Setting the Dial Mode | Radio Shack 43-3704 guide

2.Press CID/VOL/ or REDIAL/P/ to select Line1 or Line2, and then press the OK soft key.

3.Press the number keypad (0-9) to enter a 3-digit area code.

4.Press the OK soft key. You will hear a confirmation tone.

Setting the Dial Mode

Sets the dial mode to tone or pulse. Most phone systems use tone dialing; the default setting is tone dialing. Set the dialing mode to match the dialing system used by your local phone service.

•If you are not sure of your dialing system, set the unit to tone dialing. Make a trial call. If the call connects, leave the setting as is; otherwise set the unit to pulse dialing.

•If your phone system requires pulse dialing and you need to send DTMF tones in certain situations during a call, you may switch over to tone dialing (refer to “Tone Dialing Switch Over” on page 35).

1.Press the MENU soft key. Select the Global Setup menu, and then the Dial Mode submenu.

2.Press CID/VOL/ or REDIAL/P/ to select Line1 or Line2, and then press the OK soft key.

3.Press CID/VOL/ or REDIAL/P/ to select Tone or Pulse (the initial setting is Tone).

4.Press the OK soft key. You will hear a confirmation tone.

Setting Menu Options

29

Image 29

Radio Shack 43-3704 owner manual Setting the Dial Mode

Contents

43-3704 Contents Introduction FCC Statement Information Surge Protection Important Safety Instructions Important Caller ID Information Read this Before Installation Selecting a Location Installation On a Wall Plate or Wall On a Desk Top Base downward to secure it CONNECTING/CHARGING the Battery Pack Recharging the Battery Pack Installation Using a Headset Installing a BeltclipTo attach the beltclip To remove the beltclip Animation Displays Example of the standby mode displayDisplay and Icons Soft KEY Function Talk mode Main Menu Options Default Settings DirectLink Mode Setting Menu OptionsUsing the Interface Using DirectLink Mode Using Room Monitor Handset SetupRoom Monitor Confirmation tone, and DirectLink Selecting a Ringer Tone Selecting a Ringer VolumePress the OK soft key. You will hear a confirmation tone Distinctive Ringer Setup Setting the True Banner Setting the AutoTalkSetting the Anykey Answer Selecting a Language Setting the Key Touch Tone Setting Room Monitor Setting the Animation Screen Setting the Ring Time Answering System SetupSetting a PIN Code Setting the Record Time Turning the message alert tone off from a remote location Setting the Language of your Answering SystemTurning the message alert tone off by pressing any key Setting Day and Time Global SetupSetting the Call Screen Setting the Area Code Setting Cidcw Caller ID on Call Waiting Setting the Dial Mode From the handset Using Your PhoneDE-REGISTER the Handset Making a Call Receiving a Call From the Handset Speakerphone Hanging UP Switching to the Handset Speakerphone During a CallCall Waiting Placing a Call on Hold Storing a Redial Record Deleting a Redial Record Do not Disturb DND Adjusting the Handset Earpiece and Speaker Volume Privacy Mode Tone Dialing Switch OverMute Microphone Travelling OUT-OF-RANGE Conferencing with one outside line Joining a Conference CallConferencing with 2 outside lines Conferencing Find Handset Flash and Call Waiting Storing Phone Numbers NAMES, Distinctive Rings Speed Dial Phonebook Speed Dial appears. Press Steps for Entering Names and Special Characters If you make a mistake while entering a name Viewing the Phonebook Speed Dialing Making Calls Using the PhonebookTo finish the viewing operation, press To hang up press END Editing the Stored Data Editing or Erasing a Data Deleting the Stored Data Copying Phonebook Locations Testing Stored Emergency Numbers Caller ID and Cidcw Caller ID on Call Waiting Caller ID Viewing the Caller ID List Deleting Information from the Caller ID List Using the Caller ID Message ListDeleting all Caller ID names/ numbers Calling a party from the Caller ID list Storing Caller ID messages in the Phonebook Long Distance calls and Area Code Setting/CancellationViewing the Caller ID List on Call Waiting Deluxe Features Register the Handset to the Base Expanding Your PhoneDual Handset Expandability DirectLink call Using the Directlink ModeINTERCOM/CALL Transfer Feature From handset to handset Call Transfer FeatureIntercom Expanding Your Phone Integrated Answering Device Features Setting UP Your Answering System Ô Setting your outgoing message GreetingPre-recorded message Recording a personal outgoing message Greeting Deleting an outgoing message Adjusting the Speaker Volume LevelChoosing between the two outgoing messages Setting the Time Answering System SettingsLED stops flashing when all new messages are played back REPEAT/SELECT until you hear the correct hour setting Setting the ring time Setting a PIN code Press CLOCK/MENU three times Selecting the message record time Press SET Confirmation tone sounds, the system Announce only featureSetting the message alert Selecting the language Screening a call Setting the call screenFrom the base To screen an incoming call, do the steps as follows To cancel the call screen, press END Using Your Answering SystemPlaying your messages From the handset Repeating a message To maintain maximum record time, delete the old messages. Ô Skipping a messageDeleting a message System returns to standby Voice memoRecording a conversation Remote Operation Remote access away from home Function Remote access with the handset ∅/4 Deleting a Message Stop Operation Ô Remote Key Function Symptom Suggestion Troubleshooting Keep the handset away from microwave ovens Care Service and RepairPage Memo Fort Worth, Texas RadioShack Corporation