Quadra-Fire CASTILEI-MBK guide

Castile Pellet Insert

R

J. Thermostat Installation

1. A 12 volt AC thermostat is required to operate this pellet appliance. You may use the included wall mount thermo- stat or purchase an optional programmable thermostat or remote control.

The included thermostat is equipped with an adjustable heat anticipator. The current rating is .05 amps. The anticipator needs to be adjusted to the lowest setting available.

2.When mounting a thermostat on a wall, be sure to follow your thermostat installation instructions carefully.

NOTE: Thermostat must be mounted level for accu- rate readings. The thermostat should be mounted on an inside wall and not in direct line with the appliance convection air. Remove any packaging from inside the thermostat before using.

NOTE: If the thermostat is located too close to the appliance, you may need to set the temperature setting slightly higher to maintain the desired tem- perature in your home.

CAUTION

Shock hazard.

•Do NOT remove grounding prong from plug.

•Plug directly into properly grounded 3 prong receptacle.

•Route cord away from appliance.

•Do NOT route cord under or in front of appli- ance.

	Red Call		Control Box
	Light
	Fuse
				Power Cord
				Outlet
		Blue	Light
		Blue		Light
	Red/Green/Amber			Light
Heat Output	Red/Green/Amber
Heat Output
Switch
Firepot Cleaning Rod				Thermostat
Reset Button				Thermostat
	Junction Box			Block
	Junction Box

Figure 24.1

Page 24

7022-122

January 19, 2011

Image 24

Quadra-Fire CASTILEI-MBK owner manual Castile Pellet Insert Thermostat Installation

Contents

Castile Pellet Insert Hot glass will cause burns Castile Pellet Insert Welcome to the Quadra-Fire Family Table of Contents Listing and Code Approvals Appliance Certiﬁcation BTU & Efﬁciency SpeciﬁcationsMobile Home Approved Glass Speciﬁcations Getting Started Appliance Location Castile Pellet Insert Locating Your Appliance & Chimney DraftNegative Pressure Minimum Vacuum Requirements 095 Negative Pressure, Shut-Down and Electrical Power Failure Castile Pellet Insert Avoiding Smoke and OdorsVent Conﬁgurations Outside Air Castile Pellet Insert Fire Safety Inspect Appliance & ComponentsTools And Supplies Needed Pre-Burn Check List 3Dimensions and Clearances Appliance Dimensions Must be installed in a non-tapered enclosure Castile Pellet Insert Clearance To Combustibles, UL and ULCShown with Rear Vent and Outside Air Masonry and Factory-Built Fireplaces Minimum Opening for Masonry and Factory-Built FireplacesCastile Pellet Insert Floor Protection Prefabricated Metal Chimney Using a saws-all, cut out the ﬂoor Altering the Factory-Built Fireplace Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Castile Pellet Insert Pellet Venting Charts Minimum Vent for One ElbowHorizontalHori tal Run,RunftFT MinimumVertical Vent for Three Elbows 5Venting Systems Full Reline With Horizontal Outside Air Castile Pellet Insert Full Reline With Vertical Outside Air Mobile Home Installation 6Mobile Home 7Appliance Set-Up Outside Air Kit InstructionsLeveling System Ance. Shown in Figures 18.1 Adjustable Hearth Support Castile Pellet Insert Door Handle RemovalDoor Removal Ex the sides into a bowed position before installing 20.7 Surround & Trim Set, Econo 21.4 Castile Pellet Insert Surround & Trim Set, Econo Cont’d Surround and Cast Trim SetPiece. Figure Shown in Figure .2 on Two Piece Log Set Installation Castile Pellet Insert Thermostat Installation Operating Instructions Combustible/Non-Combustible MaterialsFuel Material and Fuel Storage Castile Pellet Insert General Operating Information Before Your First FireClear Space Thermostat Calls For Heat Fire Characteristics Feed Rate Adjustment InstructionsCastile Pellet Insert Starting Your First Fire Frequently Asked Questions Castile Pellet Insert Ignition Cycles Turn down thermostat and let the appliance completely cool Page Symptom Possible Cause Corrective Action Quick Reference Maintenance Chart Maintaining & Servicing Your ApplianceTypes of Fuel Frequency Cleaning Firepot with Cleaning Rod & Firepot Clean-Out Tool Cleaning Ash DrawerSee .1 on Ash Removal from Firebox Disposal of Ashes Frequency As needed Cleaning Heat Exchanger Tubes Cleaning Beneath Heat ExchangerCleaning the Glass Door Latch Inspection Cleaning the Hopper Cleaning Exhaust Blower Requires No LubricationCleaning Convection Blower Requires No Lubrication Preparing Firebox for Non-Burn Season Castile Pellet Insert High Ash Fuel Maintenance Immediate Attention and Cleaning is Required Castile Pellet Insert Combustion Blower Replacement Convection Blower Replacement Castile Pellet Insert Igniter Replacement Glass Replacement Re-installing Bafﬂe & Brick Set Castile Pellet Insert Bafﬂe & Brick Set Removal Castile Pellet Insert Re-installing Bafﬂe & Brick Set Cont’d Reference Materials Component Function Vacuum Switch Wiring Schematic See .1 belowThermostat Snap Disc #1 Convection Blower 110F Cleaning Rods & Heat Exchanger Tubes Castile Pellet Insert Component Locations Service Parts Part number list on following pagesCastile Pellet Insert At Depot Stocked #23 Door Assembly #28 Feed AssemblyStocked at Depot Stocked #38 Firepot and Associted Parts Optional Accessories SP-CSTLI5134 Description Comments Part Number Fasteners Service And Maintenance Log Service And Maintenance Log Cont’d Homeowner’s Notes Limited Lifetime Warranty Warranty Conditions Contact Information