Quadra-Fire CASTILEI-MBK instruction

Castile Pellet Insert

R

C. Full Reline With Vertical Outside Air

NOTE: Check clearances carefully for this type of installation to ensure adequate room for outside air venting.

12” (305mm) min. above

12” (305mm) min. below

CAUTION

Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult local building, ﬁre ofﬁcials or authorities having jurisdiction about restrictions, installation inspection, and permits.

NOTE: In Canada, only a full reline is allowed per ULC S628-93, ORD ULC C1482-M1990.

NOTE; Use metal plate around exhaust vent pipe and seal all edges with non-flammable insulation such as mineral wool or ceramic.

Do not use high temperature caulk- ing materials to seal any edge to prevent future serviceability

Outside Air

Termination

at

Chimney Top

NOTE: In Canada this ﬁ replace insert must be installed with a continous chimney liner a 6 inch (152mm) in diameter extending from the ﬁ replace insert to the top of the chimney. The chimney liner must conform to the Class 3 requirments of CAN/ULC-S635, Standard for Lining Systems for Existing Masonry or Factory-Built Chimneys and Vents, or CAN/ULC-S640, Standard for Lining Systems for New Masonry Chimneys.

Figure 16.1

Page 16

7022-122

January 19, 2011

Image 16

Quadra-Fire CASTILEI-MBK owner manual Castile Pellet Insert Full Reline With Vertical Outside Air

Contents

Castile Pellet Insert Hot glass will cause burns Castile Pellet Insert Welcome to the Quadra-Fire Family Table of Contents Listing and Code Approvals Appliance Certiﬁcation BTU & Efﬁciency SpeciﬁcationsMobile Home Approved Glass Speciﬁcations Getting Started Appliance Location Castile Pellet Insert Locating Your Appliance & Chimney DraftNegative Pressure Minimum Vacuum Requirements 095 Negative Pressure, Shut-Down and Electrical Power Failure Castile Pellet Insert Avoiding Smoke and OdorsVent Conﬁgurations Outside Air Castile Pellet Insert Fire Safety Inspect Appliance & ComponentsTools And Supplies Needed Pre-Burn Check List 3Dimensions and Clearances Appliance Dimensions Castile Pellet Insert Clearance To Combustibles, UL and ULC Must be installed in a non-tapered enclosureShown with Rear Vent and Outside Air Masonry and Factory-Built Fireplaces Minimum Opening for Masonry and Factory-Built FireplacesCastile Pellet Insert Floor Protection Prefabricated Metal Chimney Using a saws-all, cut out the ﬂoor Altering the Factory-Built Fireplace Chimney and Exhaust Connection Vent InformationVenting Termination Requirements Castile Pellet Insert Pellet Venting Charts Minimum Vent for One ElbowHorizontalHori tal Run,RunftFT MinimumVertical Vent for Three Elbows 5Venting Systems Full Reline With Horizontal Outside Air Castile Pellet Insert Full Reline With Vertical Outside Air Mobile Home Installation 6Mobile Home 7Appliance Set-Up Outside Air Kit InstructionsLeveling System Ance. Shown in Figures 18.1 Castile Pellet Insert Door Handle Removal Adjustable Hearth SupportDoor Removal Ex the sides into a bowed position before installing 20.7 Surround & Trim Set, Econo 21.4 Castile Pellet Insert Surround & Trim Set, Econo Cont’d Surround and Cast Trim SetPiece. Figure Shown in Figure .2 on Two Piece Log Set Installation Castile Pellet Insert Thermostat Installation Combustible/Non-Combustible Materials Operating InstructionsFuel Material and Fuel Storage Castile Pellet Insert General Operating Information Before Your First FireClear Space Thermostat Calls For Heat Feed Rate Adjustment Instructions Fire CharacteristicsCastile Pellet Insert Starting Your First Fire Frequently Asked Questions Castile Pellet Insert Ignition Cycles Turn down thermostat and let the appliance completely cool Page Symptom Possible Cause Corrective Action Quick Reference Maintenance Chart Maintaining & Servicing Your ApplianceTypes of Fuel Frequency Cleaning Firepot with Cleaning Rod & Firepot Clean-Out Tool Cleaning Ash DrawerSee .1 on Ash Removal from Firebox Disposal of Ashes Frequency As needed Cleaning Heat Exchanger Tubes Cleaning Beneath Heat ExchangerCleaning the Glass Door Latch Inspection Cleaning the Hopper Cleaning Exhaust Blower Requires No LubricationCleaning Convection Blower Requires No Lubrication Preparing Firebox for Non-Burn Season Castile Pellet Insert High Ash Fuel Maintenance Immediate Attention and Cleaning is Required Castile Pellet Insert Combustion Blower Replacement Convection Blower Replacement Castile Pellet Insert Igniter Replacement Glass Replacement Re-installing Bafﬂe & Brick Set Castile Pellet Insert Bafﬂe & Brick Set Removal Castile Pellet Insert Re-installing Bafﬂe & Brick Set Cont’d Reference Materials Component Function Vacuum Switch Wiring Schematic See .1 belowThermostat Snap Disc #1 Convection Blower 110F Cleaning Rods & Heat Exchanger Tubes Castile Pellet Insert Component Locations Part number list on following pages Service PartsCastile Pellet Insert At Depot Stocked #28 Feed Assembly #23 Door AssemblyStocked at Depot Stocked #38 Firepot and Associted Parts Optional Accessories SP-CSTLI5134 Description Comments Part Number Fasteners Service And Maintenance Log Service And Maintenance Log Cont’d Homeowner’s Notes Limited Lifetime Warranty Warranty Conditions Contact Information