Ring Setting | Patton electronic M-ATA specs

SmartLink M-ATA Getting Started Guide	6 • System

Ring Setting

Figure 38. Ring Setting section of Localization window

Ring Waveform

Specify the ring tone waveform.

Ring Frequency

Specify the ring tone frequency.

Ring Voltage

Specify the ring tone voltage.

FXS Port Polarity Conﬁguration

Figure 39. FXS Port Polarity section of Localization window

Idle Polarity

Polarity before call connected.

Caller Conn Polarity

Polarity after outbound call connected.

Saving your work

When you are ﬁnished conﬁguring settings, click the Save button (see ﬁgure 39) to save the changes.

Localization

63

Image 63

Patton electronic M-ATA manual Ring Setting, FXS Port Polarity Conﬁguration

Contents

SmartLink M-ATA Mailsupport@patton.com Summary Table of Contents Table of Contents Telephony None Table of Contents System Table of Contents Documentation Calling Features List of Figures List of Tables About this guide AudienceStructure Safety when working with electricity Precautions Typographical conventions used in this document General observationsGeneral conventions General information Chapter contents SmartLink M-ATA SmartLink M-ATA overview SmartLink installation Phone Power adapter Installing the M-ATA Resetting the M-ATA to factory default System information System Uptime Home System information System Status Network-LAN Network Settings StatusInterface Status Settings Internet Conﬁguration Obtain LAN conﬁguration dynamicallySpecify ﬁxed LAN conﬁguration WAN PPPoE Conﬁguration Enable PPPoEAuthentication Settings Vlan Conﬁguration Conﬁguring Dynamic DNSMAC Spooﬁng Conﬁguration WAN MAC Address Spoofed Saving your work ToS/DiffServVlan Tag Ieee 802.1q Priority Tag Ieee 802.1q Telephony Telephony Telephony VoIP Status VoIP Server Registration StatusPhone Line Status Messages waiting Caller ID SettingUser Name Subscribed for Voicemail SIP Server Settings Gateway SettingsSIP Conﬁguration SIP Extensions RTP Telephone Event ConﬁgurationVoIP Vlan Conﬁguration RTP Parameters SIP Timer Values millisecondsSIP Parameters Hook Flash Mime Type NAT Traversal FAX without T.38 Use G.711 fax Audio/CODEC ConﬁgurationPacketization Jitter Buffer User Information Phone Supplementary Service Activation Dialing by IP Address Message Waiting IndicatorDistinctive Ring Call Transfer Dial Out Type Call Forward Settings Selective Call Forward Settings Incoming Call BlockOutgoing Call Block Speed Dial Serv Http Digest SettingLine 1 Speed Dial Settings Speed Dial System System System Conﬁrm new password Set Security PasswordNew Root Password New User Password Syslog Server Syslog ServiceEnable Syslog Conﬁguration Debug Server Debug ServiceEnable Debug NTP Service Enable Ping Reply Service AccessTime Zone Adjust clock for daylight savings Enable Http Call Progress Tones Localization Holding Tone Dial TonePrompt Tone Conﬁrm Tone Following is a sample ring cadence pattern conﬁguration Distinctive Ring Settings Warm Line Supplementary Service KeysCall forward selective Block Anonymous Calls Calling Preﬁx Keys IP DialingSpeed Dialing Income Caller ID Call Conference Drop Call HoldCall Waiting call alternative Call Conference Control Timer Values FXS Port FXS Port Polarity Conﬁguration Ring Setting Snmp System Conﬁguration Snmp ConﬁgurationSnmp Trap Conﬁguration Snmp Community Conﬁguration Auto Upgrade Manual Upgrade window Manual Upgrade Reload Documentation Documentation link Introduction Logout Logout window Contacting Patton for assistance Patton support headquarters in the USA Contact information RMA numbers Warranty coverage Appendix a Compliance information CE Notice Declarations of Conformity Safety ComplianceCompliance Radio and TV Interference FCC Part Appendix B Speciﬁcations Fax and Modem Support Voice Processing signalling dependentVoice Connectivity Connectivity Operating Environment Voice Services/FeaturesIP Services Management Appendix C Dial plans Complex Dial Plan Sample Dial PlansSimple Dial Plan Non-dialed Line Dial Plan Sample Dial Plans Appendix D Calling Features Distinctive on Distinctive OFF Appendix E Voice prompt conﬁguration Existing voice prompt conﬁguration Accessing the voice prompt