Manuals / Radio Shack / Communications / Cordless Telephone

Radio Shack 43-3704 owner manual Answering System Setup, Setting a PIN Code, Setting the Ring Time

Models: 43-3704

1 76

Download 76 pages 18.3 Kb

Page 24

Setting Menu Options

Answering System Setup

This main menu option allows you to set up the built in answering device.

The following submenu options must be set separately for each line (line1 and line2).

Setting a PIN Code

Security code selects a two-digit Personal Identification Number (PIN) code. A PIN code is required to play your messages from a remote location.

1.Press the MENU soft key. Select the Answ. Setup menu.

2.Press CID/VOL/ or REDIAL/P/ to select Line1 or Line2, and then the OK soft key.

3.Press CID/VOL/ or REDIAL/P/ to select Security Code submenu, and then the OK soft key.

4.Enter a two-digit PIN code (01-99) using the number keypad (0-9).

5.Press the OK soft key. You will hear a confirmation tone.

Setting the Ring Time

Ring Time allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. If you enable the Toll Saver (TS), the answering system picks up after two rings if you have new messages and after four rings if there are none.

1.Press the MENU soft key. Select the Answ. Setup menu.

2.Press CID/VOL/ or REDIAL/P/ to select Line1 or Line2, and then the OK soft key.

24

Image 24

Radio Shack 43-3704 owner manual Answering System Setup, Setting a PIN Code, Setting the Ring Time

Contents

43-3704 Contents Introduction Information FCC StatementSurge Protection Important Safety Instructions Read this Before Installation Important Caller ID InformationInstallation Selecting a LocationOn a Desk Top On a Wall Plate or WallBase downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery PackInstallation Installing a Beltclip Using a HeadsetTo attach the beltclip To remove the beltclipExample of the standby mode display Display and IconsAnimation Displays Talk mode Soft KEY FunctionDefault Settings Main Menu OptionsSetting Menu Options DirectLink ModeUsing the Interface Using DirectLink ModeHandset Setup Using Room MonitorRoom Monitor Confirmation tone, and DirectLinkSelecting a Ringer Volume Press the OK soft key. You will hear a confirmation toneSelecting a Ringer Tone Distinctive Ringer Setup Setting the AutoTalk Setting the Anykey AnswerSetting the True Banner Setting the Key Touch Tone Selecting a LanguageSetting the Animation Screen Setting Room MonitorAnswering System Setup Setting a PIN CodeSetting the Ring Time Setting the Record Time Setting the Language of your Answering System Turning the message alert tone off by pressing any keyTurning the message alert tone off from a remote location Global Setup Setting the Call ScreenSetting Day and Time Setting Cidcw Caller ID on Call Waiting Setting the Area CodeSetting the Dial Mode Using Your Phone From the handsetDE-REGISTER the Handset Making a CallFrom the Handset Speakerphone Receiving a CallSwitching to the Handset Speakerphone During a Call Hanging UPCall Waiting Placing a Call on HoldDeleting a Redial Record Storing a Redial RecordAdjusting the Handset Earpiece and Speaker Volume Do not Disturb DNDTone Dialing Switch Over Privacy ModeMute Microphone Travelling OUT-OF-RANGEJoining a Conference Call Conferencing with one outside lineConferencing with 2 outside lines ConferencingFlash and Call Waiting Find HandsetPhonebook Storing Phone Numbers NAMES, Distinctive Rings Speed DialSteps for Entering Names and Special Characters Speed Dial appears. PressViewing the Phonebook If you make a mistake while entering a nameMaking Calls Using the Phonebook Speed DialingTo finish the viewing operation, press To hang up press ENDEditing or Erasing a Data Editing the Stored DataCopying Phonebook Locations Deleting the Stored DataTesting Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call WaitingViewing the Caller ID List Using the Caller ID Message List Deleting Information from the Caller ID ListDeleting all Caller ID names/ numbers Calling a party from the Caller ID listLong Distance calls and Area Code Setting/Cancellation Viewing the Caller ID List onStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Expanding Your Phone Dual Handset ExpandabilityRegister the Handset to the Base Using the Directlink Mode INTERCOM/CALL Transfer FeatureDirectLink call Call Transfer Feature IntercomFrom handset to handset Expanding Your Phone Features Integrated Answering DeviceSetting your outgoing message Greeting Setting UP Your Answering System ÔPre-recorded message Recording a personal outgoing message GreetingAdjusting the Speaker Volume Level Choosing between the two outgoing messagesDeleting an outgoing message Answering System Settings Setting the TimeLED stops flashing when all new messages are played back REPEAT/SELECT until you hear the correct hour settingSetting a PIN code Setting the ring timeSelecting the message record time Press CLOCK/MENU three timesAnnounce only feature Setting the message alertPress SET Confirmation tone sounds, the system Selecting the language Setting the call screen Screening a callFrom the base To screen an incoming call, do the steps as followsUsing Your Answering System To cancel the call screen, press ENDPlaying your messages From the handsetRepeating a message Skipping a message Deleting a messageTo maintain maximum record time, delete the old messages. Ô Voice memo Recording a conversationSystem returns to standby Remote access away from home Remote OperationFunction Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation ÔTroubleshooting Symptom SuggestionKeep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas