Quadra-Fire CB1200I-B Vent Information, Chimney and Exhaust Connection, CB1200-IPellet Insert

CB1200-I Pellet Insert				R
A.4		Vent Information
	Chimney and Exhaust Connection		B. Venting Termination Requirements
1.	Chimney & Connector: Use 3 or 4 inch (76-102mm)			CAUTION
	diameter type "L" or "PL" venting system. It can be vented
	vertically or horizontally.			Do not terminate vent in any enclosed or semi-enclosed
2.	Mobile Home: Approved for all listed pellet vent. Use			area such as a carport, garage, attic, crawl space, under a
	listed double wall flue connector. A Quadra-Fire Outside			sun deck or porch, narrow walkway or closely fenced area,
	Air Kit must be used with manufactured home installa-			or any location that can build up a concentration of fumes
	tions.			such as a stairwell, covered breezeway, etc.
3. Residential: Use 24 gauge single wall flue connector or
			1. Termination must exhaust above air inlet elevation. It is
	listed double wall flue connector to Class A listed metal
				recommended that at least 60 inches (1524mm) of verti-
	chimneys, or masonry chimneys meeting national and/or
				cal pipe be installed when appliance is vented directly
	local codes for solid fuel appliances.
				through a wall. This will create a natural draft, which
4. Install vent at clearances specified by the				will help prevent the possibility of smoke or odor venting
	vent manufacturer.			into the home during a power outage. It will also keep
5. Secure exhaust venting system to the appliance with at				exhaust from causing a nuisance or hazard by exposing

least 3 screws. Also secure all connector pipe joints with	people or shrubs to high temperatures. The safest and
	preferred venting method is to extend the vent vertically
at least 3 screws through each joint.
	through the roof.

NOTE: All pipe must be welded seam pipe whenever pos- sible. Seal pipe joints with high temperature silicone (500°F [260°C] minimum rated only).

NOTE: If burning shelled field corn, you must use approved venting specifically designed for corn. Follow the instruc- tions from the venting manufacturer.

WARNING

Fire Risk.

•Only LISTED venting components may be used.

•NO OTHER vent components may be used. Substitute or damaged vent components may impair safe operation.

WARNING

Vent surfaces get HOT, can cause burns if touched. Non-combustible shielding or guards may be required

2. Distance from doors and opening windows, or gravity or ventilation air inlets into building:

a.Not less than 48 inches (1219mm) below;

b.Not less than 48 inches (1219mm) horizontally from;

c.Not less than 12 inches (305mm) above.

3.Distance from permanently closed windows:

a.Not less than 12 inches (305mm) below, horizontally from or above.

4. Distance between bottom of termination and grade should be 12 inches (305mm) minimum. This is con- ditional upon plants in the area, and nature of grade surface. The grade surface must be a non-combustible material (i.e., rock, dirt). The grade surface must not be lawn. Distance between bottom of termination and public walkway should be 84 inches (2134mm) minimum.

5. Distance to combustible materials must be 24 inches (610mm) minimum. This includes adjacent buildings, fences, protruding parts of the structure, roof overhang, plants and shrubs, etc.

6.Termination Cap Location (Home Electrical Service)

•Side-to-side clearance is to be the same as minimum clearance to vinyl inside corners.

•Clearance of a termination cap below electrical service shall be the same as minimum clearance to vinyl soffits.

•Clearance of a termination cap above electrical service will be 12 inches (305mm) minimum.

•Location of the vent termination must not obstruct or interfere with access to the electrical service.

Page 12 7014-083C October 26, 2006