Installation | Radio Shack 43-3704 specification

Installation

o WARNING o Dispose of the old battery pack promptly and properly. Do not burn or bury it. There is a risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

the display. Otherwise, the battery pack loses its ability to fully recharge.

•Using a damp cloth, clean the charging contacts on the handset about once a month.

•If you are not going to use your phone for an extended period, disconnect the battery pack. This increases the battery pack’s usable life.

•The supplied battery pack should last for about a year. If the battery pack does not hold a charge for more than 2 hours after an overnight charge, replace it with a new 3.6-volt, 800 mAh battery pack with a connector that fits the socket in the battery compartment. You can order a replacement battery pack through RadioShack. Install the new battery pack and charge it for about 15–20 hours.o

12

Image 12

Radio Shack 43-3704 owner manual Installation

Contents

43-3704 Contents Introduction Information FCC Statement Surge Protection Important Safety Instructions Read this Before Installation Important Caller ID Information Installation Selecting a Location On a Desk Top On a Wall Plate or Wall Base downward to secure it Recharging the Battery Pack CONNECTING/CHARGING the Battery Pack Installation Installing a Beltclip Using a HeadsetTo attach the beltclip To remove the beltclip Example of the standby mode display Display and IconsAnimation Displays Talk mode Soft KEY Function Default Settings Main Menu Options Setting Menu Options DirectLink ModeUsing the Interface Using DirectLink Mode Handset Setup Using Room MonitorRoom Monitor Confirmation tone, and DirectLink Selecting a Ringer Volume Press the OK soft key. You will hear a confirmation toneSelecting a Ringer Tone Distinctive Ringer Setup Setting the AutoTalk Setting the Anykey AnswerSetting the True Banner Setting the Key Touch Tone Selecting a Language Setting the Animation Screen Setting Room Monitor Answering System Setup Setting a PIN CodeSetting the Ring Time Setting the Record Time Setting the Language of your Answering System Turning the message alert tone off by pressing any keyTurning the message alert tone off from a remote location Global Setup Setting the Call ScreenSetting Day and Time Setting Cidcw Caller ID on Call Waiting Setting the Area Code Setting the Dial Mode Using Your Phone From the handsetDE-REGISTER the Handset Making a Call From the Handset Speakerphone Receiving a Call Switching to the Handset Speakerphone During a Call Hanging UPCall Waiting Placing a Call on Hold Deleting a Redial Record Storing a Redial Record Adjusting the Handset Earpiece and Speaker Volume Do not Disturb DND Tone Dialing Switch Over Privacy ModeMute Microphone Travelling OUT-OF-RANGE Joining a Conference Call Conferencing with one outside lineConferencing with 2 outside lines Conferencing Flash and Call Waiting Find Handset Phonebook Storing Phone Numbers NAMES, Distinctive Rings Speed Dial Steps for Entering Names and Special Characters Speed Dial appears. Press Viewing the Phonebook If you make a mistake while entering a name Making Calls Using the Phonebook Speed DialingTo finish the viewing operation, press To hang up press END Editing or Erasing a Data Editing the Stored Data Copying Phonebook Locations Deleting the Stored Data Testing Stored Emergency Numbers Caller ID Caller ID and Cidcw Caller ID on Call Waiting Viewing the Caller ID List Using the Caller ID Message List Deleting Information from the Caller ID ListDeleting all Caller ID names/ numbers Calling a party from the Caller ID list Long Distance calls and Area Code Setting/Cancellation Viewing the Caller ID List onStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Expanding Your Phone Dual Handset ExpandabilityRegister the Handset to the Base Using the Directlink Mode INTERCOM/CALL Transfer FeatureDirectLink call Call Transfer Feature IntercomFrom handset to handset Expanding Your Phone Features Integrated Answering Device Setting your outgoing message Greeting Setting UP Your Answering System ÔPre-recorded message Recording a personal outgoing message Greeting Adjusting the Speaker Volume Level Choosing between the two outgoing messagesDeleting an outgoing message Answering System Settings Setting the TimeLED stops flashing when all new messages are played back REPEAT/SELECT until you hear the correct hour setting Setting a PIN code Setting the ring time Selecting the message record time Press CLOCK/MENU three times Announce only feature Setting the message alertPress SET Confirmation tone sounds, the system Selecting the language Setting the call screen Screening a callFrom the base To screen an incoming call, do the steps as follows Using Your Answering System To cancel the call screen, press ENDPlaying your messages From the handset Repeating a message Skipping a message Deleting a messageTo maintain maximum record time, delete the old messages. Ô Voice memo Recording a conversationSystem returns to standby Remote access away from home Remote Operation Function Remote access with the handset Remote Key Function ∅/4 Deleting a Message Stop Operation Ô Troubleshooting Symptom Suggestion Keep the handset away from microwave ovens Service and Repair CarePage Memo RadioShack Corporation Fort Worth, Texas