QSB2340/2342 HBA Components | Q-Logic 2300 series instruction

Section 4

QSB2340/2342

4.1

QSB2340/2342 HBA Components

Figure 4-1identifies the QSB2340/2342 HBA components referenced throughout this section.

Each QSB2340/2342 HBA has a unique serial number, located on the back of the HBA. Take a minute to write down the serial number of the QSB2340/2342 HBA in the unlikely event that the NVRAM is corrupted.

J7 3 J8

SERIAL NUMBER

J10, J7, LED2

QSB2342

ONLY

ISP CHIP

PORT 2 1

PORT 1

PORT 2	J10
PORT 1	J9

LED2

LED1

J1

NOTE: The QLOGIC FPGA is on the back.

Figure 4-1. QSB2340/2342 HBA Layout

CF2351102-00 F

4-1

Image 41

Q-Logic 2300 series manual QSB2340/2342 HBA Components

Contents

SANblade 2300 Series User’s Guide Page Table of Contents Section QSB2340/2342 Figures Page What is Fibre Channel? How to Use this GuideIntroduction General Description Compliance with the following PCI standards QCP HBAs Features Hardware Hardware CF2351102-00 F LEDs QCP2330/2332QCP2330/2332 HBA Components Jumpers Installation and RemovalInstallation in the Computer Standard ApId Type Receptacle Occupant Condition Installation in the Computer Hot Swap System configuration is as follows FCode Removing the QCP2330/2332 HBA Updating FCode on the QCP2330/2332 HBA Setting the QCP2330/2332 HBA Connection ModeConnection mode and options display. For example Selecting the Boot Device Setting the QCP2330/2332 HBA Loop IDNew connection mode displays. For example Loop ID displays. For example Following displays Building the Bootable Disk QCP2330/2332 FCode Install the boot block on the new boot disk. For example Use the rm command to delete the restoresymtable file Boot from the newly created boot disk. For example Setting and Viewing the Fibre Channel Data RateView the current dump device setting. For example Shut down the system. Type the following Tables 2-2and 2-3define the QCP2330/2332 specifications Specifications Agency Certification LabelEMC/EMI Test Requirements Conducted Emission Product Safety Requirements QCP2340/2342 HBA Components QCP2340/2342 LED1 and LED2 QCP2342 Activity Installation in the Computer Hot Swap ApId Type Receptacle Occupant Condition System configuration is as follows Removing the QCP2340/2342 HBA Updating FCode on the QCP2340/2342 HBA Setting the QCP2340/2342 HBA Connection Mode Setting the QCP2340/2342 HBA Loop ID Selecting the Boot Device Building the Bootable Disk Use the rm command to delete the restoresymtable file Shut down the system. Type the following QCP2340/2342 Board Operating Environment Tables 3-3and 3-4define the QCP2340/2342 specifications DMA EMI and EMC Requirements EN550221995 Class a Radiated Emission QCP2340/2342 Agency Certification CF2351102-00 F QSB2340/2342 HBA Components QSB2340/2342 Installation in the Computer Updating FCode on the QSB2340/2342 HBA Setting the QSB2340/2342 HBA Loop ID Setting the QSB2340/2342 HBA Connection Mode For example Building the Bootable Disk QSB2340/2342 FCode Ufsdump 0f /ufstestore rf Shutdown the system. Type the following Tables 4-2and 4-3define the QSB2340/2342 specifications Class B QSB2340/2342 Agency Certification QSB2340/2342 Agency Certification CF2351102-00 F Problems After Installation TroubleshootingHardware Problem Checklist Fibre Channel Problem ChecklistPage Software II Software II-2 CF2351102-00 F Introduction Solaris Sparc Driver InstallationPre-installation Requirements Continue with in section Installing the Solaris Sparc Driver from a CD-ROM Press Enter to continue You are prompted to select a driver package. For example Installing QLogic QLA2300 driver as QLA2300 Type the following text to reboot and reconfigure the system Solaris Sparc Driver Installation FCode CF2351102-00 F