About this manual, Projector | Dukane 8107HWI specs

Projector

+ ,

User's Manual (detailed)

Operating Guide

Thank you for purchasing this projector.

WARNING ►Before using this product, please read all manuals for this product. Be sure to read “Safety Guide” ﬁrst. After reading them, store them in a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

NOTICE This entry notices of fear of causing trouble.

Please refer to the pages written following this symbol.

NOTE • The information in this manual is subject to change without notice.

•The manufacturer assumes no responsibility for any errors that may appear in this manual.

•The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

•Mac® is a registered trademark of Apple Inc.

•Windows®, DirectX®, DirectDraw® and Direct3D® are registered trademarks of Microsoft Corporation in the U.S. and/or other countries.

•VESA and DDC are trademarks of the Video Electronics Standard Association.

•HDMI, the HDMI logo, and High-Deﬁnition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

•Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas.

•Blu-ray DiscTM and Blu-rayTMare trademarks of Blu-ray Disc Association.

•StarBoard® is a registered trademark of Hitachi Solutions, Ltd. in Japan and other countries.

All other trademarks are the properties of their respective owners.

1

Image 3

Dukane 8107HWI user manual About this manual, Projector, Thank you for purchasing this projector, Trademark acknowledgment

Contents

Model 8107HWI Page Trademark acknowledgment About this manualProjector Thank you for purchasing this projector Contents Checking the contents of package Features Small Part namesProjector HOT 1415 Control panel STANDBY/ON buttonButtons Focus +/- buttons Hdmi Computer IN2 Zoom button Zoom + button Position button 26 Down button Volume + buttonComputer button MY Button 1 button MY Button 2 button Keystone button Arrangement Setting up Arrangement Connecting with your devices VCR/DVD/Blu-ray Disc Player Computer About Plug-and-Play capability Connecting with your devices USB storage Device Monitor Microphone system Hdmi Access point Computer Security slot Connecting to a power supplyUsing the security bar and slot Security bar Anti-theft chain or wire Using the cable cover Hitachi MAXELL, Part No.LR6 or R6P Remote controlInstalling the batteries About the remote control signal Changing the frequency of remote control signal Using as a simple PC mouse & keyboardUSB Type B port Hitachi MAXELL, Part No. LR03 Installing the batteryInteractive pen Exchanging the tip of the pen STANDBY/ON button Power on/offTurning on the power Power indicator Turning off the power Temporarily muting the sound Adjusting the volumeSelecting an input signal Operating MY Source Press the MY Source / DOC. Camera button onComputer button Video button Selecting an aspect ratio Searching an input signalFor a computer signal For an Hdmi TM signal Zoom + button Adjusting the projectors elevatorAdjusting the zoom and focus Zoom button Focus button Using the automatic adjustment featureFor a video signal and s-video signal For a component video signal Keystone button Adjusting the positionCorrecting the keystone distortions Position button Magnify ON/OFF button Using the magnify feature Blank button Temporarily freezing the screenTemporarily blanking the screen Freeze button Enter button Using the menu functionESC button Reset button Advanced Menu Indication Meaning Indication in OSD On Screen Display Zoom DescriptionInteractive Aspect Mirror Picture ModeECO Mode Reset Interactive menu Gamma Picture menuBrightness Contrast Color Custom MIDLOW Custom Active Iris SharpnessPresentation OFF For a computer signal For an Hdmitm signalImage menu USB Type B or Hdmi port Signal, the range of this adjustment depends on Over ScanSelected will reset the H Position to the default setting Position Execute PhaseAuto Adjust Size Video NR Input menuTV Film OFF High MID LOW Video Format Hdmi FormatHdmi Range Auto Sync on G OFF ComputerFrame Lock Resolution No Input is Detected Sync is OUT of Range Invalid Scan Freq Setup menuShift Left MID Right On OFF Perfect FIT Input button Normal ECO Normal Hinvert VinvertNormal Saving Audio Source VolumeAudio menu Speaker High LOW MIC VolumeHdmi Audio MIC Level English Français Deutsch Español Screen menu Capturing error has occurred. Please try again MyScreenMyScreen registration is ﬁnished Message MyScreen Lock Source Name Template Channel Description Closed CaptionDisplay Mode Direct Power Option menuComputer IN2 LAN USB Type a Video Video Hdmi USB Type B USB Type B Auto PowerOFF Mouse USB Display Cancel OK CancelLamp Time No Messenger Data appears MY Button Mode is on, use the / cursor buttons to adjust Active Iris Changes the active iris modePicture Mode Changes the Picture Mode Zoom Turns the D-ZOOM mode on/off. When the D-ZOOM Filter Message ServiceFAN Speed Ghost Lens Door Close KEY LockLens Door Lock Lens Door Open Remote Freq 1NORMAL 2HIGHControl port Parity Serial SettingsBaud Rate Service Communication Type Transmission Method Response Limit Time Information Factory Reset Setup Network menuDhcp Subnet DefaultSetup Gateway IP Address Projector Name AMX D.D MY Image Quit PresenterPresentation Section Switching Multi PCUser Name Guide Security PasswordSecurity menu Enter to the Security menu Turning on the MyScreen Password Turning off the MyScreen PasswordMyScreen If you have forgotten your PIN code PIN LockTurning on the PIN Lock Turning off the PIN Lock Transition Detector Turning on the Transition DetectorTurning off the Transition Detector MY Text Password Turning on the MY Text PasswordTurning off the MY Text Password Writing MY Text Application Presentation toolsInteractive Function System requirements Interactive Function Connection during use Preliminary preparation Using the pen Customizing the pen Basic pen operation Using StarBoard Software Supported ﬁle format PC-LESS PresentationSupported storage media Supported format Thumbnail menu Selected image Thumbnail images Thumbnail mode Enter Input Setup menu for the selected imageOperating by buttons or keys Down Operating by the menu on the Thumbnail screen PC-LESS Presentation Full Screen Mode Control Projector Software Slideshow mode Play Example of playlist.txt ﬁles Playlist USB Display Hardware and software requirement for computerUSB Port USB cable 1 piece Floating menu Right-Click menu Options window Maintenance Replacing the lampType number 456-8104HW Replacing the lamp Lamp warning High Voltage High Temperature Cleaning and replacing the air ﬁlter Type number UX37191 Filter setStitched side On next 100 Cleaning and replacing the air ﬁlter Replacing the internal clock battery Hitachi MAXELL, part number CR2032 or CR2032H101 102 Cleaning cloth Inside of the projector Caring for the cabinet and remote controlMaintenance of the pen sensors horns Maintenance of the pen 104 Other care Related messages TroubleshootingThere is no input signal An improper signal is input Internal temperature is rising Button operation is not available106 Regarding the indicator lamps Lens door is not opened properly It is time to clean the air ﬁlterThere is a possibility that the interior portion Has become heated Resetting all settings Mode selected for Hdmi Audio is not suitable Signal cables are not correctly connectedVolume is adjusted to an extremely low level Audio SOURCE/SPEAKER setting is not correct Frame Lock function cannot work on the current Input signal Color settings are not correctly adjustedColor Space setting is not suitable Projector is operating in Eco mode Set to Network Bridge Computer cannot start up in the current hardwareSaving function is working Communication Type for the Control port is Is the system started up in the correct sequence? Is the use of USB cables disabled?Is the power of the projector turned on? Is the USB cable connected correctly? Is the volume from the speaker of the projector too loud? This may be due to poor contact of the batteryHas the battery run out? Are you using more than one pen at the same time? Is the projector inclined? StarBoard Software ﬁles may be corrupted, orIs the tip of the pen worn out? Is alignment of the pen position correctly performed? Is the projector correctly installed? Is a part of the image enlarged using the Magnify Function?Is the computer image projected within the area Screen? Speciﬁcations End User License Agreement for the Projector Software117