Manuals / Paradise / Home Audio / Stereo Amplifier

Paradise RA 5785 manual 2 J4 Monitor & Control Port Pin-Outs, Pin #, Signal, Type, Function

Models: RA 5785

1 82

Download 82 pages 33.99 Kb

Page 16

Table 2-2: J4 Monitor & Control Port Pin-Outs

Table 2-2: J4 Monitor & Control Port Pin-Outs

	Pin #	Signal	Type	Function	Notes
					Unit powers up muted. This line
	B	Mute Input	Closure to Ground	Disables DC power to SSPA	must be pulled to ground (V or d)
					to enable amplifier.
	P	Auxiliary Input	Closure to Ground	Auxiliary Fault Input
	L			Closed on Fault	L-a: normally open
	a	Summary Alarm	Form C Relay	Common
	b			Open on Fault	a-b: normally closed
	N			Closed on Fault	N-Z: normally open
	Z	Auxiliary Alarm	Form C Relay	Common
	M			Open on Fault	Z-M: normally closed
	G	Auxiliary Alarm	Open Collector	High on Fault	Requires external pull-up

	W	10 Base-T Tx-			Refer to M&C Section
	H	10 Base-T Rx+			Refer to M&C Section

	J	10 Base-T Rx-			Refer to M&C Section
	X	10 Base-T Tx+			Refer to M&C Section

	S	Reserved			Make no connection
	R	Reserved			Make no connection

	A	Reserved			Make no connection
	f	Reserved			Make no connection

	D	RS232/RS485	Closure to Ground	Selects Serial	Default is RS485; Pull to ground
		Select		Communication	(d) to enable RS232
	E	RS485 TX- or	Serial TX Output	Serial Link Data Port	Refer to M&C Section
	E	RS232 OUT	Serial TX Output	Serial Link Data Port	Refer to M&C Section
		RS232 OUT

	F	RS485 RX- or	Serial RX Input	Serial Link Data Port	Refer to M&C Section
	F	RS232 IN	Serial RX Input	Serial Link Data Port	Refer to M&C Section
		RS232 IN
	T	RS485 TX+	Serial TX Output	Serial Link Data Port	Refer to M&C Section

	U	RS485 RX+	Serial RX Input	Serial Link Data Port	Refer to M&C Section
	V	Chassis Ground	Signal Ground	Common Signal Return

	d	Isolated Ground	Signal Ground	Isolated Comm Ground	Ground for Signals D, E & F
	j	Interface	Closure to Ground	Select Baud Rate & Protocol	Refer to M&C Section
	j	Select 0	Closure to Ground	Select Baud Rate & Protocol	Refer to M&C Section
		Select 0
	e	Interface	Closure to Ground	Select Baud Rate & Protocol	Refer to M&C Section
	e	Select 1	Closure to Ground	Select Baud Rate & Protocol	Refer to M&C Section
		Select 1
	g	PGM Switch		Flash Firmware Port	Reserved for Programming

	c	PGM CLK		Flash Firmware Port	Reserved for Programming
	K	PGM-Sout		Flash Firmware Port	Reserved for Programming

	Y	PGM-Sin		Flash Firmware Port	Reserved for Programming
	h	PGM +5V		Flash Firmware Port	Reserved for Programming

	C	PGM Enable		Flash Firmware Port	Reserved for Programming

16

208143 REV -

Operations Manual, HPA3, Mini Compact Outdoor SSPA

Image 16

Paradise RA 5785 manual 2 J4 Monitor & Control Port Pin-Outs, Pin #, Signal, Type, Function

Contents

Solid State Power Amplifier Operations Manual Mini Compact Outdoor208143 REV Table of Contents Table of ContentsSection 2 Installation Section 1 General InformationSection 4 L-BandOperation Section 5 Performance TestsSection 6 Maintenance and Troubleshooting Section 8 Remote Control InterfaceSection 7 Redundant System Operation Appendix A DocumentationFigures Tables THIS PAGE INTENTIONALLY LEFT BLANK 208143 REV1.2Specifications Section 1 General Information1.0 Introduction 1.1 Description1.5Safety Considerations 1.3 Inspection1.4 Equipment Supplied 1.5.1 High Voltage HazardsNever look directly into the RF output waveguide THIS PAGE INTENTIONALLY LEFT BLANK 208143 REV2.1 Dimensions and Weight Section 2 Installation2.0 Introduction 2.2 Connector Pin-Outs Table 2-1 Unit weights typicalWeight Model Number2.2.3 RF Output Sample Port J3 Type N F 2.2.4.1 Alarms on J42.2.4 Monitor & Control Port J4 MS3112E18-32S Table 2-2 J4 Monitor & Control Port Pin-Outs SignalPin # Type2.2.6 Switch Port J6 MS3112E10-6S Table 2-4 J6 Switch Port Pin-Outs2.2.4.2 Serial I/O Control J4 2.2.5 Link Port J5 MS3112E10-6STable 2-6 Power Requirements 2.2.8 Auxiliary Power Port J8 MS3112E10-6STable 2-7 J8 Auxiliary Power Port Pin-Outs 2.2.7 AC In J7 MS3102R16-10P2.3 Physical Features 2.3.1 Summary Alarm Indicator2.2.9 Chassis Ground Pin 2.3.2 Removable Fan Tray2.4 Installation 2.4.1 Safety ConsiderationsTable 2-8 Universal CO Mounting Kit Parts List 2.4.2 Inspection2.4.3 Installation Figure 2-4 Install All-ThreadstudFigure 2-3 Attach Mounting Supports to Unit 208143 REVFigure 2-5 Mount Unit to Antenna Boom 208143 REVSection 3 Quick Start and Operation 3.0.1 Remote Communications Connections3.0 Introduction 3.1 Quick Start Cables 3.2 Quick Start Operation 3.2.1 Set PC ConfigurationFigure 3-6 RS232 Quick Start Cable 3.2.2Quick Start Ethernet Connection Web password paradise Read Community public2.Click on the Network and Sharing Center link 3.Click on the Local Area Connection linkSerial Interface RS-232Communication 3.2.3 Quick Start RS-232ConnectionBaud rate Amplifier is un-muted 3.3Universal M&C Operation Figure 3-7 Universal M&C Add Unit menuFigure 3-9 Universal M&C Status Window 3.3.1.1 Signal Indicators3.3.1 Universal M&C Status Window 3.3.1.2 Fault Status Indicators 208143 REV3.3.1.3 Voltage, Current and Temperature Display 3.3.1.4 Gain Adjustment3.3.1.5 RF Power Indicator 3.3.1.6 Reference Source3.3.2 Universal M&C Settings Window Figure 3-10 Universal M&C, SettingsPower Up Settings 208143 REVFigure 3-11 Spare Fault Wizard 3.3.3 IP Setup Figure 3-12 Universal M&C, IP Setup3.3.4 Universal M&C Preferences Figure 3-13 Preferences WindowFigure 3-14 Example, Log entry 208143 REV3.4 Web-basedM&C 208143 REVFigure 3-17 Enter password default is “paradise” Figure 3-18 Status and Faults window descriptions3.4.1 Navigating the Web M&C Red indicates aSelected Protocol Selected Baud Rate Figure 3-20 General Settings window descriptions Figure 3-21 Fault Settings window descriptions “Major Fault” or“LNB Current” ThresholdBand Power Level Watts Frequency Sub Band Configuration Modifiers System ConfigurationSection 4 L-BandOperation 4.0 Block Up Converter Overview4.1 Converter Features Table 4-1 BUC Frequency Specifications4.2 Theory of Operation Table 4-2 BUC RF output phase noise specification4.3 Smart Reference Technology 4.4 FSK Monitor and Control Table 4-3 Common Coaxial Cable Characteristics 4.5 Typical System Configuration4.6 IFL Cable Considerations THIS PAGE INTENTIONALLY LEFT BLANK 208143 REVSection 5 Performance Tests 5.0 Introduction5.1 Standard tests 5.1.1 Swept Gain5.1.2 Spurious 5.1.3 Input Return Loss5.1.4 Output Return Loss 208143 REV5.1.5 Intermodulation Distortion 5.1.6 Power Requirements208143 REV 5.1.7 Earth Ground 5.1.8 Sample Port5-3,Item 5.1.10 I/O Test 5.1.11 Ethernet5.2.3 Phase Noise 5.2 Tests for units with integrated BUC5.2.1 Reference Lock 5.2.2 FSK5.3.2 Group Delay 5.3.4 Noise Power5.3 Optional Tests 5.3.1 Noise FigureSection 6 Maintenance and Troubleshooting 6.1 Cooling System Maintenance6.2 Fan Removal and Heatsink Cleaning 6.2.1 Fan Replacement6.3.1 Unit doesn’t power up 6.3 Troubleshooting guide6.3.2 Unit powers on, LED lamp glows red Possible solutions 208143 REVTHIS PAGE INTENTIONALLY LEFT BLANK 208143 REVSection 7 Redundant System Configurations and output waveguide switch7.0 Redundant System Concepts 7.1 1 1 Redundant Systems7.2 1 2 Redundant Systems Figure 7-4 1 2 Redundant System Block DiagramFigure 7-3 1 1 Redundant System with L Band input Section 8 Remote Control Interface 8.0 Serial Protocol OverviewTable 8-1 Interface Selection 8.1 Serial communication HEADERDATA TRAILER8.1.2.3 Command 8.1.1.3 Source Address8.1.2 Data Packet HEADER 4 bytesTable 8-2 Command Byte Values Command NameCommand Byte Value 8.1.2.4 Data TagTable 8-4Error Status Bytes Error Code namePossible Cause Value8.1.4 Timing issues 8.1.3 Trailer PacketHEADER 4 bytes8.1.5 Serial Communications Protocol Table 8-5 Request Frame StructureTable 8-6 Response Frame Structure Byte positionTable 8-7 System Settings Data Values Data# Bytes DescriptionTable 8-7 System Settings Data Values continued Table 8-8:System Threshold Data ValuesTable 8-9 System Condition Addressing Data# Bytes Description8.2 Ethernet Interface 8.2.1 Overview8.2.2 IPNet Interface 8.2.2.1 General ConceptUDP Header SSPA Serial Protocol FrameFigure 8-6 UDP Redirect Frame Example OSI Layer8.2.2.2 Setting IPNet interface 8.2.2.3 Troubleshooting IP connectivity8.2.3 SNMP interface 8.2.3.1 SNMP MIB tree 8.2.3.2 Description of MIB entities 208143 REVsettingIndex/settingValue settingTextValueValue OID DescriptionsettingTextValue DescriptionTable 8-12 Detailed Thresholds Table 8-13 Detailed ConditionsthresholdIndex thresholdTextValueFigure 8-8 Universal M&C, Settings tab Figure 8-7 Universal M&C, IP Setup tab8.3 M&C via SNMP 8.3.1 Connecting to a MIB browser Figure 8-9 GetIF Application Parameters TabAppendix A Documentation 208143 REV