Expanding Your Phone | Radio Shack 43-3704 manual

Expanding Your Phone

! IMPORTANT !

If you purchase a 43-3705 extra handset, please register the handset to the original/main base before use. The 43-3705 will not operate until it is registered.

Ô NOTES Ô

•All of the handsets ring when a call is received.

•An extra handset can be registered when the main base is in standby mode.

EXPANDING YOUR PHONE

Dual Handset Expandability

Your phone supports another handset in addition to the supplied. You can now place a fully-featured cordless handset anywhere AC power is available to connect the handset charger. !

Handsets can be used in DirectLink Mode or on an intercom call without interfering with incoming calls. It is possible to have a four-way conference among two handsets and both outside lines. All of the handsets ring when a call is received.

REGISTER THE HANDSET TO THE BASE

If you purchase an extra handset, you need to register the handset to the base before use. Only one handset can be registered at a time. ! Ô

Handset supplied with the phone is registered to the base by the factory. When charged, pre-registered handset displays a handset ID number. Handset that has not been registered displays Place handset on main base to register. When you register an extra handset to the base, the handset ID will be assigned.

1.Before registering the extra handset, the battery pack MUST be charged for 15-20 hours.

2.Place the extra handset in the main base unit to begin registration.

3.While the handset is registering,

Handset Registering will appear in the LCD.

50

Image 50

Radio Shack 43-3704 owner manual Expanding Your Phone, Dual Handset Expandability, Register the Handset to the Base

Contents

43-3704 Contents Introduction Information FCC Statement Surge Protection Important Safety Instructions Read this Before Installation Important Caller ID Information Installation Selecting a Location On a Desk Top On a Wall Plate or Wall Base downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery Pack Installation To attach the beltclip Installing a BeltclipUsing a Headset To remove the beltclip Animation Displays Example of the standby mode displayDisplay and Icons Talk mode Soft KEY Function Default Settings Main Menu Options Using the Interface Setting Menu OptionsDirectLink Mode Using DirectLink Mode Room Monitor Handset SetupUsing Room Monitor Confirmation tone, and DirectLink Selecting a Ringer Tone Selecting a Ringer VolumePress the OK soft key. You will hear a confirmation tone Distinctive Ringer Setup Setting the True Banner Setting the AutoTalkSetting the Anykey Answer Setting the Key Touch Tone Selecting a Language Setting the Animation Screen Setting Room Monitor Setting the Ring Time Answering System SetupSetting a PIN Code Setting the Record Time Turning the message alert tone off from a remote location Setting the Language of your Answering SystemTurning the message alert tone off by pressing any key Setting Day and Time Global SetupSetting the Call Screen Setting Cidcw Caller ID on Call Waiting Setting the Area Code Setting the Dial Mode DE-REGISTER the Handset Using Your PhoneFrom the handset Making a Call From the Handset Speakerphone Receiving a Call Call Waiting Switching to the Handset Speakerphone During a CallHanging UP Placing a Call on Hold Deleting a Redial Record Storing a Redial Record Adjusting the Handset Earpiece and Speaker Volume Do not Disturb DND Mute Microphone Tone Dialing Switch OverPrivacy Mode Travelling OUT-OF-RANGE Conferencing with 2 outside lines Joining a Conference CallConferencing with one outside line Conferencing Flash and Call Waiting Find Handset Phonebook Storing Phone Numbers NAMES, Distinctive Rings Speed Dial Steps for Entering Names and Special Characters Speed Dial appears. Press Viewing the Phonebook If you make a mistake while entering a name To finish the viewing operation, press Making Calls Using the PhonebookSpeed Dialing To hang up press END Editing or Erasing a Data Editing the Stored Data Copying Phonebook Locations Deleting the Stored Data Testing Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call Waiting Viewing the Caller ID List Deleting all Caller ID names/ numbers Using the Caller ID Message ListDeleting Information from the Caller ID List Calling a party from the Caller ID list Storing Caller ID messages in the Phonebook Long Distance calls and Area Code Setting/CancellationViewing the Caller ID List on Call Waiting Deluxe Features Register the Handset to the Base Expanding Your PhoneDual Handset Expandability DirectLink call Using the Directlink ModeINTERCOM/CALL Transfer Feature From handset to handset Call Transfer FeatureIntercom Expanding Your Phone Features Integrated Answering Device Pre-recorded message Setting your outgoing message GreetingSetting UP Your Answering System Ô Recording a personal outgoing message Greeting Deleting an outgoing message Adjusting the Speaker Volume LevelChoosing between the two outgoing messages LED stops flashing when all new messages are played back Answering System SettingsSetting the Time REPEAT/SELECT until you hear the correct hour setting Setting a PIN code Setting the ring time Selecting the message record time Press CLOCK/MENU three times Press SET Confirmation tone sounds, the system Announce only featureSetting the message alert Selecting the language From the base Setting the call screenScreening a call To screen an incoming call, do the steps as follows Playing your messages Using Your Answering SystemTo cancel the call screen, press END From the handset Repeating a message To maintain maximum record time, delete the old messages. Ô Skipping a messageDeleting a message System returns to standby Voice memoRecording a conversation Remote access away from home Remote Operation Function Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation Ô Troubleshooting Symptom Suggestion Keep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas