
C. Traps and MIBs
Table
Object | Description | Setting/Contents |
|
|
|
applTracerouteTestId | Unique TraceRoute test ID. | Contains applNewTestID after Get. |
(traceroute 1) |
|
|
|
|
|
applTracerouteIpAddress | Destination IP address for | Set destination IP address. |
(traceroute 2) | TraceRoute test. |
|
|
|
|
applTracerouteSourceIpAddress | Identifies the source IP address. | Set source IP address. |
(traceroute 3) |
|
|
|
|
|
applTraceroutePacketSize | Specifies TraceRoute packet size. | 28 — 15028 – Range. |
(traceroute 4) | Range + 28 bytes of header | 64 – Default. |
| information. | |
|
| |
|
|
|
applTracerouteTimeOut | Timeout value in seconds | 10 – Default. |
(traceroute 5) | between echo request attempts. |
|
|
|
|
applTracerouteMaxHops | Maximum number of hops to be | 8 – Default. |
(traceroute 6) | tested. |
|
|
|
|
applTracerouteDomain | Specifies the destination IP | mgmt(2) – Management Domain. |
(traceroute 7) | address’s service domain. | service(3) – Service Domain. Default. |
|
| |
|
|
|
applTracerouteIfIndex | Specifies the route for the | If the target interface is not specified, the |
(traceroute 8) | TraceRoute test. | default will display the calculated ifIndex. |
|
|
|
applTracerouteTestOwner | Identifies who started the test. | 1 – 40 characters. |
(traceroute 9) |
|
|
|
|
|
applTracerouteTestId | Contains the results of a | Supports only one test per device. |
(applTracerouteResultsEntry 1) | TraceRoute test. |
|
|
|
|
applTracerouteHopCount | Number of hops to reach the | — |
(applTracerouteResultsEntry 2) | gateway. |
|
|
|
|
applTracerouteResultsIpAddr | IP address of the gateway. | — |
(applTracerouteResultsEntry 3) |
|
|
|
|
|
applTracerouteResultsHopCount | Number of hops to reach the | — |
(applTracerouteResultsEntry 4) | gateway. |
|
|
|
|
applTracerouteResultsPacketSize | Specifies the data size of the | — |
(applTracerouteResultsEntry 5) | packets (in bytes) sent during the |
|
| TraceRoute test. |
|
|
|
|
applTracerouteResultsProbe1 | Displays roundtrip time in 100 ms | 0 – Probe has timed out. |
(appTracerouteResultsEntry 6) | intervals of the first probe sent to |
|
| the gateway. |
|
|
|
|
applTracerouteResultsProbe2 | Displays roundtrip time in 100 ms | 0 – Probe has timed out. |
(applTracerouteResultsEntry 7) | intervals of the second probe sent |
|
| to the gateway. |
|
|
|
|
applTracerouteResultsProbe3 | Displays roundtrip time in 100 ms | 0 – Probe has timed out. |
(applTracerouteResultsEntry 8) | intervals of the third probe sent to |
|
| the gateway. |
|
|
|
|
diagTestTrapEnable | Use to enable or disable | Bit Sum. |
(configure 1) | diagApplTestStopdiagApplTestStart traps.and | 1 – Test Start. |
|
| 2 – Test Over. |
|
|
|
November 2003 |