Dhcp Relay with Proxy ARP Configuration Example | Paradyne 6302

4. DSL Router Configuration Examples

DHCP Relay with Proxy ARP Configuration Example

Core

Router

Customer Premises (CP)

	155.1.3.1
	DHCP 155.1.3.253		Console
	Server		Console
			Port
			Connection
	DSL		Ethernet
	WAN		Hub
	dsl1	DSL	eth1
	Unnumbered	DSL	155.1.3.254
	Unnumbered	Router	155.1.3.254
		Router

End-user

Systems

155.1.3.2

155.1.3.3

155.1.3.4

01-16612-02

In this DHCP Relay with Proxy ARP example:

The clients are using dynamic IP address assignment and use the core router as the next hop router (default gateway) in order to create the LAN extension configuration.

The DSL interface (dsl1) is unnumbered.

The clients, the Ethernet interface (eth1), and the core router interface are all on the same logical network.

IP Scoping must be disabled at the DSL card.

The DSL router is configured as a DHCP relay.

The commands and syntax for this example are:

ip routing enable

ifn address eth1 155.1.3.254 255.255.255.0 ifn address dsl1 unnumbered

ip route create upstream eth1 155.1.3.1 proxy arp eth1 enable

proxy arp dsl1 enable dhcp relay enable

dhcp relay address 155.1.3.253

NOTES:

—The ip routing enable command is only required when using firmware version 4.2.5 or higher.

—FUNI/MPOA (1483 routed) link encapsulation can be used with this configuration and the DSL card Models 8304, 8314, 8344, and 8374. Link encapsulation is configured on the DSL port. This link encapsulation must match the core network encapsulation type. The ip route create upstream and proxy arp dsl1 enable commands are not necessary when using FUNI/MPOA link encapsulation.

6300-A2-GB20-10

November 2003

4-11

Image 53

Paradyne 6302, 6341, 6301, 6342, 6371, 6351 manual Dhcp Relay with Proxy ARP Configuration Example

Contents

Hotwire DSL Routers Copyright 2003 Paradyne Corporation All rights reserved Contents Monitoring the DSL Router DSL Router Configuration Examples Command Line Interface Diagnostics and Troubleshooting DSL Router Terminal Emulation Configuration Defaults and Command Line ShortcutsTraps and MIBs Index Firmware Upgrade Contents November Document Purpose and Intended Audience About This Guide New Features for this Release Section Description Document Summary Document Number Document Title Product-Related Documents Convention Translation Document Conventions Xii DSL Technologies Supported Introduction to Hotwire DSL RoutersWhat is a Hotwire DSL Router? Optional Typical DSL Router SystemCentral Office CO Customer Premises CP IP routing with Hotwire DSL Router Features Management from an NMS using Snmp Service Subscriber Levels of Access Accessing the DSL RouterAccess Control to the DSL Router Changing Access Session Levels Local Console AccessConsole disable save Exit Admin enable Invalid Characters Value Ascii Hex Translation Setting Up the New User’s Login Password admin new password save Telnet AccessLocal console disabled by conflict message Telnet enable save Determining the Available Commands Determining the Current Access LevelTelnet login enable save Help List config Using the List CommandChanging the System Identity List Exiting from the System If accessing the DSL router ThenManually Logging Out Exit Automatically Logging Out When autologout is DSL Router’s Interfaces Configuring the DSL RouterDSL Router Configuration Overview Interface Identifiers Service Domain IP Address Assignments Simplified Network Topology Numbered DSL or Ethernet InterfaceUnnumbered DSL Interface IP Options Processing IP Routing Network Considerations Address Resolution Protocol ARP Proxy ARP Network Address Port Translation NAPT/PAT Network Address Translation NATBasic NAT Applications Supported by NAT Simultaneous Basic NAT and Napt Dynamic Host Configuration Protocol Dhcp Server Dhcp Relay Agent IP Protocol Type Filtering Security Land Bug/Smurf Attack Prevention Ethernet Type Filtering Routed vs. Bridged PDUs If Using This Network Model Then These DSL Cards Can Be Used PPPoE Client Support Routed Network Model Standard mode When the negotiated IP Address is assigned to Then Configuring the DSL Router Configuration Examples DSL Router Configuration Examples IP, IPX Basic Bridging Configuration Example Basic Routing Configuration Example NAT Mapping Public IP Addresses Private IP Addresses Basic NAT Configuration Example Commands and syntax for this example are Napt Mapping Public IP Addresses Private IP Addresses Napt Configuration Example DSL Router Configuration Examples Simultaneous Basic NAT and Napt Configuration Example DSL Router Configuration Examples Core Router 155.1.3.1 Console Port Connection Dhcp Relay with Proxy ARP Configuration Example Dhcp Server with Basic NAT Configuration Example PPPoE Client with Napt and Dhcp Server Configuration Example Downstream Router Configuration Example Customer Premises CP IP Passthrough Configuration Example DSL Router Configuration Examples November Monitoring the Router Monitoring the DSL Router Condition Status LED StatusFront Panel LEDs Clearing Statistics Interface StatusPerformance Statistics Reasons for Ethernet Interface eth1 Discarded Frames Reasons for Discarded Data Reasons for DSL Interface dsl1 Discarded Frames Reasons for IP Processing Discarded Packets Reasons for PPPoE Discarded Frames Reasons for Bridge Discarded Frames Reasons for PPP Discarded Frames Diagnostics and Troubleshooting Overview Diagnostics and TroubleshootingAlarms Inquiry Device Restart Syslog enable disable Syslog Commands 1System Log Show syslog Syslog ip ip-addr mgt srvc Syslog Commands 2Syslog port port-number Syslog level level Syslog Messages Level Description Event Syslog Events Ping Ping CommandSyslog Message Display Ping dest-ipmgt -x source-ip-l bytes -w time -ieth1 dsl1 Ping reply from x.x.x.x bytes of data=nn Ping Test ResultsPing reply from x.x.x.x Request Timed OUT Ping reply from x.x.x.x Destination Unreachable Example traceroute 135.300.41.8 -w 60 -i eth1 TraceRoute CommandTraceRoute Tracing route to TraceRoute Test ResultsOver a max. of nn Hops, with nnn Byte packet X.x Command Line Interface Capability Command Line Interface Syntax Conventions Command RecallNavigating the Router’s CLI CLI Commands Table A-1. Configuration Commands Configuration CommandsConfigure terminal factory Save Ethernet Frame Format Command RFC 1483 Encapsulation CommandTable A-2. RFP 1483 Encapsulation Command Table A-3. Ethernet Frame Format Command Examples ifn address dsl1 135.300.41.8 Ifn dsl1 primary Interface and Service Domain IP Address CommandsTable A-4. Interface and Service Domain IP Address Commands Table A-5. IP Routing Commands 1 IP Routing Commands Table A-5. IP Routing Commands 2 Bridge CommandsTable A-6. Bridge Commands 1 Bridge enable disable Table A-7. ARP Commands 1 ARP CommandsTable A-6. Bridge Commands 2 Table A-7. ARP Commands 2 Proxy ARP CommandTable A-8. Proxy ARP Command Proxy arp eth1 dsl1 enable disable Table A-9. NAT Commands 1 NAT Commands Nat timeout time Table A-9. NAT Commands 2Nat napt purge Nat napt map udp tcp server-ip port Nat napt delete udp tcp port Table A-9. NAT Commands 3Nat basic delete private-ip Table A-10. Dhcp Server Commands 1 Dhcp Server CommandsTable A-9. NAT Commands 4 Dhcp server router ip-address Table A-10. Dhcp Server Commands 2Dhcp server name domain name Dhcp server nameserver ip-addressip-address2 Table A-11. Dhcp Relay Agent Commands Dhcp Relay Agent CommandsDhcp relay enable disable Dhcp relay address ip-address Table A-12. IP Packet Processing Commands IP Packet Processing CommandsIP multicast enable disable IP routing enable disable Table A-13. PPPoE Client Commands 1 PPPoE Client CommandsPppoe enable disable Ppp ip eth1 dsl1 passthrough mask no-dns From previous Table A-13. PPPoE Client Commands 2Ppp authentication chap pap both none Ppp username username Table A-13. PPPoE Client Commands 3 Table A-14. Telnet Commands 1 Telnet Commands Telnet timeout time Table A-14. Telnet Commands 2Telnet keep-alive enable disable Telnet keep-alive timeout time Clearing Statistics Command Traps CommandTable A-15. Traps Command Table A-16. Clearing Statistics Command Table A-17. Show Commands 1 Show CommandsShow alarms Show arp timeout Show config Table A-17. Show Commands 2Displays either console enabled or console disabled Show bridge Show dhcp server Table A-17. Show Commands 3Show dhcp relay Show ip route ip-address Table A-17. Show Commands 4Show interface eth1 dsl1 Show nat napt Table A-17. Show Commands 5Show nat basic Show spanning-tree Table A-17. Show Commands 6Show pppoe Show statistics eth1 Table A-17. Show Commands 7Show statistics eth1 dsl1 ip bridge pppoe tftp Show statistics dsl1 Table A-17. Show Commands 8Show statistics ip Show statistics bridge Show statistics tftp Table A-17. Show Commands 9Show statistics pppoe Show system Table A-17. Show Commands 10Show telnet Show traps Command Line Interface November Configuration Default Settings Configuration Defaults Command Line Shortcuts A-17 Table B-2. Command Line Shortcuts 1 Command Line ShortcutsArp create ip-addr mac-addr Arp delete ip-addr Table B-2. Command Line Shortcuts 2 Table B-2. Command Line Shortcuts 3 Show nat basic napt Show pppoe Table B-2. Command Line Shortcuts 4Show syslog Show system Show telnet Syslog ip ip-addrmgt srvc Traps Overview Traps and MIBsSnmp Overview Variable Binding DSL Router Traps MIB II RFC MIBs OverviewStandard MIBs System System Group IfEntry Interfaces Group RFCInterfaces IfType Identifies the interface type based Supported values IfXEntry Extension to Interfaces Table RFCMbps True1 IP Group RFC Table C-5. IP Group Objects Description Setting/Contents IpCidrRouteEntry IP Cidr Route Group RFCIpForward Snmp Group Transmission Group Ethernet-Like MIB RFC Paradyne Enterprise MIBs NoOp1 Device Control MIBActive1 Inactive2 Ping Test Device Diagnostics MIBTraceRoute InProgress2 Active test IcmpError TimeoutSystemError ApplpingTestEntry Traceroute ConfigureApplTracerouteResultsEntry AppTracerouteResultsEntry DevStatus Health and Status MIBDevStatus1 Factory1-to-active8 Configuration MIB PdnInetIpAddressTableEntry Interface Configuration MIBPrimary Secondary Dhcp MIB DSL Endpoint MIB DSL Router Terminal Emulation Accessing the List Command Output Terminal Emulation Programs Firmware Upgrade Commands Firmware UpgradeOverview Apply download Download dsl1ifn eth1ifn server-ip filename Firmware Upgrade ProceduresDownload ifn address eth1 155.1.3.254 Paradyne server Downloading will affect user data performance Are you sure? No new firmware to apply At the CUSTOMER-CONFIG# prompt, type apply downloadSystem is being reset Firmware Upgrade November Index Symbols IN-2 IN-3 IN-4 IN-5 IN-6