Divided Hangul Double Height | Printronix PSA3, P7000 H-Series

Chapter 3 Configuring The KSSM Emulation With Control Codes

Divided Hangul Double Height

ASCII Code	FS X n
Hex Code	28 58 n
Dec Code	1C 88 n
Purpose	Turns on/off divided double height printing of all characters as
	follows:
	n = 0	Turns off divided double height
	n = 1	Double height upper part of character
	n = 2	Double height lower part of character
	n = 3	Double height whole character
	Where:
	0 <= n <= 3
Comment	The line spacing of the line with upper part double height (set
	by FS X 1) will change to 24/180 inch.

The baseline of the line including double-height characters (set by FS X 3) moves down 24/180 inch, and the line spacing also increases 24/180 inch.

The default is Normal (non double-width double-height) printing.

Enable Printing of Upper Control Codes

ASCII Code	ESC 6
Hex Code	1B 36
Dec Code	27 54
Purpose	Tells the printer to treat codes 128 to 159 as printable
	characters instead of control codes.
Comment	This command affects the front panel setting of “Alt. Set 80-9F.”
	This command works in ASCII mode only.
	In the default mode, codes 128 to 159 are treated as printable
	characters.

42

Image 42

Printronix PSA3, P7000 H-Series manual Divided Hangul Double Height, Enable Printing of Upper Control Codes

Contents

Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table Software Features About This ManualRelated Product Information Software Features Introduction Control Panel Printing The Configuration Printing The Configuration Printing Configurations Step Key Result Allows you to make configuration changes Locks the Enter key Configuration Menu Configuration Menu Overview Moving Within The Configuration Menu Configuration MenuChanging Configurations Step Key Result To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus Menu CPI/LPI Select Font Attributes Margins Form LengthForm Width Perforation Skip Kssm Emulation Kssm Emulation Define CR Code Kssm Emulation Exceptions And Differences Default Values And States Factory Settings Characteristic Default Setting Escape Sequences FS Sequences Set And Reset Codes Configuring The Kssm Emulation With Control CodesSuper-Set Commands Format For Control Code Descriptions Control Code Index Setting the Page FormatSetting the Units Control Code Index Selecting Characters Control-code Character PrintingMechanical Control Hangul Extension Commands Printing GraphicsData and Memory Control Advance Print Position Vertically Align Sbcs Character with Dbcs Character Backspace Cancel The Alignment of Sbcs Character With Dbcs CharacterCancel The Alignment of Sbcs Character With Ascii Code Hex Code Dec Code Purpose Barcode Printing Ascii Hex Selects Barcode Barcode Printing Ascii Selects Value Offset unitInch UPC-A UPC-E EAN Carriage Return Cancel LineBeeper Beeper Define Pattern for Special Printing Effect Define User-Defined Character Define User-Defined Chinese Character Define User-Defined Chinese CharacterDelete Last Character in Buffer Hex Code Dec Code Enable Printing of Upper Control Codes Divided Hangul Double Height Enable Upper Control Codes Enable Upper Control CodesFont Expansion Form Feed Graphic Printing Graphics Printing Select Bit Image Initialize PrinterGraphics Printing Select Bit Image Line Feed Ascii Code ESC ! n Hex Code Master SelectMaster Select Bit On/Off Hex Dec Function Equivalent Master Select In Dbcs Mode Ascii Code FS ! n Hex Code Pair Two Characters in Vertical Printing Master Select One-Line Attribute In Dbcs ModeMaster Select One-Line Attribute In Dbcs Mode Bit On/Off Hex Dec Function Reassign Bit-image Mode Select 1/6-inch Line SpacingSelect 1/8-inch Line Spacing Select 15 CPI Select 10 CPISelect 12 CPI Select 10 CPI Select 60-dpi Graphics Select 120-dpi Graphics Select 240-dpi Graphics Select 120-dpi Graphics Select an International Character Set USA Select Bit Image Select Bit Image Cancel Bold Font Select Bold FontSelect Character Style Select Character Table Select Character TableSelect Condensed Printing Ascii Code ESC t n Hex Code Cancel Condensed Printing Select Double-strike Printing Cancel Double-strike PrintingSelect Dbcs Print Quality Select Dbcs Print Quality Cancel Double-width Printing One Line Select Double-width Printing One Line Select Double-width Printing in Dbcs Mode One Line Cancel Double-width Printing in Dbcs Mode One LineSelect Double-width Printing in Dbcs Mode One Select Hangul Myunjo/Gothic Style Select Dbcs ModeCancel Dbcs Mode Ascii Code Hex Code Select Print Quality Cancel Italic FontSelect Italic Font Select Italic Font Select Printer Deselect PrinterSelect Superscript/Subscript Printing Select Dbcs Super/Subscript Printing Cancel Superscript/Subscript PrintingCancel Superscript/Subscript Printing Select Vertical Printing Cancel Vertical Printing Select Horizontal Printing Set n/60-inch Line SpacingSet n/180-inch Line Spacing Set Bottom Margin Cancel Bottom MarginSet Absolute Horizontal Print Position Set Absolute Horizontal Print Position Set Horizontal Tabs Cancel Dbcs Character Half Width Super/Subscript PrintingSet Dbcs Character Half Width Ascii Code ESC D n1 n2 … nk NUL Set Intercharacter Space Set Intercharacter Space Set Left Margin Set Page Length In Inches Set Page Length In LinesSet Page Length In Inches Set Relative Horizontal Print Position Set Right Margin Set Vertical Tab Channels Set Vertical Tab ChannelsSet Vertical Tabs Ascii Code ESC B n1 n2 … nk NUL Set Vertical Tabs In VFU Channels Ascii Code ESC b m n1 … nk NULDec Code 27 98 m n1 … nk Tab Horizontally Tab VerticallyTab Horizontally Turn Auto-wrap Around On/Off Turn Double-Height Printing On/Off Turn Double-Width, Double-Height Printing On/Off Turn Double-Width Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn Extending Table Character On/Off Turn On/Off Ocrb SelectionAscii Code Assc 0 z n Turn Proportional Mode On/Off Turn Proportional Mode On/OffTurn Underline On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Customer Support Center Printronix Supplies Department Corporate Offices Appendix C Contact Information Index Page Page 100 Page 179981-001