Select Bit Image | Printronix P7000 H-Series, PSA3 manual

Select Bit Image

Select Bit Image

ASCII Code ESC * m nL nH d1 … dk

Hex Code 1B 2A m nL nH d1 … dk

Dec Code 27 42 m nL nH d1 … dk

Purpose Prints dot-graphics in 8- or 24-dot columns, depending on the following parameters:

mSpecifies the dot density

nL, nH	Specifies the total number of columns of graphics
	data that follows (number of dot columns) = ((nHx
	256) + nL)
d1 … dk	Bytes of graphics data; k is determined by multiplying
	the total number of columns times the number of
	bytes required for each column

Dot density is described in the table below:

Parameter	Horizontal	Vertical	Dots per	Bytes per
m in ESC *	density (dpi)	density (dpi)	column	column

0	60	60	8	1

1	120	60	8	1

2	120	60	8	1

3	240	60	8	1

4	80	60	8	1

6	90	60	8	1

32	60	180	24	3

33	120	180	24	3

38	90	180	24	3

39	180	180	24	3

40	360	180	24	3

	Where:

0 <= nL <= 255

0 <= nH <= 31

m = 0, 1, 2, 3, 4, 6, 32, 33, 38, 39 40

55

Image 55

Printronix P7000 H-Series, PSA3 manual Select Bit Image

Contents

Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table About This Manual Software FeaturesRelated Product Information Software Features Control Panel Introduction Printing The Configuration Printing The Configuration Allows you to make configuration changes Printing Configurations Step Key Result Locks the Enter key Configuration Menu Overview Configuration Menu Configuration Menu Moving Within The Configuration MenuChanging Configurations Step Key Result To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus Menu CPI/LPI Select Font Attributes Perforation Skip Form LengthForm Width Margins Kssm Emulation Kssm Emulation Define CR Code Exceptions And Differences Kssm Emulation Factory Settings Characteristic Default Setting Default Values And States FS Sequences Escape Sequences Format For Control Code Descriptions Configuring The Kssm Emulation With Control CodesSuper-Set Commands Set And Reset Codes Control Code Index Setting the Page FormatSetting the Units Control Code Index Control-code Character Printing Selecting CharactersMechanical Control Printing Graphics Hangul Extension CommandsData and Memory Control Align Sbcs Character with Dbcs Character Advance Print Position Vertically Ascii Code Hex Code Dec Code Purpose Cancel The Alignment of Sbcs Character With Dbcs CharacterCancel The Alignment of Sbcs Character With Backspace Ascii Hex Selects Barcode Barcode Printing Offset unit Barcode Printing Ascii Selects ValueInch UPC-A UPC-E EAN Beeper Cancel LineBeeper Carriage Return Define User-Defined Character Define Pattern for Special Printing Effect Hex Code Dec Code Define User-Defined Chinese CharacterDelete Last Character in Buffer Define User-Defined Chinese Character Divided Hangul Double Height Enable Printing of Upper Control Codes Enable Upper Control Codes Enable Upper Control CodesFont Expansion Graphic Printing Form Feed Initialize Printer Graphics Printing Select Bit ImageGraphics Printing Select Bit Image Line Feed Bit On/Off Hex Dec Function Equivalent Master SelectMaster Select Ascii Code ESC ! n Hex Code Ascii Code FS ! n Hex Code Master Select In Dbcs Mode Bit On/Off Hex Dec Function Master Select One-Line Attribute In Dbcs ModeMaster Select One-Line Attribute In Dbcs Mode Pair Two Characters in Vertical Printing Select 1/6-inch Line Spacing Reassign Bit-image ModeSelect 1/8-inch Line Spacing Select 10 CPI Select 10 CPISelect 12 CPI Select 15 CPI Select 120-dpi Graphics Select 60-dpi Graphics Select 120-dpi Graphics Select 240-dpi Graphics USA Select an International Character Set Select Bit Image Select Bit Image Select Bold Font Cancel Bold FontSelect Character Style Ascii Code ESC t n Hex Code Select Character TableSelect Condensed Printing Select Character Table Cancel Condensed Printing Select Dbcs Print Quality Cancel Double-strike PrintingSelect Dbcs Print Quality Select Double-strike Printing Select Double-width Printing One Line Cancel Double-width Printing One Line Cancel Double-width Printing in Dbcs Mode One Line Select Double-width Printing in Dbcs Mode One LineSelect Double-width Printing in Dbcs Mode One Ascii Code Hex Code Select Dbcs ModeCancel Dbcs Mode Select Hangul Myunjo/Gothic Style Select Italic Font Cancel Italic FontSelect Italic Font Select Print Quality Deselect Printer Select PrinterSelect Superscript/Subscript Printing Select Vertical Printing Cancel Superscript/Subscript PrintingCancel Superscript/Subscript Printing Select Dbcs Super/Subscript Printing Set n/60-inch Line Spacing Cancel Vertical Printing Select Horizontal PrintingSet n/180-inch Line Spacing Set Absolute Horizontal Print Position Cancel Bottom MarginSet Absolute Horizontal Print Position Set Bottom Margin Ascii Code ESC D n1 n2 … nk NUL Cancel Dbcs Character Half Width Super/Subscript PrintingSet Dbcs Character Half Width Set Horizontal Tabs Set Intercharacter Space Set Intercharacter Space Set Left Margin Set Page Length In Lines Set Page Length In InchesSet Page Length In Inches Set Right Margin Set Relative Horizontal Print Position Ascii Code ESC B n1 n2 … nk NUL Set Vertical Tab ChannelsSet Vertical Tabs Set Vertical Tab Channels Ascii Code ESC b m n1 … nk NUL Set Vertical Tabs In VFU ChannelsDec Code 27 98 m n1 … nk Tab Vertically Tab HorizontallyTab Horizontally Turn Double-Height Printing On/Off Turn Auto-wrap Around On/Off Turn Double-Width Printing On/Off Turn Double-Width, Double-Height Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn On/Off Ocrb Selection Turn Extending Table Character On/OffAscii Code Assc 0 z n Turn Proportional Mode On/Off Turn Proportional Mode On/OffTurn Underline On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Korean Standard Code Table KSC5601 Code Table Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Supplies Department Printronix Customer Support Center Appendix C Contact Information Corporate Offices Index Page Page 100 Page 179981-001