Philips DVP3345V/17 Timer Recording cont’d, Press Clear to remove the menu Press Timer SET

E8E20UD_EN1 8/23/07 1:25 PM Page 25

Timer Recording (cont’d) 25

7 Press K or L to select a recording tape speed. The arrow will appear beside your choice. The selected speed will flash beside REC SPEED. Details about tape speed are on page 57.

You must select the recording speed to complete the timer programming.

ONE TIME PROGRAM

PROGRAM NUMBER 1

DATE	0 8 / 2 9	WED
START TIME	0 7 : 3 0	P M

OPEN/CLOSE

1 2 3

4 5 6

TRACKING

7 8 9

CLEAR TITLE

English

END TIME	0 8 : 3 0 P M
L1/L2	L2
REC SPEED	S P

BSP SLP

8 Press CLEAR to remove the menu.

Press TIMER SET.

+10 0

VCR SETUP

INPUT

OK

DVD

DISC MENU

8

7

9 ● Ininstead.some cases, the DVD/VCR will switch to DVD mode You may use the DVD player during a Timer Recording.

● If you want to use the VCR until time for the recording,

don’t press TIMER SET until a few minutes before the recording should start. Or, press TIMER SET only when you know you won’t be using the VCR anymore (until after the recording).

● When “” is lit (not flashing), you cannot put the DVD/VCR in VCR mode by pressing VCR or SOURCE. You must first press TIMER SET on the remote control or STOP/EJECT C A on the front panel to cancel the Timer Recording temporarily. Then, you can use the VCR features again.

When a Timer Recording ends

The DVD/VCR will turn off and “” on the DVD/VCR’s display panel will flash indicating that the recording is complete, then goes into the timer standby mode again. (It may switch to DVD mode automatically.) At this point, you cannot use the VCR unless you release the DVD/VCR from the timer standby mode.

To release the DVD/VCR from timer standby mode

●If the DVD component is active and no more Timer Recordings are on standby, you can cancel the timer standby mode by pressing TIMER SET or VCR on the remote control or by pressing SOURCE or STOP/EJECT C A on the front panel.

●If the DVD component is not active, or the “” is not flashing but lit indicating there are more Timer Recordings on standby, you can cancel the timer standby mode only by pressing TIMER SET on the remote control or by pressing STOP/EJECT C A on the front panel.

●After releasing the DVD/VCR from timer standby mode, you can use it as usual.

Canceling a Timer Recording Before the Recording Starts

1 Press VCR, then press SETUP so MENU appears.

2 Press K or L to select TIMER PROGRAMMING, then press B.

3 Press K or L to find the program you want to cancel.

4 While the program number is flashing, press s to clear all the information for that program.

5 Press CLEAR to remove the menu.

REW PLAY FFW

STOP PAUSE BACK

DISPLAY SUBTITLE ZOOM AUDIO

ANGLE	SEARCH	REPEAT	REPEAT
			A-B	9
REC	SPEED	MODE	TIMER SET

Helpful Hints

•To stop a started Timer Recording, press STOP/EJECT CA on the front of the DVD/VCR. (You cannot stop a started Timer Recording with STOP C on the remote.)

•To change incorrect information, press s or B to choose the item you want to change. Press K or Lto adjust the information.

•If there is no tape in the VCR when you press TIMER SET,

“ ” will flash. Insert a tape.

•If one or more Timer Recordings are on standby when one Timer Recording ends, the DVD/VCR will turn off automatically and

“ ” will appear on the

DVD/VCR’s display panel indicating that it is now ready for another Timer Recording.