ToS/DiffServ, Vlan Tag Ieee 802.1q | Patton electronic M-ATA

SmartLink M-ATA Getting Started Guide	4 • Network—LAN

cessed. All data leaving the SmartLink M-ATA will be marked with the speciﬁc value unless overridden on the telephony VLAN conﬁguration settings.

Figure 9. VLAN Conﬁguration section of the Settings window

VLAN Tag (IEEE 802.1q)

IEEE 802.1q Ethernet VLAN tag for all outgoing packets on LAN Ethernet interface. The value should be between 0 and 4094.

Priority Tag (IEEE 802.1q)

IEEE 802.1q Ethernet Priority tag for all outgoing packets on LAN Ethernet interface. The value should be between 0 and 7.

Saving your work

When you are ﬁnished conﬁguring the VLAN settings, click the Save and Reload button (see ﬁgure 9) to save all changes.

ToS/DiffServ

This sub-page is used to conﬁgure the Type-of-Service/Diffserv byte values which are to be used in the IP header of all transmitted SIP signaling packets and RTP packets. The ToS/DiffServ byte values are entered as two-digit hexadecimal values. If no special ToS/DiffServ value is to be used for a particular trafﬁc type, enter 00 or leave the setting empty.

Figure 10. TOS/DiffServ window

Saving your work

When you are ﬁnished conﬁguring ToS/DiffServ settings, click the Save ToS/DiffServ Settings button to save the changes.

ToS/DiffServ

31

Image 31

Patton electronic M-ATA manual ToS/DiffServ, Vlan Tag Ieee 802.1q, Priority Tag Ieee 802.1q, Saving your work

Contents

SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables Audience About this guideStructure Safety when working with electricity Precautions General observations Typographical conventions used in this documentGeneral conventions General information Chapter contents SmartLink M-ATA SmartLink M-ATA overview SmartLink installation Phone Power adapter Installing the M-ATA Resetting the M-ATA to factory default System information System Uptime Home System information System Status Network-LAN Status Network SettingsInterface Status Settings Obtain LAN conﬁguration dynamically Internet ConﬁgurationSpecify ﬁxed LAN conﬁguration WAN PPPoE Conﬁguration Enable PPPoEAuthentication Settings Vlan Conﬁguration Conﬁguring Dynamic DNSMAC Spooﬁng Conﬁguration WAN MAC Address Spoofed Saving your work ToS/DiffServVlan Tag Ieee 802.1q Priority Tag Ieee 802.1q Telephony Telephony Telephony VoIP Server Registration Status VoIP StatusPhone Line Status Messages waiting Caller ID SettingUser Name Subscribed for Voicemail Gateway Settings SIP Server SettingsSIP Conﬁguration RTP Telephone Event Conﬁguration SIP ExtensionsVoIP Vlan Conﬁguration RTP Parameters SIP Timer Values millisecondsSIP Parameters Hook Flash Mime Type NAT Traversal FAX without T.38 Use G.711 fax Audio/CODEC ConﬁgurationPacketization Jitter Buffer User Information Phone Supplementary Service Activation Dialing by IP Address Message Waiting IndicatorDistinctive Ring Call Transfer Dial Out Type Call Forward Settings Incoming Call Block Selective Call Forward SettingsOutgoing Call Block Speed Dial Serv Http Digest SettingLine 1 Speed Dial Settings Speed Dial System System System Conﬁrm new password Set Security PasswordNew Root Password New User Password Syslog Server Syslog ServiceEnable Syslog Conﬁguration Debug Server Debug ServiceEnable Debug NTP Service Enable Ping Reply Service AccessTime Zone Adjust clock for daylight savings Enable Http Call Progress Tones Localization Holding Tone Dial TonePrompt Tone Conﬁrm Tone Following is a sample ring cadence pattern conﬁguration Distinctive Ring Settings Warm Line Supplementary Service KeysCall forward selective Block Anonymous Calls Calling Preﬁx Keys IP DialingSpeed Dialing Income Caller ID Call Conference Drop Call HoldCall Waiting call alternative Call Conference Control Timer Values FXS Port FXS Port Polarity Conﬁguration Ring Setting Snmp System Conﬁguration Snmp ConﬁgurationSnmp Trap Conﬁguration Snmp Community Conﬁguration Auto Upgrade Manual Upgrade window Manual Upgrade Reload Documentation Documentation link Introduction Logout Logout window Contacting Patton for assistance Patton support headquarters in the USA Contact information RMA numbers Warranty coverage Appendix a Compliance information CE Notice Declarations of Conformity Safety ComplianceCompliance Radio and TV Interference FCC Part Appendix B Speciﬁcations Fax and Modem Support Voice Processing signalling dependentVoice Connectivity Connectivity Operating Environment Voice Services/FeaturesIP Services Management Appendix C Dial plans Complex Dial Plan Sample Dial PlansSimple Dial Plan Non-dialed Line Dial Plan Sample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt conﬁguration Existing voice prompt conﬁguration Accessing the voice prompt