SmartLink M-ATA | Patton electronic instruction

SmartLink M-ATA

Micro-Analog Telephone Adapter

Getting Started Guide

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail:support@patton.com

WWW: www.patton.com

Document Number: 09405U1-001 Rev. B

Part Number: 07MSLMATA-GS

Revised: October 4, 2006

Image 1

Patton electronic manual SmartLink M-ATA

Contents

SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables Audience About this guideStructure Safety when working with electricity Precautions General observations Typographical conventions used in this documentGeneral conventions General information Chapter contents SmartLink M-ATA SmartLink M-ATA overview SmartLink installation Phone Power adapter Installing the M-ATA Resetting the M-ATA to factory default System information System Uptime Home System information System Status Network-LAN Status Network SettingsInterface Status Settings Obtain LAN conﬁguration dynamically Internet ConﬁgurationSpecify ﬁxed LAN conﬁguration Authentication Enable PPPoESettings WAN PPPoE Conﬁguration MAC Spooﬁng Conﬁguration Conﬁguring Dynamic DNSWAN MAC Address Spoofed Vlan Conﬁguration Vlan Tag Ieee 802.1q ToS/DiffServPriority Tag Ieee 802.1q Saving your work Telephony Telephony Telephony VoIP Server Registration Status VoIP StatusPhone Line Status User Name Caller ID SettingSubscribed for Voicemail Messages waiting Gateway Settings SIP Server SettingsSIP Conﬁguration RTP Telephone Event Conﬁguration SIP ExtensionsVoIP Vlan Conﬁguration SIP Parameters SIP Timer Values millisecondsHook Flash Mime Type RTP Parameters NAT Traversal Packetization Audio/CODEC ConﬁgurationJitter Buffer FAX without T.38 Use G.711 fax User Information Phone Supplementary Service Activation Distinctive Ring Message Waiting IndicatorCall Transfer Dialing by IP Address Dial Out Type Call Forward Settings Incoming Call Block Selective Call Forward SettingsOutgoing Call Block Line 1 Speed Dial Settings Http Digest SettingSpeed Dial Speed Dial Serv System System System New Root Password Set Security PasswordNew User Password Conﬁrm new password Enable Syslog Syslog ServiceConﬁguration Syslog Server Enable Debug Debug ServiceNTP Service Debug Server Time Zone Adjust clock for daylight savings Service AccessEnable Http Enable Ping Reply Call Progress Tones Localization Prompt Tone Dial ToneConﬁrm Tone Holding Tone Following is a sample ring cadence pattern conﬁguration Distinctive Ring Settings Call forward selective Supplementary Service KeysBlock Anonymous Calls Warm Line Speed Dialing IP DialingIncome Caller ID Calling Preﬁx Keys Call Waiting call alternative Call HoldCall Conference Call Conference Drop Control Timer Values FXS Port FXS Port Polarity Conﬁguration Ring Setting Snmp Trap Conﬁguration Snmp ConﬁgurationSnmp Community Conﬁguration Snmp System Conﬁguration Auto Upgrade Manual Upgrade window Manual Upgrade Reload Documentation Documentation link Introduction Logout Logout window Contacting Patton for assistance Patton support headquarters in the USA Contact information RMA numbers Warranty coverage Appendix a Compliance information Compliance Safety ComplianceRadio and TV Interference FCC Part CE Notice Declarations of Conformity Appendix B Speciﬁcations Voice Connectivity Voice Processing signalling dependentConnectivity Fax and Modem Support IP Services Voice Services/FeaturesManagement Operating Environment Appendix C Dial plans Simple Dial Plan Sample Dial PlansNon-dialed Line Dial Plan Complex Dial Plan Sample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt conﬁguration Existing voice prompt conﬁguration Accessing the voice prompt