Recharging the Battery Pack | Radio Shack 43-3704 instruction

CONNECTING/CHARGING THE BATTERY PACK

The phone comes with a rechargeable nickel-metal hydride (Ni-MH) battery pack in the handset, but not connected. Before using your phone, you must connect the battery pack, then charge it for about 15–20 hours.

1.Press down and slide off the battery compartment cover.

2.Lift the battery pack out of the compartment.

3.Plug the battery pack’s connector into the socket in the compartment (the connector fits only one way), then place the battery pack in the compartment.

4.Replace the cover.

To charge the battery pack, place the handset on the base. The CHARGE indicator on the base lights.

Recharge the battery pack when

Low Battery flashes on the display.

If you have trouble replacing the battery pack, take the phone to your local RadioShack for assistance.

Recharging the Battery Pack

•If the battery pack becomes weak during a call, Low Battery flashes. When this happens, you cannot make a call until you recharge the battery pack.!

•If the display is blank and the phone does not work, recharge the battery pack. (The battery power might be too low to light the display.)

•About once a month, fully discharge the battery by keeping the handset off the base until Low Battery flashes on

! IMPORTANT !

Be sure the battery pack is properly connected before you try to charge it. The CHARGE indicator lights when the handset is on the base, even if the battery pack is not connected.

Installation

11

Image 11

Radio Shack 43-3704 owner manual Recharging the Battery Pack, CONNECTING/CHARGING the Battery Pack

Contents

43-3704 Contents Introduction FCC Statement Information Surge Protection Important Safety Instructions Important Caller ID Information Read this Before Installation Selecting a Location Installation On a Wall Plate or Wall On a Desk Top Base downward to secure it CONNECTING/CHARGING the Battery Pack Recharging the Battery Pack Installation To remove the beltclip Installing a BeltclipUsing a Headset To attach the beltclip Animation Displays Example of the standby mode displayDisplay and Icons Soft KEY Function Talk mode Main Menu Options Default Settings Using DirectLink Mode Setting Menu OptionsDirectLink Mode Using the Interface Confirmation tone, and DirectLink Handset SetupUsing Room Monitor Room Monitor Selecting a Ringer Tone Selecting a Ringer VolumePress the OK soft key. You will hear a confirmation tone Distinctive Ringer Setup Setting the True Banner Setting the AutoTalkSetting the Anykey Answer Selecting a Language Setting the Key Touch Tone Setting Room Monitor Setting the Animation Screen Setting the Ring Time Answering System SetupSetting a PIN Code Setting the Record Time Turning the message alert tone off from a remote location Setting the Language of your Answering SystemTurning the message alert tone off by pressing any key Setting Day and Time Global SetupSetting the Call Screen Setting the Area Code Setting Cidcw Caller ID on Call Waiting Setting the Dial Mode Making a Call Using Your PhoneFrom the handset DE-REGISTER the Handset Receiving a Call From the Handset Speakerphone Placing a Call on Hold Switching to the Handset Speakerphone During a CallHanging UP Call Waiting Storing a Redial Record Deleting a Redial Record Do not Disturb DND Adjusting the Handset Earpiece and Speaker Volume Travelling OUT-OF-RANGE Tone Dialing Switch OverPrivacy Mode Mute Microphone Conferencing Joining a Conference CallConferencing with one outside line Conferencing with 2 outside lines Find Handset Flash and Call Waiting Storing Phone Numbers NAMES, Distinctive Rings Speed Dial Phonebook Speed Dial appears. Press Steps for Entering Names and Special Characters If you make a mistake while entering a name Viewing the Phonebook To hang up press END Making Calls Using the PhonebookSpeed Dialing To finish the viewing operation, press Editing the Stored Data Editing or Erasing a Data Deleting the Stored Data Copying Phonebook Locations Testing Stored Emergency Numbers Caller ID and Cidcw Caller ID on Call Waiting Caller ID Viewing the Caller ID List Calling a party from the Caller ID list Using the Caller ID Message ListDeleting Information from the Caller ID List Deleting all Caller ID names/ numbers Storing Caller ID messages in the Phonebook Long Distance calls and Area Code Setting/CancellationViewing the Caller ID List on Call Waiting Deluxe Features Register the Handset to the Base Expanding Your PhoneDual Handset Expandability DirectLink call Using the Directlink ModeINTERCOM/CALL Transfer Feature From handset to handset Call Transfer FeatureIntercom Expanding Your Phone Integrated Answering Device Features Recording a personal outgoing message Greeting Setting your outgoing message GreetingSetting UP Your Answering System Ô Pre-recorded message Deleting an outgoing message Adjusting the Speaker Volume LevelChoosing between the two outgoing messages REPEAT/SELECT until you hear the correct hour setting Answering System SettingsSetting the Time LED stops flashing when all new messages are played back Setting the ring time Setting a PIN code Press CLOCK/MENU three times Selecting the message record time Press SET Confirmation tone sounds, the system Announce only featureSetting the message alert Selecting the language To screen an incoming call, do the steps as follows Setting the call screenScreening a call From the base From the handset Using Your Answering SystemTo cancel the call screen, press END Playing your messages Repeating a message To maintain maximum record time, delete the old messages. Ô Skipping a messageDeleting a message System returns to standby Voice memoRecording a conversation Remote Operation Remote access away from home Function Remote access with the handset ∅/4 Deleting a Message Stop Operation Ô Remote Key Function Symptom Suggestion Troubleshooting Keep the handset away from microwave ovens Care Service and RepairPage Memo Fort Worth, Texas RadioShack Corporation