Manuals / Paradise / Home Audio / Stereo Amplifier

Paradise RA 5785 manual Connector Pin-Outs, 1 Unit weights typical, Model Number, Weight, Units

Models: RA 5785

1 82

Download 82 pages 33.99 Kb

Page 14

Table 2-1: Unit weights (typical)

Table 2-1: Unit weights (typical)

Model Number	Weight	Units
HPACC3075AC_XXXX	26.0 (11.8)	lbs. (kg)

HPACC3100AC_XXXX	26.0 (11.8)	lbs. (kg)
HPAXX3050AC_XXXX	25.5 (11.6)	lbs. (kg)

HPAXX3075AC_XXXX	25.5 (11.6)	lbs. (kg)
HPAXX3100AC_XXXX	25.5 (11.6)	lbs. (kg)

HPAXX3175AC_XXXX	25.5 (11.6)	lbs. (kg)
HPAKU3050AC_XXXX	24.5 (11.1)	lbs. (kg)

HPAKU3080AC_XXXX	24.5 (11.1)	lbs. (kg)

2.2 Connector Pin-Outs

The Mini Compact Outdoor SSPA utilizes a variety of connectors for communication with the amplifier.

2.2.1 RF In (J1) [Type N (F)]

The RF Input signal is applied to J1, which is a type N female connector. The Mini Compact Outdoor SSPA has a default maximum nominal gain of 75 dB minimum. Therefore the maximum input signal required to saturate the amplifier can be calculated as:

Input Power = Psat – 75 dB

For example, if a 50 W Ku-Band Mini Compact Outdoor amplifier is used in a system it has a Psat = 47.0 dBm. Therefore the maximum input power should be limited to -28 dBm. Slightly higher input power levels will not damage the amplifier but will result in higher levels of distortion in the output signal.

WARNING! The maximum input level should be limited to +15 dBm to avoid damaging the amplifier.

2.2.2 RF Out (J2)

The amplifier’s output is brought out through the waveguide port, J2. Caution should be observed here to make sure that the antenna or a suitable termination is connected to this port before operating the amplifier. The amplifier is protected against full reflection but dangerous levels of microwave energy can be present at this port.

Ku-Band amplifiers have a WR-75 Grooved Flange while the C-Band and X-Band amplifiers have CPR style grooved flanges (CPR-137G for C-Band; CPR-112G for X-Band). An isolator is provided at the output flange with a termination capable of handling full reflected output power.

WARNING! Never look directly into the RF output waveguide.

14

208143 REV -

Operations Manual, HPA3, Mini Compact Outdoor SSPA

Image 14

Paradise RA 5785 Connector Pin-Outs, 1 Unit weights typical, Model Number, Weight, Units, RF In J1 Type N F, RF Out J2

Contents

Solid State Power Amplifier Operations Manual Mini Compact Outdoor208143 REV Section 2 Installation Table of ContentsTable of Contents Section 1 General InformationSection 4 L-BandOperation Section 5 Performance TestsSection 7 Redundant System Operation Section 6 Maintenance and TroubleshootingSection 8 Remote Control Interface Appendix A DocumentationFigures Tables THIS PAGE INTENTIONALLY LEFT BLANK 208143 REV1.0 Introduction 1.2SpecificationsSection 1 General Information 1.1 Description1.4 Equipment Supplied 1.5Safety Considerations1.3 Inspection 1.5.1 High Voltage HazardsNever look directly into the RF output waveguide THIS PAGE INTENTIONALLY LEFT BLANK 208143 REV2.0 Introduction Section 2 Installation2.1 Dimensions and Weight Weight 2.2 Connector Pin-OutsTable 2-1 Unit weights typical Model Number2.2.4 Monitor & Control Port J4 MS3112E18-32S 2.2.4.1 Alarms on J42.2.3 RF Output Sample Port J3 Type N F Pin # Table 2-2 J4 Monitor & Control Port Pin-OutsSignal Type2.2.4.2 Serial I/O Control J4 2.2.6 Switch Port J6 MS3112E10-6STable 2-4 J6 Switch Port Pin-Outs 2.2.5 Link Port J5 MS3112E10-6STable 2-7 J8 Auxiliary Power Port Pin-Outs Table 2-6 Power Requirements2.2.8 Auxiliary Power Port J8 MS3112E10-6S 2.2.7 AC In J7 MS3102R16-10P2.2.9 Chassis Ground Pin 2.3 Physical Features2.3.1 Summary Alarm Indicator 2.3.2 Removable Fan TrayTable 2-8 Universal CO Mounting Kit Parts List 2.4 Installation2.4.1 Safety Considerations 2.4.2 InspectionFigure 2-3 Attach Mounting Supports to Unit 2.4.3 InstallationFigure 2-4 Install All-Threadstud 208143 REVFigure 2-5 Mount Unit to Antenna Boom 208143 REV3.0 Introduction 3.0.1 Remote Communications ConnectionsSection 3 Quick Start and Operation 3.1 Quick Start Cables Figure 3-6 RS232 Quick Start Cable 3.2.1 Set PC Configuration3.2 Quick Start Operation 2.Click on the Network and Sharing Center link 3.2.2Quick Start Ethernet ConnectionWeb password paradise Read Community public 3.Click on the Local Area Connection linkBaud rate Amplifier is un-muted 3.2.3 Quick Start RS-232ConnectionSerial Interface RS-232Communication 3.3Universal M&C Operation Figure 3-7 Universal M&C Add Unit menu3.3.1 Universal M&C Status Window 3.3.1.1 Signal IndicatorsFigure 3-9 Universal M&C Status Window 3.3.1.2 Fault Status Indicators 208143 REV3.3.1.5 RF Power Indicator 3.3.1.3 Voltage, Current and Temperature Display3.3.1.4 Gain Adjustment 3.3.1.6 Reference SourcePower Up Settings 3.3.2 Universal M&C Settings WindowFigure 3-10 Universal M&C, Settings 208143 REVFigure 3-11 Spare Fault Wizard 3.3.3 IP Setup Figure 3-12 Universal M&C, IP SetupFigure 3-14 Example, Log entry 3.3.4 Universal M&C PreferencesFigure 3-13 Preferences Window 208143 REV3.4 Web-basedM&C 208143 REV3.4.1 Navigating the Web M&C Figure 3-17 Enter password default is “paradise”Figure 3-18 Status and Faults window descriptions Red indicates aSelected Protocol Selected Baud Rate Figure 3-20 General Settings window descriptions “LNB Current” Figure 3-21 Fault Settings window descriptions“Major Fault” or ThresholdSection 4 L-BandOperation Band Power Level Watts Frequency Sub BandConfiguration Modifiers System Configuration 4.0 Block Up Converter Overview4.1 Converter Features Table 4-1 BUC Frequency Specifications4.3 Smart Reference Technology Table 4-2 BUC RF output phase noise specification4.2 Theory of Operation 4.4 FSK Monitor and Control 4.6 IFL Cable Considerations 4.5 Typical System ConfigurationTable 4-3 Common Coaxial Cable Characteristics THIS PAGE INTENTIONALLY LEFT BLANK 208143 REV5.1 Standard tests Section 5 Performance Tests5.0 Introduction 5.1.1 Swept Gain5.1.4 Output Return Loss 5.1.2 Spurious5.1.3 Input Return Loss 208143 REV208143 REV 5.1.6 Power Requirements5.1.5 Intermodulation Distortion 5-3,Item 5.1.10 I/O Test 5.1.7 Earth Ground5.1.8 Sample Port 5.1.11 Ethernet5.2.1 Reference Lock 5.2.3 Phase Noise5.2 Tests for units with integrated BUC 5.2.2 FSK5.3 Optional Tests 5.3.2 Group Delay5.3.4 Noise Power 5.3.1 Noise Figure6.2 Fan Removal and Heatsink Cleaning Section 6 Maintenance and Troubleshooting6.1 Cooling System Maintenance 6.2.1 Fan Replacement6.3.2 Unit powers on, LED lamp glows red 6.3 Troubleshooting guide6.3.1 Unit doesn’t power up Possible solutions 208143 REVTHIS PAGE INTENTIONALLY LEFT BLANK 208143 REV7.0 Redundant System Concepts Section 7 Redundant System Configurationsand output waveguide switch 7.1 1 1 Redundant SystemsFigure 7-3 1 1 Redundant System with L Band input Figure 7-4 1 2 Redundant System Block Diagram7.2 1 2 Redundant Systems Section 8 Remote Control Interface 8.0 Serial Protocol OverviewTable 8-1 Interface Selection DATA 8.1 Serial communicationHEADER TRAILER8.1.2 Data Packet 8.1.2.3 Command8.1.1.3 Source Address HEADER 4 bytesCommand Byte Value Table 8-2 Command Byte ValuesCommand Name 8.1.2.4 Data TagPossible Cause Table 8-4Error Status BytesError Code name ValueHEADER 8.1.4 Timing issues8.1.3 Trailer Packet 4 bytesTable 8-6 Response Frame Structure 8.1.5 Serial Communications ProtocolTable 8-5 Request Frame Structure Byte position# Bytes Table 8-7 System Settings Data ValuesData DescriptionTable 8-7 System Settings Data Values continued Table 8-8:System Threshold Data Values# Bytes Table 8-9 System Condition AddressingData Description8.2.2 IPNet Interface 8.2 Ethernet Interface8.2.1 Overview 8.2.2.1 General ConceptFigure 8-6 UDP Redirect Frame Example UDP HeaderSSPA Serial Protocol Frame OSI Layer8.2.2.2 Setting IPNet interface 8.2.2.3 Troubleshooting IP connectivity8.2.3 SNMP interface 8.2.3.1 SNMP MIB tree 8.2.3.2 Description of MIB entities 208143 REVValue OID settingIndex/settingValuesettingTextValue DescriptionsettingTextValue DescriptionthresholdIndex Table 8-12 Detailed ThresholdsTable 8-13 Detailed Conditions thresholdTextValue8.3 M&C via SNMP Figure 8-7 Universal M&C, IP Setup tabFigure 8-8 Universal M&C, Settings tab 8.3.1 Connecting to a MIB browser Figure 8-9 GetIF Application Parameters TabAppendix A Documentation 208143 REV