Manuals / Paradise / Home Audio / Stereo Amplifier

Paradise RA 5785 manual 12 Universal M&C, IP Setup

Models: RA 5785

1 82

Download 82 pages 33.99 Kb

Page 34

3.3.3 IP Setup

[13] Fault Setups: The user may also adjust the Spare, Auxiliary, BUC, Fiber, and Forward RF Fault Status and Handling via the appropriate pull-down menus on the Settings Window.

[Type] Fault Handling: Selects whether the associated fault should be a major or minor fault, and whether the fault should mute the unit. A minor fault will trigger a Spare/Auxiliary/BUC/Forward RF Fault alarm but not trigger a Summary Fault. A major fault will trigger both an Spare/ Auxiliary/BUC/Forward RF Fault and a Summary Fault.

[Type] Fault Status: Determines if the associated fault input should be ignored or enabled (either Logic High or Logic Low for Auxiliary Fault or Fiber Fault).

Forward RF Threshold: Allows the user to assign the threshold at which a Forward RF Fault will be triggered.

3.3.3 IP Setup

If the user wishes to set up the networked Mini Compact Outdoor SSPA with custom IP settings, the internal IP settings need to be modified. Click on the IP Setup Tab. See Figure 3-12.

•The SSPA will use the default settings until the unit is reset by removing its AC power. Unplug the Quick Start cable from the M&C connector. (If the unit is restarted with the Quick Start cable connected, it will always come up with default IP settings). Apply power to the SSPA. Re-plug the Quick Start cable into J4, and check connectivity with the custom IP settings.

•Make sure that the Protocol Select setting in the Settings tab of the Universal M&C is set to IPNET, as shown in Figure 3-10.

•If custom IP settings will be used in normal operation, do not use the Quick Start cable (207755) that was shipped with the unit. The user will need to construct an IP cable with connections to J4 as shown in Figure 3-2. In this configuration, the SSPA will always use the saved communication control settings rather than the default configuration.

Modify IP Settings

to work with your network.

Click

“Change IP Settings”

Figure 3-12: Universal M&C, IP Setup

34

208143 REV -

Operations Manual, HPA3, Mini Compact Outdoor SSPA

Image 34

Paradise RA 5785 manual 12 Universal M&C, IP Setup

Contents

Solid State Power Amplifier Operations Manual Mini Compact Outdoor208143 REV Section 2 Installation Table of ContentsTable of Contents Section 1 General InformationSection 4 L-BandOperation Section 5 Performance TestsSection 7 Redundant System Operation Section 6 Maintenance and TroubleshootingSection 8 Remote Control Interface Appendix A DocumentationFigures Tables THIS PAGE INTENTIONALLY LEFT BLANK 208143 REV1.0 Introduction 1.2SpecificationsSection 1 General Information 1.1 Description1.4 Equipment Supplied 1.5Safety Considerations1.3 Inspection 1.5.1 High Voltage HazardsNever look directly into the RF output waveguide THIS PAGE INTENTIONALLY LEFT BLANK 208143 REV2.1 Dimensions and Weight Section 2 Installation2.0 Introduction Weight 2.2 Connector Pin-OutsTable 2-1 Unit weights typical Model Number2.2.3 RF Output Sample Port J3 Type N F 2.2.4.1 Alarms on J42.2.4 Monitor & Control Port J4 MS3112E18-32S Pin # Table 2-2 J4 Monitor & Control Port Pin-OutsSignal Type2.2.4.2 Serial I/O Control J4 2.2.6 Switch Port J6 MS3112E10-6STable 2-4 J6 Switch Port Pin-Outs 2.2.5 Link Port J5 MS3112E10-6STable 2-7 J8 Auxiliary Power Port Pin-Outs Table 2-6 Power Requirements2.2.8 Auxiliary Power Port J8 MS3112E10-6S 2.2.7 AC In J7 MS3102R16-10P2.2.9 Chassis Ground Pin 2.3 Physical Features2.3.1 Summary Alarm Indicator 2.3.2 Removable Fan TrayTable 2-8 Universal CO Mounting Kit Parts List 2.4 Installation2.4.1 Safety Considerations 2.4.2 InspectionFigure 2-3 Attach Mounting Supports to Unit 2.4.3 InstallationFigure 2-4 Install All-Threadstud 208143 REVFigure 2-5 Mount Unit to Antenna Boom 208143 REVSection 3 Quick Start and Operation 3.0.1 Remote Communications Connections3.0 Introduction 3.1 Quick Start Cables 3.2 Quick Start Operation 3.2.1 Set PC ConfigurationFigure 3-6 RS232 Quick Start Cable 2.Click on the Network and Sharing Center link 3.2.2Quick Start Ethernet ConnectionWeb password paradise Read Community public 3.Click on the Local Area Connection linkSerial Interface RS-232Communication 3.2.3 Quick Start RS-232ConnectionBaud rate Amplifier is un-muted 3.3Universal M&C Operation Figure 3-7 Universal M&C Add Unit menuFigure 3-9 Universal M&C Status Window 3.3.1.1 Signal Indicators3.3.1 Universal M&C Status Window 3.3.1.2 Fault Status Indicators 208143 REV3.3.1.5 RF Power Indicator 3.3.1.3 Voltage, Current and Temperature Display3.3.1.4 Gain Adjustment 3.3.1.6 Reference SourcePower Up Settings 3.3.2 Universal M&C Settings WindowFigure 3-10 Universal M&C, Settings 208143 REVFigure 3-11 Spare Fault Wizard 3.3.3 IP Setup Figure 3-12 Universal M&C, IP SetupFigure 3-14 Example, Log entry 3.3.4 Universal M&C PreferencesFigure 3-13 Preferences Window 208143 REV3.4 Web-basedM&C 208143 REV3.4.1 Navigating the Web M&C Figure 3-17 Enter password default is “paradise”Figure 3-18 Status and Faults window descriptions Red indicates aSelected Protocol Selected Baud Rate Figure 3-20 General Settings window descriptions “LNB Current” Figure 3-21 Fault Settings window descriptions“Major Fault” or ThresholdSection 4 L-BandOperation Band Power Level Watts Frequency Sub BandConfiguration Modifiers System Configuration 4.0 Block Up Converter Overview4.1 Converter Features Table 4-1 BUC Frequency Specifications4.2 Theory of Operation Table 4-2 BUC RF output phase noise specification4.3 Smart Reference Technology 4.4 FSK Monitor and Control Table 4-3 Common Coaxial Cable Characteristics 4.5 Typical System Configuration4.6 IFL Cable Considerations THIS PAGE INTENTIONALLY LEFT BLANK 208143 REV5.1 Standard tests Section 5 Performance Tests5.0 Introduction 5.1.1 Swept Gain5.1.4 Output Return Loss 5.1.2 Spurious5.1.3 Input Return Loss 208143 REV5.1.5 Intermodulation Distortion 5.1.6 Power Requirements208143 REV 5-3,Item 5.1.10 I/O Test 5.1.7 Earth Ground5.1.8 Sample Port 5.1.11 Ethernet5.2.1 Reference Lock 5.2.3 Phase Noise5.2 Tests for units with integrated BUC 5.2.2 FSK5.3 Optional Tests 5.3.2 Group Delay5.3.4 Noise Power 5.3.1 Noise Figure6.2 Fan Removal and Heatsink Cleaning Section 6 Maintenance and Troubleshooting6.1 Cooling System Maintenance 6.2.1 Fan Replacement6.3.1 Unit doesn’t power up 6.3 Troubleshooting guide6.3.2 Unit powers on, LED lamp glows red Possible solutions 208143 REVTHIS PAGE INTENTIONALLY LEFT BLANK 208143 REV7.0 Redundant System Concepts Section 7 Redundant System Configurationsand output waveguide switch 7.1 1 1 Redundant Systems7.2 1 2 Redundant Systems Figure 7-4 1 2 Redundant System Block DiagramFigure 7-3 1 1 Redundant System with L Band input Section 8 Remote Control Interface 8.0 Serial Protocol OverviewTable 8-1 Interface Selection DATA 8.1 Serial communicationHEADER TRAILER8.1.2 Data Packet 8.1.2.3 Command8.1.1.3 Source Address HEADER 4 bytesCommand Byte Value Table 8-2 Command Byte ValuesCommand Name 8.1.2.4 Data TagPossible Cause Table 8-4Error Status BytesError Code name ValueHEADER 8.1.4 Timing issues8.1.3 Trailer Packet 4 bytesTable 8-6 Response Frame Structure 8.1.5 Serial Communications ProtocolTable 8-5 Request Frame Structure Byte position# Bytes Table 8-7 System Settings Data ValuesData DescriptionTable 8-7 System Settings Data Values continued Table 8-8:System Threshold Data Values# Bytes Table 8-9 System Condition AddressingData Description8.2.2 IPNet Interface 8.2 Ethernet Interface8.2.1 Overview 8.2.2.1 General ConceptFigure 8-6 UDP Redirect Frame Example UDP HeaderSSPA Serial Protocol Frame OSI Layer8.2.2.2 Setting IPNet interface 8.2.2.3 Troubleshooting IP connectivity8.2.3 SNMP interface 8.2.3.1 SNMP MIB tree 8.2.3.2 Description of MIB entities 208143 REVValue OID settingIndex/settingValuesettingTextValue DescriptionsettingTextValue DescriptionthresholdIndex Table 8-12 Detailed ThresholdsTable 8-13 Detailed Conditions thresholdTextValueFigure 8-8 Universal M&C, Settings tab Figure 8-7 Universal M&C, IP Setup tab8.3 M&C via SNMP 8.3.1 Connecting to a MIB browser Figure 8-9 GetIF Application Parameters TabAppendix A Documentation 208143 REV