CB1200-I Pellet Insert Component Locations | Quadra-Fire CB1200I-B

R

CB1200-I Pellet Insert

B. Component Locations

		Terminal Block
		Center 2 Screws for
Heat Output	Control Box	Thermostat Wires
Heat Output
Switch
Reset Button	Blue
	Blue
Red Call Light	Blinking
Red Call Light	Light
Fuse	Red/ Green
	Red/ Green
	Light	Power Outlet

Figure 37.1

Beginning Manufacture Date: April 8, 1999

	4	3
		14
		2
5		1
		1
		13
11	12
	12

Figure 37.4 - Door, Face, Glass, & Latch Assembly

Exhaust

Transition

Assembly

Convection Exhaust

Blower Blower

Figure 37.2

	Nbr	Description		Part Number
	11	Door Frame		MBK:	410-6300
				Gold:	410-5530
				Nickel: 510-5530
	12	Glass Assembly, Center		510-5400
	13	Glass Assembly, Sides		510-5410
	1	Glass Frame Post		410-6240
	2	Glass Frame Side		410-4740
	14	Door Latch Bracket		410-4912
	3	Glass Frame Spacer		410-6250
	4	Glass Frame, Top & Bottom		410-4730
	5	Hinge, Female		450-2910

	Glass Size Center: 13-7/8” wide x 11” high
	Glass Size Sides:		5-1/8” wide x 11” high

C. Exploded Views

	6
					Nbr	Description	Part Number
					40	Firepot Pull Rod (Linkage)	812-4140
		8			42	Igniter Bracket	Not Replaceable
			39		7	Thumb Screw	7000-223
			39		43	Igniter (Heating Element)	7000-226
				41	43	Igniter (Heating Element)	7000-226
				41	41	Firepot, EZ Clean	812-3351
					41	Firepot, EZ Clean	812-3351
	42	7			39	Thermocouple Holder	812-3171
40	42				8	Thermocouple	812-0210
40

		43			36	Thermocouple Cover	812-1322
Figure 37.3 - Firepot Assembly
October 26, 2006					7014-083C		Page 37

Image 37

Quadra-Fire CB1200I-B CB1200-I Pellet Insert Component Locations, Exploded Views, Beginning Manufacture Date April 8

Contents

CB1200I-B CB1200-I Pellet Insert Welcome to the Quadra-Fire Family Table of Contents Listing and Code Approvals Fire Safety Design, Installation & Location ConsiderationsGetting Started Appliance Location Measuring Standards CB1200-I Pellet Insert Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List Appliance Dimensions Dimensions and Clearances Inch 0mm Clearance to Exposed Section and Face Trim Shown with Rear Vent and Optional Outside Air Face Trim Floor Protection CB1200-I Pellet Insert Masonry Minimum OpeningCalculating Alternate Floor Protection Material Starter hole Mark area of floor to cut Vent Information Install vent at clearances specified byVent manufacturer CB1200-I Pellet Insert Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems CB1200-I Pellet Insert Full Reline With Outside Air You must use a Quadra-Fire Outside Air Kit for instal Mobile Home InstallationLation in a mobile home Appliance Set-Up Rear Shroud Installation Installing Rear Shroud Attaching Shroud to Hopper Body Rear Vent Installation PreparationFor Top Vent Installation Optional Grille Installation Adjustable Hopper OptionsTo adjust hopper CB1200-I Pellet Insert Outside Air Kit Instructions Size 9d x 45w, 2 to 10 Height Adjustment CB1200-I Pellet Insert Adjustable Hearth Support CB1200-I Pellet Insert Panel and Trim Set Completed View CB1200-I Pellet Insert Panel and Trim Set Cont’d Charred Areas in the Back Fuel Size And Material General Operating Information Operating Instructions Fire Characteristics Fuel Adjustment Control RodFeed Rate Adjustment Instructions CB1200-I Pellet Insert Before Your First Fire Do not Leave Firepot Floor Open Frequently Asked Questions Symptom TroubleshootingPossible Cause Corrective Action Page Page Pellet Insert CB10Maintaining & Servicing Your Appliance Cleaning Beneath Heat Exchanger Cleaning Heat Exchanger ChambersCleaning Exhaust Path Cleaning the Glass Frequency As needed High Ash Fuel Content Maintenance Igniter Replacement Replacing Center Glass Top frame when removing and replacing center GlassReplacing Side Glass Ered Phillips head screw driver to remove Screws Component Function Reference Materials Wiring Harness See .1 below Vacuum SwitchSnap Disc #1 Convection Blower 125F Snap Disc #2 Fuel Delivery Interrupt 200F Exploded Views CB1200-I Pellet Insert Component LocationsBeginning Manufacture Date April 8 Glass Size Center 13-7/8 wide x 11 high Glass Size Sides Beg. Manufacture Date July Nbr Description CB1200-I Pellet Insert Service Parts and AccessoriesItem # Part Descsription, Alphabetical Order 7014-083C October 26 Appliance Item No Accessories Date of Service Performed By Description of Service CB1200-I Pellet Insert Service And Maintenance Log CB1200-I Pellet Insert Warranty Policy Lifetime Warranty Telephone CB1200-I Pellet Insert