Searching an input signal, For a computer signal | Dukane 8107HWI

Operating

Searching an input signal

1. Press SEARCH button on the remote control.

The projector will start to check its input ports as below in order to ﬁnd any input signals.

When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

COMPUTER IN1 COMPUTER IN2
VIDEO	LAN

SEARCH button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGEVOLUME

UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

1 2

S-VIDEO	USB TYPE A
HDMI	USB TYPE B

●While ON is selected for AUTO SEARCH item in OPTION menu (55), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

●It may take several seconds to project the images from the USB TYPE B port.

Selecting an aspect ratio

1. Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

For a computer signal

NORMAL 4:3 16:9 16:10 NATIVE

ASPECT button

MY SOURCE/

VIDEO COMPUTER DOC.CAMERA

ASPECT AUTO SEARCH BLANK

MAGNIFY FREEZE PAGEVOLUME

UP

ON

DOWN

OFF

KEYSTONE

MY BUTTON

MUTE

1 2

For an HDMI TM signal

NORMAL 4:3 16:9 16:10 14:9 NATIVE

For a video signal, s-video signal or component video signal

4:3 16:9 16:10 14:9 NATIVE

For an input signal from the LAN, USB TYPE A or USB TYPE B port, or if there is no signal

16:10 (ﬁxed)

●ASPECT button does not work when no proper signal is inputted.

●NORMAL mode keeps the original aspect ratio setting.

●The on-screen menu might be displayed outside of the image display area depending on the adjustment value of the ASPECT, D-ZOOM, KEYSTONE and KEYSTONE. Changing the values of ASPECT, D-ZOOM,

KEYSTONE and KEYSTONE may ﬁx the symptom.

23

Image 25

Dukane 8107HWI Searching an input signal, Selecting an aspect ratio, For a computer signal, For an Hdmi TM signal

Contents

Model 8107HWI Page Projector About this manualThank you for purchasing this projector Trademark acknowledgment Contents Checking the contents of package Features Projector Part namesHOT Small Buttons Focus +/- buttons Control panel STANDBY/ON buttonHdmi Computer IN2 1415 Computer button Down button Volume + buttonMY Button 1 button MY Button 2 button Keystone button Zoom button Zoom + button Position button 26 Arrangement Setting up Arrangement Connecting with your devices VCR/DVD/Blu-ray Disc Player Computer About Plug-and-Play capability Connecting with your devices USB storage Device Monitor Microphone system Hdmi Access point Computer Using the security bar and slot Connecting to a power supplySecurity bar Anti-theft chain or wire Security slot Using the cable cover Installing the batteries Remote controlAbout the remote control signal Hitachi MAXELL, Part No.LR6 or R6P Using as a simple PC mouse & keyboard Changing the frequency of remote control signalUSB Type B port Interactive pen Installing the batteryExchanging the tip of the pen Hitachi MAXELL, Part No. LR03 Turning on the power Power on/offPower indicator STANDBY/ON button Turning off the power Selecting an input signal Adjusting the volumeOperating Temporarily muting the sound Computer button Press the MY Source / DOC. Camera button onVideo button MY Source For a computer signal Searching an input signalFor an Hdmi TM signal Selecting an aspect ratio Adjusting the zoom and focus Adjusting the projectors elevatorZoom button Zoom + button For a video signal and s-video signal Using the automatic adjustment featureFor a component video signal Focus button Correcting the keystone distortions Adjusting the positionPosition button Keystone button Magnify ON/OFF button Using the magnify feature Temporarily blanking the screen Temporarily freezing the screenFreeze button Blank button ESC button Reset button Using the menu functionAdvanced Menu Enter button Indication Meaning Indication in OSD On Screen Display Interactive DescriptionAspect Zoom ECO Mode Picture ModeReset Mirror Interactive menu Brightness Picture menuContrast Gamma LOW Custom MIDCustom Color Presentation SharpnessOFF Active Iris For an Hdmitm signal For a computer signalImage menu Selected will reset the H Position to the default setting Signal, the range of this adjustment depends on Over ScanPosition USB Type B or Hdmi port Auto Adjust PhaseSize Execute TV Film OFF Input menuHigh MID LOW Video NR Hdmi Format Video FormatHdmi Range Computer Auto Sync on G OFFFrame Lock Resolution Shift Setup menuLeft MID Right No Input is Detected Sync is OUT of Range Invalid Scan Freq On OFF Perfect FIT Input button Normal Hinvert Vinvert Normal ECONormal Saving Audio menu VolumeSpeaker Audio Source Hdmi Audio MIC VolumeMIC Level High LOW English Français Deutsch Español Screen menu MyScreen Capturing error has occurred. Please try againMyScreen registration is ﬁnished Message MyScreen Lock Source Name Template Display Description Closed CaptionMode Channel Option menu Direct PowerComputer IN2 LAN USB Type a Video Video Hdmi USB Type B OFF Auto PowerMouse USB Display USB Type B Cancel Cancel OKLamp Time No Messenger Data appears MY Button Picture Mode Changes the Picture Mode Active Iris Changes the active iris modeZoom Turns the D-ZOOM mode on/off. When the D-ZOOM Mode is on, use the / cursor buttons to adjust FAN Speed ServiceGhost Filter Message Lens Door Lock KEY LockLens Door Open Lens Door Close 1NORMAL 2HIGH Remote FreqControl port Baud Rate Service Serial SettingsCommunication Type Parity Transmission Method Response Limit Time Information Factory Reset Network menu SetupDhcp Setup Gateway DefaultIP Address Subnet Projector Name AMX D.D MY Image Presenter QuitPresentation Multi PC Section SwitchingUser Name Guide Security menu PasswordEnter to the Security menu Security Turning off the MyScreen Password Turning on the MyScreen PasswordMyScreen Turning on the PIN Lock PIN LockTurning off the PIN Lock If you have forgotten your PIN code Turning on the Transition Detector Transition DetectorTurning off the Transition Detector Turning on the MY Text Password MY Text PasswordTurning off the MY Text Password Writing MY Text Interactive Function Presentation toolsSystem requirements Application Interactive Function Connection during use Preliminary preparation Using the pen Customizing the pen Basic pen operation Using StarBoard Software Supported storage media PC-LESS PresentationSupported format Supported ﬁle format Thumbnail menu Selected image Thumbnail images Thumbnail mode Operating by buttons or keys Setup menu for the selected imageDown Enter Input Operating by the menu on the Thumbnail screen PC-LESS Presentation Full Screen Mode Control Projector Software Slideshow mode Play Example of playlist.txt ﬁles Playlist Hardware and software requirement for computer USB DisplayUSB Port USB cable 1 piece Floating menu Right-Click menu Options window Replacing the lamp MaintenanceType number 456-8104HW Replacing the lamp Lamp warning High Voltage High Temperature Type number UX37191 Filter set Cleaning and replacing the air ﬁlterStitched side On next 100 Cleaning and replacing the air ﬁlter Hitachi MAXELL, part number CR2032 or CR2032H Replacing the internal clock battery101 102 Cleaning cloth Maintenance of the pen sensors horns Caring for the cabinet and remote controlMaintenance of the pen Inside of the projector 104 Other care There is no input signal TroubleshootingAn improper signal is input Related messages Button operation is not available Internal temperature is rising106 Regarding the indicator lamps There is a possibility that the interior portion It is time to clean the air ﬁlterHas become heated Lens door is not opened properly Resetting all settings Volume is adjusted to an extremely low level Signal cables are not correctly connectedAudio SOURCE/SPEAKER setting is not correct Mode selected for Hdmi Audio is not suitable Color Space setting is not suitable Color settings are not correctly adjustedProjector is operating in Eco mode Frame Lock function cannot work on the current Input signal Saving function is working Computer cannot start up in the current hardwareCommunication Type for the Control port is Set to Network Bridge Is the power of the projector turned on? Is the use of USB cables disabled?Is the USB cable connected correctly? Is the system started up in the correct sequence? Has the battery run out? This may be due to poor contact of the batteryAre you using more than one pen at the same time? Is the volume from the speaker of the projector too loud? Is the tip of the pen worn out? StarBoard Software ﬁles may be corrupted, orIs alignment of the pen position correctly performed? Is the projector inclined? Is a part of the image enlarged using the Magnify Function? Is the projector correctly installed?Is the computer image projected within the area Screen? End User License Agreement for the Projector Software Speciﬁcations117