Speed Dial appears. Press | Radio Shack 43-3704 guide

5.Press the number keypad to enter the phone number (up to 20 digits), press the OK soft key to store the number. Ô

6.Distinctive Ring appears. Press

CID/VOL/ or REDIAL/P/ to move the pointer to one of the Distinctive Ring options, and then press the OK soft key.

Ô

7.Speed Dial appears. Press

CID/VOL/ or REDIAL/P/ to move the pointer to select the Speed dial location (ten locations: SPD1-SPD0).Ô

8.Press the OK soft key. You will hear a confirmation tone, and Done! appears in the display.

STEPS FOR ENTERING NAMES AND SPECIAL CHARACTERS

Refer to the letters on the number keys to select the desired characters. With each press of a number key (0-9), the displayed character appears in the following order:

upper case letters first, lower case letters next and finally the number corresponding to the key. Ô

Ô NOTES Ô

•The pause key counts as one digit. Pressing REDIAL/P/ more than once increases the length of the pause between numbers. Each pause represents a two second delay.

•If you choose not to store a “Distinctive Ring”, simply select the “No Selectn” option.

•Selecting a speed dial location where a number is already stored, releases the old number’s speed dial setting. The new number will be stored in the speed dial location.

•If you choose not to store the name/number as a Speed Dial, simply select the “No Selectn” option.

•If the next character uses the same number key, you must press #/> to move the cursor over. Otherwise the next time you press the number key, it changes the character that was previously set.

Phonebook

39

Image 39

Radio Shack 43-3704 owner manual Steps for Entering Names and Special Characters, Speed Dial appears. Press

Contents

43-3704 Contents Introduction FCC Statement Information Surge Protection Important Safety Instructions Important Caller ID Information Read this Before Installation Selecting a Location Installation On a Wall Plate or Wall On a Desk Top Base downward to secure it CONNECTING/CHARGING the Battery Pack Recharging the Battery Pack Installation To remove the beltclip Installing a BeltclipUsing a Headset To attach the beltclip Example of the standby mode display Display and IconsAnimation Displays Soft KEY Function Talk mode Main Menu Options Default Settings Using DirectLink Mode Setting Menu OptionsDirectLink Mode Using the Interface Confirmation tone, and DirectLink Handset SetupUsing Room Monitor Room Monitor Selecting a Ringer Volume Press the OK soft key. You will hear a confirmation toneSelecting a Ringer Tone Distinctive Ringer Setup Setting the AutoTalk Setting the Anykey AnswerSetting the True Banner Selecting a Language Setting the Key Touch Tone Setting Room Monitor Setting the Animation Screen Answering System Setup Setting a PIN CodeSetting the Ring Time Setting the Record Time Setting the Language of your Answering System Turning the message alert tone off by pressing any keyTurning the message alert tone off from a remote location Global Setup Setting the Call ScreenSetting Day and Time Setting the Area Code Setting Cidcw Caller ID on Call Waiting Setting the Dial Mode Making a Call Using Your PhoneFrom the handset DE-REGISTER the Handset Receiving a Call From the Handset Speakerphone Placing a Call on Hold Switching to the Handset Speakerphone During a CallHanging UP Call Waiting Storing a Redial Record Deleting a Redial Record Do not Disturb DND Adjusting the Handset Earpiece and Speaker Volume Travelling OUT-OF-RANGE Tone Dialing Switch OverPrivacy Mode Mute Microphone Conferencing Joining a Conference CallConferencing with one outside line Conferencing with 2 outside lines Find Handset Flash and Call Waiting Storing Phone Numbers NAMES, Distinctive Rings Speed Dial Phonebook Speed Dial appears. Press Steps for Entering Names and Special Characters If you make a mistake while entering a name Viewing the Phonebook To hang up press END Making Calls Using the PhonebookSpeed Dialing To finish the viewing operation, press Editing the Stored Data Editing or Erasing a Data Deleting the Stored Data Copying Phonebook Locations Testing Stored Emergency Numbers Caller ID and Cidcw Caller ID on Call Waiting Caller ID Viewing the Caller ID List Calling a party from the Caller ID list Using the Caller ID Message ListDeleting Information from the Caller ID List Deleting all Caller ID names/ numbers Long Distance calls and Area Code Setting/Cancellation Viewing the Caller ID List onStoring Caller ID messages in the Phonebook Call Waiting Deluxe Features Expanding Your Phone Dual Handset ExpandabilityRegister the Handset to the Base Using the Directlink Mode INTERCOM/CALL Transfer FeatureDirectLink call Call Transfer Feature IntercomFrom handset to handset Expanding Your Phone Integrated Answering Device Features Recording a personal outgoing message Greeting Setting your outgoing message GreetingSetting UP Your Answering System Ô Pre-recorded message Adjusting the Speaker Volume Level Choosing between the two outgoing messagesDeleting an outgoing message REPEAT/SELECT until you hear the correct hour setting Answering System SettingsSetting the Time LED stops flashing when all new messages are played back Setting the ring time Setting a PIN code Press CLOCK/MENU three times Selecting the message record time Announce only feature Setting the message alertPress SET Confirmation tone sounds, the system Selecting the language To screen an incoming call, do the steps as follows Setting the call screenScreening a call From the base From the handset Using Your Answering SystemTo cancel the call screen, press END Playing your messages Repeating a message Skipping a message Deleting a messageTo maintain maximum record time, delete the old messages. Ô Voice memo Recording a conversationSystem returns to standby Remote Operation Remote access away from home Function Remote access with the handset ∅/4 Deleting a Message Stop Operation Ô Remote Key Function Symptom Suggestion Troubleshooting Keep the handset away from microwave ovens Care Service and RepairPage Memo Fort Worth, Texas RadioShack Corporation