﬁlterHas become heated Lens door is not opened properly Resetting all settings Volume is adjusted to an extremely low level Signal cables are not correctly connectedAudio SOURCE/SPEAKER setting is not correct Mode selected for Hdmi Audio is not suitable Color Space setting is not suitable Color settings are not correctly adjustedProjector is operating in Eco mode Frame Lock function cannot work on the current Input signal Saving function is working Computer cannot start up in the current hardwareCommunication Type for the Control port is Set to Network Bridge Is the power of the projector turned on? Is the use of USB cables disabled?Is the USB cable connected correctly? Is the system started up in the correct sequence? Has the battery run out? This may be due to poor contact of the batteryAre you using more than one pen at the same time? Is the volume from the speaker of the projector too loud? Is the tip of the pen worn out? StarBoard Software ﬁles may be corrupted, orIs alignment of the pen position correctly performed? Is the projector inclined? Is the projector correctly installed? Is a part of the image enlarged using the Magnify Function?Is the computer image projected within the area Screen? Speciﬁcations End User License Agreement for the Projector Software117