Printronix Customer Support Center | Printronix P7000 H-Series

C Contact Information

Printronix Customer Support Center

IMPORTANT Please have the following information available prior to calling the Printronix Customer Support Center:

•Model number

•Serial number (located on the back of the printer)

•Installed options (i.e., interface and host type if applicable to the problem)

•Configuration printout:

Line Matrix Printer

Press PRT CONFIG on the control panel, then press Enter.

•Is the problem with a new install or an existing printer?

•Description of the problem (be specific)

•Good and bad samples that clearly show the problem (faxing of these samples may be required)

Americas	(714) 368-2686
Europe, Middle East, and Africa	(31)	24 6489 311
Asia Pacific	(65)	6548 4114

http://www.printronix.com/support.aspx

Printronix Supplies Department

Contact the Printronix Supplies Department for genuine Printronix supplies.

Americas	(800) 733-1900
Europe, Middle East, and Africa	(33)	1 46 25 1900
Asia Pacific	(65)	6548 4116
	or (65) 6548 4182

http://www.printronix.com/supplies-parts.aspx

95

Image 95

Printronix P7000 H-Series, PSA3 manual Printronix Customer Support Center, Printronix Supplies Department

Contents

Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table Related Product Information Software FeaturesAbout This Manual Software Features Control Panel Introduction Printing The Configuration Printing The Configuration Allows you to make configuration changes Printing Configurations Step Key Result Locks the Enter key Configuration Menu Overview Configuration Menu Changing Configurations Step Key Result Moving Within The Configuration MenuConfiguration Menu To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus Menu CPI/LPI Select Font Attributes Perforation Skip Form LengthForm Width Margins Kssm Emulation Kssm Emulation Define CR Code Exceptions And Differences Kssm Emulation Factory Settings Characteristic Default Setting Default Values And States FS Sequences Escape Sequences Format For Control Code Descriptions Configuring The Kssm Emulation With Control CodesSuper-Set Commands Set And Reset Codes Control Code Index Setting the Page FormatSetting the Units Control Code Index Mechanical Control Selecting CharactersControl-code Character Printing Data and Memory Control Hangul Extension CommandsPrinting Graphics Align Sbcs Character with Dbcs Character Advance Print Position Vertically Ascii Code Hex Code Dec Code Purpose Cancel The Alignment of Sbcs Character With Dbcs CharacterCancel The Alignment of Sbcs Character With Backspace Ascii Hex Selects Barcode Barcode Printing Inch Barcode Printing Ascii Selects ValueOffset unit UPC-A UPC-E EAN Beeper Cancel LineBeeper Carriage Return Define User-Defined Character Define Pattern for Special Printing Effect Hex Code Dec Code Define User-Defined Chinese CharacterDelete Last Character in Buffer Define User-Defined Chinese Character Divided Hangul Double Height Enable Printing of Upper Control Codes Font Expansion Enable Upper Control CodesEnable Upper Control Codes Graphic Printing Form Feed Graphics Printing Select Bit Image Graphics Printing Select Bit ImageInitialize Printer Line Feed Bit On/Off Hex Dec Function Equivalent Master SelectMaster Select Ascii Code ESC ! n Hex Code Ascii Code FS ! n Hex Code Master Select In Dbcs Mode Bit On/Off Hex Dec Function Master Select One-Line Attribute In Dbcs ModeMaster Select One-Line Attribute In Dbcs Mode Pair Two Characters in Vertical Printing Select 1/8-inch Line Spacing Reassign Bit-image ModeSelect 1/6-inch Line Spacing Select 10 CPI Select 10 CPISelect 12 CPI Select 15 CPI Select 120-dpi Graphics Select 60-dpi Graphics Select 120-dpi Graphics Select 240-dpi Graphics USA Select an International Character Set Select Bit Image Select Bit Image Select Character Style Cancel Bold FontSelect Bold Font Ascii Code ESC t n Hex Code Select Character TableSelect Condensed Printing Select Character Table Cancel Condensed Printing Select Dbcs Print Quality Cancel Double-strike PrintingSelect Dbcs Print Quality Select Double-strike Printing Select Double-width Printing One Line Cancel Double-width Printing One Line Select Double-width Printing in Dbcs Mode One Select Double-width Printing in Dbcs Mode One LineCancel Double-width Printing in Dbcs Mode One Line Ascii Code Hex Code Select Dbcs ModeCancel Dbcs Mode Select Hangul Myunjo/Gothic Style Select Italic Font Cancel Italic FontSelect Italic Font Select Print Quality Select Superscript/Subscript Printing Select PrinterDeselect Printer Select Vertical Printing Cancel Superscript/Subscript PrintingCancel Superscript/Subscript Printing Select Dbcs Super/Subscript Printing Set n/180-inch Line Spacing Cancel Vertical Printing Select Horizontal PrintingSet n/60-inch Line Spacing Set Absolute Horizontal Print Position Cancel Bottom MarginSet Absolute Horizontal Print Position Set Bottom Margin Ascii Code ESC D n1 n2 … nk NUL Cancel Dbcs Character Half Width Super/Subscript PrintingSet Dbcs Character Half Width Set Horizontal Tabs Set Intercharacter Space Set Intercharacter Space Set Left Margin Set Page Length In Inches Set Page Length In InchesSet Page Length In Lines Set Right Margin Set Relative Horizontal Print Position Ascii Code ESC B n1 n2 … nk NUL Set Vertical Tab ChannelsSet Vertical Tabs Set Vertical Tab Channels Dec Code 27 98 m n1 … nk Set Vertical Tabs In VFU ChannelsAscii Code ESC b m n1 … nk NUL Tab Horizontally Tab HorizontallyTab Vertically Turn Double-Height Printing On/Off Turn Auto-wrap Around On/Off Turn Double-Width, Double-Height Printing On/Off Turn Double-Width, Double-Height Printing On/OffTurn Double-Width Printing On/Off Ascii Code Assc 0 z n Turn Extending Table Character On/OffTurn On/Off Ocrb Selection Turn Underline On/Off Turn Proportional Mode On/OffTurn Proportional Mode On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Korean Standard Code Table KSC5601 Code Table Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Supplies Department Printronix Customer Support Center Appendix C Contact Information Corporate Offices Index Page Page 100 Page 179981-001