Turn Extending Table Character On/Off | Printronix PSA3 specs

Chapter 3 Configuring The KSSM Emulation With Control Codes

Turn Extending Table Character On/Off

ASCII Code	FS v n
Hex Code	1C 76 n
Dec Code	28 118 n
Purpose	Turns on/off extending table characters, as follows:
	n = 0 or 48Cancels extending table characters
	n = 1 or 49Selects extending table characters
	Where:
	n = 0, 1, 48, 49
Comment	This command extends the table characters so they touch in
	both horizontal and vertical directions.
	The limitation of extension is ½ inch.
	Our printer could extend the table characters in the range of
	A6A1H to A6E4H in the Hangul Complete font.
	The default is Table Character not extended.

Turn On/Off OCRB Selection

ASCII Code ASSC 0 z n

Hex Code ASSC 30 7A n

Dec Code ASSC 48 122 n

Purpose Turns on/off OCRB selection as follows: n = 0 or 48Turns off OCRB selection

n = 1 or 49Turns on OCRB selection

Where:

n = 0, 1, 48, 49

Comment When OCRB selection is turned on, the OCRB character can be printed out.

This command affects the front panel setting of “OCRB

Selection.”

This command works only in DBCS mode.

The default is n = 0.

78

Image 78

Printronix PSA3, P7000 H-Series Turn Extending Table Character On/Off, Turn On/Off Ocrb Selection, Ascii Code Assc 0 z n

Contents

Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table Software Features About This ManualRelated Product Information Software Features Introduction Control Panel Printing The Configuration Printing The Configuration Printing Configurations Step Key Result Allows you to make configuration changes Locks the Enter key Configuration Menu Configuration Menu Overview Moving Within The Configuration Menu Configuration MenuChanging Configurations Step Key Result To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus Menu CPI/LPI Select Font Attributes Margins Form LengthForm Width Perforation Skip Kssm Emulation Kssm Emulation Define CR Code Kssm Emulation Exceptions And Differences Default Values And States Factory Settings Characteristic Default Setting Escape Sequences FS Sequences Set And Reset Codes Configuring The Kssm Emulation With Control CodesSuper-Set Commands Format For Control Code Descriptions Control Code Index Setting the Page FormatSetting the Units Control Code Index Selecting Characters Control-code Character PrintingMechanical Control Hangul Extension Commands Printing GraphicsData and Memory Control Advance Print Position Vertically Align Sbcs Character with Dbcs Character Backspace Cancel The Alignment of Sbcs Character With Dbcs CharacterCancel The Alignment of Sbcs Character With Ascii Code Hex Code Dec Code Purpose Barcode Printing Ascii Hex Selects Barcode Barcode Printing Ascii Selects Value Offset unitInch UPC-A UPC-E EAN Carriage Return Cancel LineBeeper Beeper Define Pattern for Special Printing Effect Define User-Defined Character Define User-Defined Chinese Character Define User-Defined Chinese CharacterDelete Last Character in Buffer Hex Code Dec Code Enable Printing of Upper Control Codes Divided Hangul Double Height Enable Upper Control Codes Enable Upper Control CodesFont Expansion Form Feed Graphic Printing Graphics Printing Select Bit Image Initialize PrinterGraphics Printing Select Bit Image Line Feed Ascii Code ESC ! n Hex Code Master SelectMaster Select Bit On/Off Hex Dec Function Equivalent Master Select In Dbcs Mode Ascii Code FS ! n Hex Code Pair Two Characters in Vertical Printing Master Select One-Line Attribute In Dbcs ModeMaster Select One-Line Attribute In Dbcs Mode Bit On/Off Hex Dec Function Reassign Bit-image Mode Select 1/6-inch Line SpacingSelect 1/8-inch Line Spacing Select 15 CPI Select 10 CPISelect 12 CPI Select 10 CPI Select 60-dpi Graphics Select 120-dpi Graphics Select 240-dpi Graphics Select 120-dpi Graphics Select an International Character Set USA Select Bit Image Select Bit Image Cancel Bold Font Select Bold FontSelect Character Style Select Character Table Select Character TableSelect Condensed Printing Ascii Code ESC t n Hex Code Cancel Condensed Printing Select Double-strike Printing Cancel Double-strike PrintingSelect Dbcs Print Quality Select Dbcs Print Quality Cancel Double-width Printing One Line Select Double-width Printing One Line Select Double-width Printing in Dbcs Mode One Line Cancel Double-width Printing in Dbcs Mode One LineSelect Double-width Printing in Dbcs Mode One Select Hangul Myunjo/Gothic Style Select Dbcs ModeCancel Dbcs Mode Ascii Code Hex Code Select Print Quality Cancel Italic FontSelect Italic Font Select Italic Font Select Printer Deselect PrinterSelect Superscript/Subscript Printing Select Dbcs Super/Subscript Printing Cancel Superscript/Subscript PrintingCancel Superscript/Subscript Printing Select Vertical Printing Cancel Vertical Printing Select Horizontal Printing Set n/60-inch Line SpacingSet n/180-inch Line Spacing Set Bottom Margin Cancel Bottom MarginSet Absolute Horizontal Print Position Set Absolute Horizontal Print Position Set Horizontal Tabs Cancel Dbcs Character Half Width Super/Subscript PrintingSet Dbcs Character Half Width Ascii Code ESC D n1 n2 … nk NUL Set Intercharacter Space Set Intercharacter Space Set Left Margin Set Page Length In Inches Set Page Length In LinesSet Page Length In Inches Set Relative Horizontal Print Position Set Right Margin Set Vertical Tab Channels Set Vertical Tab ChannelsSet Vertical Tabs Ascii Code ESC B n1 n2 … nk NUL Set Vertical Tabs In VFU Channels Ascii Code ESC b m n1 … nk NULDec Code 27 98 m n1 … nk Tab Horizontally Tab VerticallyTab Horizontally Turn Auto-wrap Around On/Off Turn Double-Height Printing On/Off Turn Double-Width, Double-Height Printing On/Off Turn Double-Width Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn Extending Table Character On/Off Turn On/Off Ocrb SelectionAscii Code Assc 0 z n Turn Proportional Mode On/Off Turn Proportional Mode On/OffTurn Underline On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Customer Support Center Printronix Supplies Department Corporate Offices Appendix C Contact Information Index Page Page 100 Page 179981-001