Hardware Control | PSC SP400rf guide

INTERFACE

RS-232

HANDSHAKING

Review your system documentation to identify handshaking requirements, and use these labels to change the settings if required. The following brief descriptions explain each selection.

HARDWARE CONTROL

CTS/RTS Flow Control — is hardware handshaking. The scanner activates the RTS (Ready to Send) line when it is ready to send data to the host. The scanner waits for an active Clear to Send (CTS) signal from the host before transmitting data. If hardware control is disabled, CTS/RTS communication will not take place. If the host deactivates the CTS line during data trans- mission, the host will receive additional characters for no more than 2msec1.

CTS Scan Control — is also a hardware control. When scan control is enabled, label transmission is disabled until CTS is asserted and de-asserted.

1 Varies slightly depending upon baud rate selected.

18	SP400RF Programming Guide

Image 24

PSC SP400rf manual Hardware Control

Contents

Handheld Laser Scanner PSC Scanning, Inc Disclaimer Contents RS-232 Iii SP400RF Programming Guide Need to Understand the Basics Integrating Peripherals with Host Systems Changing Interfaces SP400RF Interface Groups Customizing Your Scanner Operation What is Programming MODE? HOW to Program Using BarcodesProgramming Overview Scanner Response When in Programming Mode Programming Session Return to Factory Settings Configuration UploadSET END Where to GO from Here IBM 4683/84 4693/94 Port 5B Settings IBM 4683/84 4693/94 Port 5B Interface SELECTION1 IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E Settings SET Send AS Code IBM 4682/92 Port E Settings IBM 4682/92 Port E Interface Selection PSC1 Ocia Interface Selection NCR Ocia Nine BIT Long Format Interface SelectionSNI Ocia Interface Selection SET NableIsable Nable Isable Full Ascii Wand Emulation Interface Selection LOW HighC128 END Communication Parameter RS-232 Interface SelectionSNI RS-232 Interface Selection Data Bits Start Bit Parity Bits Stop Bits Data Format Settings Hardware Control Software Control SET = N ONE = 90 Milliseconds = 100 Milliseconds PC Keyboard Wedge Interface Selection Type Eyboard Wedge Interface Intercharacter Delay = 55 Milliseconds Ibmxxxx STI Wedge STI Keyboard Wedge Interface Selection Label Transmit Format Configuration Items RS-232AND Keyboard Wedge Interfaces onlyPrefix & Suffix Label Transmit Format Config SET SET Prefix For the example in step four, scan 0, 2, 2 SET SET Suffix For the example in step five, scan 0, 7, 0 Setting a Single Character Prefix or Suffix ONE Character only ~ 7E Del Ascii Character SET UPC-A Our example, we would scan the UPC-A symbology label UPC-A UPC-EEAN-8 EAN-13 Code Codabar Interleaved 2 Standard 2 MSI/PLESSEY Scan the barcodes values Disabling Label I.D. for a Specific Symbology Label Transmit Format Config Interface Type UPC/EANCode Symbology Options Overview Symbology Selection Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Enable Codabar Disable Codabar Enable Code Disable Code Enable MSI/PLESSEY Disable MSI/PLESSEY UPC/EAN Options UPC/EAN Expansion Disabled END OptionalRequired Sendcheck Digit UPC-E SET EAN-8 Send Check Digit PRICE/WEIGHT Check Digit Code 39 Options Ascii Scan the Set Code 39 Minimum Label Length barcode Code 39 Minimum Label Length Interleaved 2 Enable DisableSET Dont Compute Compute Scan the Enable First Fixed barcode SET Fixed Engths Standard 2 Iata Standard 2 Normal or Iata Selection Dont Compute Dont Transmit Enable Disable Scan the Enable First Fixed barcode Standard 2 of 5 Fixed and Minimum Label Lengths Codabar Options Codabar Check Digit & Variable Length TRANSMIT1 Format = abcd/tn*eCodabar START/STOP Character Codabar Fixed Length SET Scan the Set Second Fixed Length label ONE Check Digit TWO Check DigitsMSI/PLESSEY Check Digit MSI/PLESSEY Fixed Length MSI/PLESSEY SET Fixed Lengths Code 128 Options General Features General Features Communications Protocol Enable Disable ACK/NAKItem on Not on File END STX/ETX BCD Ascii SET SET STX/ETX END SET STX SET ETX When to Acknowledge Wack RS-232 Feature only Wack ACK Option ① Option ➁ Option ➂ When to Beep Options SYNC2 NAK Wack ACK NAK SET Ption Beeper Volume OptionNormal Loud Channel Radio Channel Frequency Radio Transmit Power Wait Time for Host Acknowledge Wait Time Wait Time for Host Acknowledge Verify UPC-A Verify UPC-EVerify EAN-8 Verify EAN-13 Verify Code Verify Codabar Verify CodeVerify MSI/PLESSEY ONE Read TWO Reads Three Reads Four Reads LOW Battery Indication Method Beep Twice No Beep Factory Defaults EnableDisable UPC/EAN Code Disable Item ON/OFF File ACK/NAK ProtocolETX/STX High INTERFACE-DISCRETE Defaults RS-232/KEYBOARD WedgeNone ONE 100 IBM Interfaces Host Programming Creating Multifunction LabelsNeed More Information 102 UPC-A W/2 Digit ADD-ON UPC-A W/ 5 Digit ADD-ON UPC-E EAN-8 MSI/PLESSEY 104 Blank Asia Pacific AustraliaFrance Germany