B. Facing Material

•The QFP44 is shipped with non-combustible material in place. Do not cover or replace this non-combustible material with combustible materials.

-The non-combustible front upper can be removed if replaced with non-combustible materials. See Section 1.E. for materials that may be used.

• Combustible nish wall material may be butted up to the unit and the supplied non-combustible material of the upper front.

-The unit is shipped with door templates attached. The wall material should go behind the templates and butt up to the edge of the unit. Refer to Figure 13.4.

•The joints at the non-combustible material may be taped and covered with normal joint compound.

•Seal joints between the nished wall and appliance top and sides using a 300 °F minimum sealant. Refer to Figure 13.3.

WARNING! Risk of Fire! DO NOT apply combustible ma- terials beyond the minimum clearances. Comply with all minimum clearances to combustibles as speci ed in this manual. Overlapping materials could ignite and will inter- fere with proper operation of doors and louvers.

•Sheetrock/wall material will have been installed (see Figure 11.1) and the joints lled as per Section 3.B.

•

If installing doors with an outside surface t, the facing

 

templates should be removed (retain the screws for

 

door installation) and non-combustible facing material

 

less than one inch thick may be brought to the edge of

 

the replace opening. Doors will be mounted over the

 

facing material. The door frame is slotted to allow the

 

door to be mounted up to one inch from the surface of

 

the unit.

•

If installing doors with a recessed t, facing material

 

must be butted to the anges of the facing templates

 

to allow doors to t within the facing material. Once the

 

facing material is in place, the template must be removed

Finish wall material may be combustible - Top and Sides

0 in.

Non-Combustible Zone

 

 

These joints

 

may be taped

 

and covered

 

with joint

 

compound.

0 in.

0 in.

High Temperature Sealant (300° F/149° C min.)

Figure 13.3 Noncombustible Facing Diagram

Template

Pieces

Figure 13.4 Facing Template

(retain the screws for door installation).

C. Facing Template Removal

There is a metal template on each side and across the top of the door opening. See Figure 13.4. If using an inside t for the doors, do not remove the templates until the facing material is installed. If you choose to use an outside t, the templates may be removed before install- ing the facing material.

•Side Templates – Remove the screws from the sides of the door opening and set aside. Remove and discard the template pieces.

•Top Template – Loosen the screws across the top of the opening. Slide the top template out, discard the template and tighten the screws.

D. Mantel

Mantel

Non-combustible

Face

A = 53 in. (1346 mm) min.

Non-combustible Mantel

A = 66 in. (1676 mm) min.

Combustible Mantel

12 in. (308 mm) maximum depth

A

The mantel may be constructed with combustible or non- combustible materials as indicated in Figure 13.5

Figure 13.5 Minimum Mantel Heights

52

Quadra-Fire • QFP44 • 4051-300 Rev M • 09/08

Page 51 Page 53
Page 52
Image 52
Quadra-Fire QFP44 owner manual Facing Material, Facing Template Removal, Mantel
Page 51 Page 53

QFP44 specifications

The Quadra-Fire QFP44 is a highly efficient and versatile pellet stove designed to provide warmth and comfort while offering a range of advanced features and technologies. It stands out in the market for its blend of efficiency, user-friendly operation, and aesthetic appeal.

One of the key features of the QFP44 is its impressive heat output. With a heating capacity of up to 2,500 square feet, it is suitable for medium to larger living spaces, making it an ideal choice for families looking for an effective heating solution. The stove boasts an adjustable output, allowing users to set the heat level according to their specific needs, which promotes energy efficiency and enhances comfort.

The QFP44 utilizes a patented feed system that ensures a consistent and reliable supply of pellets for combustion. This technology not only maximizes fuel efficiency but also minimizes the need for frequent refueling. In addition, the stove features a large hopper capacity, capable of holding up to 45 pounds of pellets. This translates into longer burn times, enabling users to enjoy hours of warmth without constant supervision.

Another notable characteristic of the QFP44 is its advanced control system. The innovative electronic control board allows users to monitor and adjust the stove settings easily. The system includes programmable temperature settings, which enable homeowners to schedule heating times according to their lifestyle. This convenience makes the stove ideal for those who want to return to a warm home without wasting energy.

The QFP44 is also engineered with a clean-burning technology that significantly reduces emissions. This feature not only makes the stove environmentally friendly but also enhances its safety profile. The high-efficiency combustion system effectively converts pellets into heat with minimal smoke and pollutants, fulfilling strict environmental standards.

For aesthetic appeal, the QFP44 is designed with a contemporary look, featuring a large viewing window that allows users to enjoy the beautiful ambiance of the flame. The stove is available in various finishes, making it a stylish addition to any home décor.

Overall, the Quadra-Fire QFP44 combines efficiency, user-friendly technology, and an elegant design, making it a top choice for anyone seeking an effective and attractive pellet heating solution. Its blend of features ensures homeowners can enjoy both comfort and convenience during the cold months while maintaining an environmentally responsible heating option.
Top Page Image Contents