Printronix P7000 H-Series, PSA3 p, hh

38

Chapter 3 Configuring The KSSM Emulation With Control Codes

Where:

P = activates printable data field variable

Where:

p

= location of PDF ('A' (above), 'B' (below, default), 'N' (none))

(Note: FIM, Postbar, and PDF417 do not support this

parameter.)

Where:

C = Calculate and plot check digit (if available as an option, the

default is No).

Check digit if the check digit is allowed to be optional)

Where:

H = activates the height variable

Where:

hh

= 2-digit barcode height in 1/10"

Where:

D = Dark barcode

(Note: This parameter does not take any effect under DBCS

typefaces.)

Barcode Type Magnification

Code 39

Interleaved 2/5

German I-2/5

UPC Shipping

Telepen

MSI

Code 128

UCC/ EAN-128

Code 93

UPS 11

UPC-A

UPC-E

EAN 8

EAN 13

Codabar

Postnet

Royal Mail

Postbar

FIM

PDF417

X4 X3 X2 X1 X1.5 X1A X1B *X1C *X1D *X1E

X4 X3 X2 X2A X1 X1A X1B

X4 X3 X2 X2A X1 X1A X1B

X4 X3 X2 X2A X1 X1A X1B

X4 X3 X2 X1 X1.5 X1A X1B *X1C *X1D *X1E

X4 X3 X2 X1

X4 X3 X2 X1 X1.5

X4 X3 X2 X1 X1.5

X4 X3 X2 X1 X1.5

X4 X3 X2 X1 X1.5

X2 X1

X2 X1

X2 X1

X2 X1

X4 X3 X2 X1

X1

X1 X1A

X1 X1A

X1

X3 X2 X1

*Note: the X1C, X1D, and X1E values can only be printed for horizontal

180dpi barcodes. If these values are sent for horizontal 120dpi barco des,

they will print as value X1.

Contents

Main Page Page Trademark Acknowledgements Table Of Contents 1 Introduction.............................................................9 2 Configuring With The Control Panel ..................... 11 3 LinePrinter Plus KSSM Emulation........................ 27 Page Page Page 1 About This Manual Warnings And Special Information Related Product Information Software Features Page 2 Control Panel IMPORTANT Introduction Chapter 2 Printing The Configuration Page Chapter 2 15 The Configuration Menu Figure 2. Configuration Menu Overview Moving Within The Configuration Menu Page Saving Your New Configuration Page Page LinePrinter Plus Menu 21 LinePrinter Plus Menu (see page 25) Figure 3. LinePrinter Plus Menu (see the next page) CPI/LPI Select Host Command Font Attributes Graphics Spd Up Page Format Reset Cmd CFG Ld Error Handling of Illegal Code Point KSSM Emulation 25 KSSM Emulation Figure 4. KSSM Emulation Menu Character Sets This parameter selects a character set for the KSSM emulation. CR Bold Select Define CR Code Auto LF Define LF Code Printer Select 20 CPI Condensed 3 Emulation KSSM Emulation Exceptions And Differences Chapter 3 Default Values And States Escape Sequences FS Sequences Super-Set Commands Set And Reset Codes Configuring The KSSM Emulation With Control Codes Format For Control Code Descriptions Control Code Index n1 n2 a1 a2 a3 m nL nH d1 t m nL nH d1 Advance Print Position Vertically Align SBCS Character with DBCS Character Cancel The Alignment of SBCS Character With DBCS Character Backspace Barcode Printing xxxx yyyy mmmm p hh q data q Beeper Cancel Line Carriage Return Define Pattern for Special Printing Effect Define User-Defined Character Define User-Defined Chinese Character a1 a2 a1a2 a1a2 d1 d2 d3 Divided Hangul Double Height Enable Printing of Upper Control Codes Enable Upper Control Codes Font Expansion Form Feed Graphic Printing Graphics Printing: Select Bit Image Initialize Printer Line Feed Master Select Master Select In DBCS Mode Master Select One-Line Attribute In DBCS Mode Pair Two Characters in Vertical Printing d Reassign Bit-image Mode m m Select 1/6-inch Line Spacing Select 1/8-inch Line Spacing Select 10 CPI Select 12 CPI Select 15 CPI Select 60-dpi Graphics Select 120-dpi Graphics Select 240-dpi Graphics Select an International Character Set Select Bit Image Select Bold Font Cancel Bold Font Select Character Style Select Character Table Select Condensed Printing Cancel Condensed Printing Select DBCS Print Quality Select Double-strike Printing Cancel Double-strike Printing Select Double-width Printing (One Line) Cancel Double-width Printing (One Line) Select Double-width Printing in DBCS Mode (One Line) Cancel Double-width Printing in DBCS Mode (One Line) Select DBCS Mode Cancel DBCS Mode Select Hangul Myunjo/Gothic Style Select Italic Font Cancel Italic Font Select Print Quality Select Printer Deselect Printer Select Superscript/Subscript Printing Cancel Superscript/Subscript Printing Select DBCS Super/Subscript Printing Select Vertical Printing Cancel Vertical Printing (Select Horizontal Printing) n Set /60-inch Line Spacing Set n /180-inch Line Spacing Set Absolute Horizontal Print Position Set Bottom Margin Cancel Bottom Margin Set DBCS Character Half Width Cancel DBCS Character Half Width and Super/Subscript Printing k n Set Horizontal Tabs Set Intercharacter Space Set Intercharacter Spacing of DBCS Character (Hangul Extension) Set Intercharacter Spacing Of SBCS Character (Hangul Extension) Set Left Margin Set Page Length In Inches Set Page Length In Lines Set Relative Horizontal Print Position Set Right Margin Set Vertical Tab Channels Set Vertical Tabs Set Vertical Tabs In VFU Channels Tab H ori zon tall y Tab Vertically Turn Auto-wrap Around On/Off Turn Double-Height Printing On/Off Turn Double-Width, Double-Height Printing On/Off Turn Double-Width Printing On/Off Turn Extending Table Character On/Off Turn On/Off OCRB Selection Turn Proportional Mode On/Off Turn Underline On/Off Turn Underline On/Off (Hangul Extension) A Set * ^ KEY Page Page Page Page Page Page Page Page Page Page Page Page Page C Printronix Customer Support Center Printronix Supplies Department Appendix C Corporate Offices Index A B C D G H I K L T U Z