Setting a PIN code, Setting the ring time | Radio Shack 43-3704

The Integrated Answering Device

Ô NOTES Ô

•To scroll through the menu options, repeatedly press CLOCK/MENU on the base in standby mode. The system returns to standby after the last menu option.

•When you have completed the setting, press !PLAY/"STOP to exit the menu mode, or CLOCK/MENU to move to the next menu option.

8.Press SKIP/SELECT or

REPEAT/SELECT until you hear the correct AM or PM setting.

The message counter displays A or P.

9.Press SET to select the AM/PM setting. A confirmation tone sounds, the day and time you set are announced for your review.

Setting a PIN code

To play your messages from a remote location, you will need to enter a two-digit Personal Identification Number (PIN) code. To select a PIN code, perform the following steps: Ô

1.Press L1 ANSWER or L2 ANSWER.

2.Press CLOCK/MENU once. The current PIN code appears on the base and it is announced.

3.Press SKIP/SELECT or

REPEAT/SELECT until the desired number appears. Press and hold

SKIP/SELECT or REPEAT/SELECT

to quickly scroll through the numbers on the display.

4.Press SET to select the PIN code.

A confirmation tone sounds, the system announces the new PIN code.

Setting the ring time

The ring time setting allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. Setting “TS” (Toll Saver), the answering system picks up after two rings if you have new messages, and after four rings if there are none. This way, if you make a long distance

58

Image 58

Radio Shack 43-3704 owner manual Setting a PIN code, Setting the ring time

Contents

43-3704 Contents Introduction Information FCC Statement Surge Protection Important Safety Instructions Read this Before Installation Important Caller ID Information Installation Selecting a Location On a Desk Top On a Wall Plate or Wall Base downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery Pack Installation To attach the beltclip Installing a BeltclipUsing a Headset To remove the beltclip Display and Icons Example of the standby mode displayAnimation Displays Talk mode Soft KEY Function Default Settings Main Menu Options Using the Interface Setting Menu OptionsDirectLink Mode Using DirectLink Mode Room Monitor Handset SetupUsing Room Monitor Confirmation tone, and DirectLink Press the OK soft key. You will hear a confirmation tone Selecting a Ringer VolumeSelecting a Ringer Tone Distinctive Ringer Setup Setting the Anykey Answer Setting the AutoTalkSetting the True Banner Setting the Key Touch Tone Selecting a Language Setting the Animation Screen Setting Room Monitor Setting a PIN Code Answering System SetupSetting the Ring Time Setting the Record Time Turning the message alert tone off by pressing any key Setting the Language of your Answering SystemTurning the message alert tone off from a remote location Setting the Call Screen Global SetupSetting Day and Time Setting Cidcw Caller ID on Call Waiting Setting the Area Code Setting the Dial Mode DE-REGISTER the Handset Using Your PhoneFrom the handset Making a Call From the Handset Speakerphone Receiving a Call Call Waiting Switching to the Handset Speakerphone During a CallHanging UP Placing a Call on Hold Deleting a Redial Record Storing a Redial Record Adjusting the Handset Earpiece and Speaker Volume Do not Disturb DND Mute Microphone Tone Dialing Switch OverPrivacy Mode Travelling OUT-OF-RANGE Conferencing with 2 outside lines Joining a Conference CallConferencing with one outside line Conferencing Flash and Call Waiting Find Handset Phonebook Storing Phone Numbers NAMES, Distinctive Rings Speed Dial Steps for Entering Names and Special Characters Speed Dial appears. Press Viewing the Phonebook If you make a mistake while entering a name To finish the viewing operation, press Making Calls Using the PhonebookSpeed Dialing To hang up press END Editing or Erasing a Data Editing the Stored Data Copying Phonebook Locations Deleting the Stored Data Testing Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call Waiting Viewing the Caller ID List Deleting all Caller ID names/ numbers Using the Caller ID Message ListDeleting Information from the Caller ID List Calling a party from the Caller ID list Viewing the Caller ID List on Long Distance calls and Area Code Setting/CancellationStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Dual Handset Expandability Expanding Your PhoneRegister the Handset to the Base INTERCOM/CALL Transfer Feature Using the Directlink ModeDirectLink call Intercom Call Transfer FeatureFrom handset to handset Expanding Your Phone Features Integrated Answering Device Pre-recorded message Setting your outgoing message GreetingSetting UP Your Answering System Ô Recording a personal outgoing message Greeting Choosing between the two outgoing messages Adjusting the Speaker Volume LevelDeleting an outgoing message LED stops flashing when all new messages are played back Answering System SettingsSetting the Time REPEAT/SELECT until you hear the correct hour setting Setting a PIN code Setting the ring time Selecting the message record time Press CLOCK/MENU three times Setting the message alert Announce only featurePress SET Confirmation tone sounds, the system Selecting the language From the base Setting the call screenScreening a call To screen an incoming call, do the steps as follows Playing your messages Using Your Answering SystemTo cancel the call screen, press END From the handset Repeating a message Deleting a message Skipping a messageTo maintain maximum record time, delete the old messages. Ô Recording a conversation Voice memoSystem returns to standby Remote access away from home Remote Operation Function Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation Ô Troubleshooting Symptom Suggestion Keep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas