3Dimensions and Clearances | Quadra-Fire CASTILEI-MBK guide

R

Castile Pellet Insert

3Dimensions and Clearances

A. Appliance Dimensions

27-7/8 in. (707mm)

23-3/8 in. (594mm)

8 in.

(203mm)

32-1/4 in. (819mm)

Figure 9.1 - Top View

	24-3/4 in.		19 in.
	(629mm)		(483mm)
	9-3/4 in.	13 in.	2 in.
	(249mm)	(330mm)	2 in.
	(249mm)	(330mm)	(51mm)
			(51mm)

Figure 9.2 -Side View

A

B

Figure 9.3- Front View

	Overall Size		A	B
	Metal Surround w/Cast Trim, STD		42-1/2 in. (1080mm)	30 in. (762mm)
	Metal Surround w/Cast Trim, LRG		48 in. (1219mm)	34 in. (864mm)
	Metal Surround w/Standard Trim, STD		43 in. (1092mm)	31 in. (787mm)
	Metal Surround w/Standard Trim, LRG		51 in. (1294mm)	34 in. (864mm)


January 19, 2011		7022-122			Page 9

Image 9

Quadra-Fire CASTILEI-MBK owner manual 3Dimensions and Clearances, Appliance Dimensions

Contents

Hot glass will cause burns Castile Pellet Insert Welcome to the Quadra-Fire Family Castile Pellet Insert Table of Contents Appliance Certiﬁcation BTU & Efﬁciency Speciﬁcations Listing and Code ApprovalsMobile Home Approved Glass Speciﬁcations Appliance Location Getting Started Draft Castile Pellet Insert Locating Your Appliance & ChimneyNegative Pressure Minimum Vacuum Requirements 095 Castile Pellet Insert Avoiding Smoke and Odors Negative Pressure, Shut-Down and Electrical Power FailureVent Conﬁgurations Outside Air Inspect Appliance & Components Castile Pellet Insert Fire SafetyTools And Supplies Needed Pre-Burn Check List Appliance Dimensions 3Dimensions and Clearances Must be installed in a non-tapered enclosure Castile Pellet Insert Clearance To Combustibles, UL and ULCShown with Rear Vent and Outside Air Minimum Opening for Masonry and Factory-Built Fireplaces Masonry and Factory-Built FireplacesCastile Pellet Insert Floor Protection Prefabricated Metal Chimney Altering the Factory-Built Fireplace Using a saws-all, cut out the ﬂoor Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Minimum Vent for One Elbow Castile Pellet Insert Pellet Venting ChartsHorizontalHori tal Run,RunftFT MinimumVertical Vent for Three Elbows Full Reline With Horizontal Outside Air 5Venting Systems Castile Pellet Insert Full Reline With Vertical Outside Air 6Mobile Home Mobile Home Installation Outside Air Kit Instructions 7Appliance Set-UpLeveling System Ance. Shown in Figures 18.1 Adjustable Hearth Support Castile Pellet Insert Door Handle RemovalDoor Removal 20.7 Ex the sides into a bowed position before installing 21.4 Surround & Trim Set, Econo Surround and Cast Trim Set Castile Pellet Insert Surround & Trim Set, Econo Cont’dPiece. Figure Shown in Figure .2 on Two Piece Log Set Installation Castile Pellet Insert Thermostat Installation Operating Instructions Combustible/Non-Combustible MaterialsFuel Material and Fuel Storage Before Your First Fire Castile Pellet Insert General Operating InformationClear Space Thermostat Calls For Heat Fire Characteristics Feed Rate Adjustment InstructionsCastile Pellet Insert Starting Your First Fire Castile Pellet Insert Ignition Cycles Frequently Asked Questions Turn down thermostat and let the appliance completely cool Page Symptom Possible Cause Corrective Action Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartTypes of Fuel Frequency Cleaning Ash Drawer Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolSee .1 on Ash Removal from Firebox Disposal of Ashes Frequency As needed Cleaning Beneath Heat Exchanger Cleaning Heat Exchanger TubesCleaning the Glass Door Latch Inspection Cleaning Exhaust Blower Requires No Lubrication Cleaning the HopperCleaning Convection Blower Requires No Lubrication Preparing Firebox for Non-Burn Season Immediate Attention and Cleaning is Required Castile Pellet Insert High Ash Fuel Maintenance Convection Blower Replacement Castile Pellet Insert Combustion Blower Replacement Glass Replacement Castile Pellet Insert Igniter Replacement Castile Pellet Insert Bafﬂe & Brick Set Removal Re-installing Bafﬂe & Brick Set Castile Pellet Insert Re-installing Bafﬂe & Brick Set Cont’d Component Function Reference Materials Wiring Schematic See .1 below Vacuum SwitchThermostat Snap Disc #1 Convection Blower 110F Castile Pellet Insert Component Locations Cleaning Rods & Heat Exchanger Tubes Service Parts Part number list on following pagesCastile Pellet Insert Stocked At Depot #23 Door Assembly #28 Feed AssemblyStocked at Depot #38 Firepot and Associted Parts Stocked Optional Accessories SP-CSTLI5134 Description Comments Part Number Fasteners Service And Maintenance Log Service And Maintenance Log Cont’d Homeowner’s Notes Limited Lifetime Warranty Warranty Conditions Contact Information