Cancel Superscript/Subscript Printing | Printronix P7000 H-Series

Cancel Superscript/Subscript Printing

Cancel Superscript/Subscript Printing

ASCII Code	ESC T
Hex Code	1B 54
Dec Code	27 84
Purpose	Cancels super/subscript printing selected by the ESC S
	command.
Comment	The default is Normal (non-super/subscript) printing.

Select DBCS Super/Subscript Printing

ASCII Code	FS r n
Hex Code	28 72 n
Dec Code	1C 114 n
Purpose	Prints characters that follow at about ½ their normal width and
	½ their normal height; the printing location depends on the
	value of n as follows:
	n = 1 or 49Lower part of the character space
	n = 0 or 48Upper part of the character space
	Where:
	n = 0, 1, 48, 49
Comment	Use the FS DC2 command to cancel super/subscript printing.
	This command resets DBCS half-width printing set by the FS SI
	command.
	The default is Normal (non-super/subscript).

Select Vertical Printing

ASCII Code	FS J
Hex Code	28 4A
Dec Code	1C 74
Purpose	The character is printed in the same position with 90 degrees
	rotation in a counter-clockwise direction under Hangul mode.
Comment	Use the FS K command to cancel vertical printing.
	This command does not take effect on single-byte characters.
	The default is Normal (horizontal).

65

Image 65

Printronix P7000 H-Series, PSA3 manual Cancel Superscript/Subscript Printing, Select Dbcs Super/Subscript Printing

Contents

Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table Related Product Information Software FeaturesAbout This Manual Software Features Control Panel Introduction Printing The Configuration Printing The Configuration Allows you to make configuration changes Printing Configurations Step Key Result Locks the Enter key Configuration Menu Overview Configuration Menu Changing Configurations Step Key Result Moving Within The Configuration MenuConfiguration Menu To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus Menu CPI/LPI Select Font Attributes Form Width Form LengthMargins Perforation Skip Kssm Emulation Kssm Emulation Define CR Code Exceptions And Differences Kssm Emulation Factory Settings Characteristic Default Setting Default Values And States FS Sequences Escape Sequences Super-Set Commands Configuring The Kssm Emulation With Control CodesSet And Reset Codes Format For Control Code Descriptions Setting the Units Setting the Page FormatControl Code Index Control Code Index Mechanical Control Selecting CharactersControl-code Character Printing Data and Memory Control Hangul Extension CommandsPrinting Graphics Align Sbcs Character with Dbcs Character Advance Print Position Vertically Cancel The Alignment of Sbcs Character With Cancel The Alignment of Sbcs Character With Dbcs CharacterBackspace Ascii Code Hex Code Dec Code Purpose Ascii Hex Selects Barcode Barcode Printing Inch Barcode Printing Ascii Selects ValueOffset unit UPC-A UPC-E EAN Beeper Cancel LineCarriage Return Beeper Define User-Defined Character Define Pattern for Special Printing Effect Delete Last Character in Buffer Define User-Defined Chinese CharacterDefine User-Defined Chinese Character Hex Code Dec Code Divided Hangul Double Height Enable Printing of Upper Control Codes Font Expansion Enable Upper Control CodesEnable Upper Control Codes Graphic Printing Form Feed Graphics Printing Select Bit Image Graphics Printing Select Bit ImageInitialize Printer Line Feed Master Select Master SelectAscii Code ESC ! n Hex Code Bit On/Off Hex Dec Function Equivalent Ascii Code FS ! n Hex Code Master Select In Dbcs Mode Master Select One-Line Attribute In Dbcs Mode Master Select One-Line Attribute In Dbcs ModePair Two Characters in Vertical Printing Bit On/Off Hex Dec Function Select 1/8-inch Line Spacing Reassign Bit-image ModeSelect 1/6-inch Line Spacing Select 12 CPI Select 10 CPISelect 15 CPI Select 10 CPI Select 120-dpi Graphics Select 60-dpi Graphics Select 120-dpi Graphics Select 240-dpi Graphics USA Select an International Character Set Select Bit Image Select Bit Image Select Character Style Cancel Bold FontSelect Bold Font Select Condensed Printing Select Character TableSelect Character Table Ascii Code ESC t n Hex Code Cancel Condensed Printing Select Dbcs Print Quality Cancel Double-strike PrintingSelect Double-strike Printing Select Dbcs Print Quality Select Double-width Printing One Line Cancel Double-width Printing One Line Select Double-width Printing in Dbcs Mode One Select Double-width Printing in Dbcs Mode One LineCancel Double-width Printing in Dbcs Mode One Line Cancel Dbcs Mode Select Dbcs ModeSelect Hangul Myunjo/Gothic Style Ascii Code Hex Code Select Italic Font Cancel Italic FontSelect Print Quality Select Italic Font Select Superscript/Subscript Printing Select PrinterDeselect Printer Cancel Superscript/Subscript Printing Cancel Superscript/Subscript PrintingSelect Dbcs Super/Subscript Printing Select Vertical Printing Set n/180-inch Line Spacing Cancel Vertical Printing Select Horizontal PrintingSet n/60-inch Line Spacing Set Absolute Horizontal Print Position Cancel Bottom MarginSet Bottom Margin Set Absolute Horizontal Print Position Set Dbcs Character Half Width Cancel Dbcs Character Half Width Super/Subscript PrintingSet Horizontal Tabs Ascii Code ESC D n1 n2 … nk NUL Set Intercharacter Space Set Intercharacter Space Set Left Margin Set Page Length In Inches Set Page Length In InchesSet Page Length In Lines Set Right Margin Set Relative Horizontal Print Position Set Vertical Tabs Set Vertical Tab ChannelsSet Vertical Tab Channels Ascii Code ESC B n1 n2 … nk NUL Dec Code 27 98 m n1 … nk Set Vertical Tabs In VFU ChannelsAscii Code ESC b m n1 … nk NUL Tab Horizontally Tab HorizontallyTab Vertically Turn Double-Height Printing On/Off Turn Auto-wrap Around On/Off Turn Double-Width, Double-Height Printing On/Off Turn Double-Width, Double-Height Printing On/OffTurn Double-Width Printing On/Off Ascii Code Assc 0 z n Turn Extending Table Character On/OffTurn On/Off Ocrb Selection Turn Underline On/Off Turn Proportional Mode On/OffTurn Proportional Mode On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Korean Standard Code Table KSC5601 Code Table Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Supplies Department Printronix Customer Support Center Appendix C Contact Information Corporate Offices Index Page Page 100 Page 179981-001