Quadra-Fire QFP44 Adjusting the Flame Height Operates in on or Thermo mode, Low/Battery Indicator

Adjusting the Flame Height -

Operates in ON or THERMO mode

This remote control system allows the user to control the height of the FLAME when the gas valve is factory equipped with a FLAME CONTROLLER.

• Press and release FLAME button to change ame height to HI (see Figure 2.6, Location #5), a second ame icon appears.

•Press again to return ame to normal state.

Low/Battery Indicator

An “X” outlined by a battery on the right side of the LCD screen will appear when battery power has dropped sig- ni cantly. At this time, approximately two weeks of battery power remains.

Child Proof Lockout (CP)

The transmitter contains a “Child Proof” lockout feature that prevents unauthorized use of the remote control. To access the “Child Proof” activation button, remove cover on BACK of transmitter. To activate LOCKOUT:

•Press and hold in the “setting button” for 5 seconds (see Figure 2.7). The letters CP will display on the LCD screen). This prevents the activation of replace. When any function button is pressed ON/OFF etc. the letter CP will display on the LCD screen.

To deactivate LOCKOUT:

•Press and hold in the “setting button” for 5 seconds. The LCD will display CP until 5 seconds have elapsed, and then the LCD screen will return to its normal state.

Transmitter Safety Features

It is recommended that the TRANSMITTERS always be located within a 20 foot operating range of the replace, preferably in the same room in which the replace system is located. The TRANSMITTER features several safety features that alert the user when the TRANSMITTER is placed outside the 20 foot normal operating range.

Thermo-Updating and Communication-Safety Features

This remote control has a COMMUNICATION-SAFETY function built into its software. It provides an extra margin of safety when the TRANSMITTER is out of the normal

20 foot operating range of the receiver. It is also activated when the batteries become weak or are removed from the transmitter.

In the THERMO-UPDATING feature (only in the THER- MO or TIMER modes) the transmitter normally reads the ROOM temperature every 2 minutes. In addition to check- ing the temperature, the transmitter sends a signal to the receiver indicating that the transmitter and its batteries are still active.

In the COMMUNICATION-SAFETY feature, at all times and in all OPERATING MODES the transmitter sends a

signal every 15 minutes to the receiver, indicating that the transmitter is within the normal operating range of 20 feet.

Should the receiver NOT receive a transmitter signal every 15 minutes (COMMUNICATION-SAFETY feature), the RECEIVER will begin a 2 HOUR (120 minute) count- down timing function. If during this 2 hour period, the re- ceiver does not receive a signal from the transmitter, the RECEIVER will shut down the replace being controlled by the receiver. The RECEIVER will then emit a series of rapid “beeps”. Then, after 10 rapid “beeps”, the RECEIV- ER will continue to emit a single “beep” every 4 seconds until a transmitter signal is again received. The intermit- tent 4 second beeping will go on inde nitely until reset.

To “reset” the RECEIVER and operate the replace sys- tem:

•Press the MODE button on the transmitter. The word ON must display on the LCD screen. The COMMUNICATION -SAFETY operation is overridden and the system will return to normal operation depending on the MODE selected at the transmitter. We recommend the user check the batteries in the TRANSMITTER to make sure the voltage is no less than 2.7 volts.

Auto Shutdown

This remote control has an Auto Shutdown feature incor- porated into its system. When the transmitter MODE is in the ON position the replace will continuously operate for 9 hours. After 9 hours, the replace will shut down. To relight the replace:

•Press the MODE button. The replace will operate continuously for up to 9 hours before Auto Shutdown repeats cycle. The Auto Shutdown signal comes from the transmitter. The transmitter must be positioned within a 20 ft operating range for the Auto Shutdown feature to operate.

System Check

Light the appliance following the lighting instructions that came with the replace. Con rm that the pilot ame is on. It must be in operation for the main gas valve to operate.

•Slide the 3-position button on the remote receiver to the ON position. The main gas ame (i.e., the re) should ignite.

•Slide the button to OFF. The ame should extinguish (the pilot ame will remain on).

•Slide the button to REMOTE (the center position), then press the MODE button on the transmitter to change the system to ON. The main gas ame should ignite.

•Press the MODE button on the transmitter to change the system to OFF. The ame should extinguish (the pilot ame will remain on).

•Press the MODE button on the transmitter to change the system to THERMO.

Quadra-Fire • QFP44 • 4051-300 Rev M • 09/08 15