Revox Recontrol M207 Appendix B

71

Appendix B

Optional Accessories

Re:connect USB cable

USB Cable Transmit Wire

The Re:connect USB cable enables transmission of system setup

between a PC and the Re:control M207. With Transmit Wire the

Re:control M207 also can duplicate the user setup data for one to

another.

RemoteComm: With the “RemoteComm” software enables user to

customize the remote control, create macros and timers.

Upgrade Tools: With the “Upgrade Tools” enables user to upgrade MCU

program and Pre-Programmed Code. (Please refer to 5.3 Upgrade

VMCU Firmware and VMCF Pre-programmed Codes P.65)

Duplicate: By connecting a “Transmit Wire” between two Re:control

M207s, you can duplicate settings and functions from one Re:control

M207 to another.

Free “RemoteComm” & “Upgrade Tools” software can be downloaded

from www.revox.de for further customization.

Docking Station

Docking Station

Optional docking station can recharge the batteries easily. The package is

including Ni-MH AAA rechargeable batteries and desktop charger circuit.

Contents

Main Preface i Preface About this manual Copyright Page Table of Contents Page Chapter 1 Introducing Re:control M207 1.1 Re:control M207 Features 1.2 Unpacking the Re:control M207 1.3 Installing Battery 1.3.1 Precautions for using battery 1.4 Turning the touch screen on 1.5 Identifying Components 1.5.1 The front side of the re:control M207 1.5.2 The rear side of the Re:control M207 1.5.3 Direct Access Buttons (Rubber Buttons) 1.5.4 LCD Touch Screen 1.5.5 Precautions of using touch screen 1.5.6 Touch screen keys Introducing the frequently used LCD Layout as followed: y Device Layout y Main Menu y Basic Information Layout y Timer Macro Layout y Setup Menu Layout Timer Macro Setup Mode Chapter 2 Quick Start 2.1 Re-calibrate the screen 2.2 Date / Time setting 2.3 Device setting Page Chapter 3 How to Set Your Re:control M207 3.1 Add a Device 3.1.1 Create a new device Page 3.1.2 Load the codes for the newly-added device A. Pre-code Page Page = 3.2 Add a Soft Key b. 3.3 Add a Text 3.4 Re-label a Device, Key or Text Page 3.5 Re-size a Device, Key or Text Page 3.6 Delete a Device, Key or Text 3.7 Pre-code Page Page 3.8 Learning = 3.9 Learn a Cycle key Page 3.10 Delete Device/Key codes 3.11 Create a Macro 3.11.1 Macro b. Re:control M207 Users Manual An Example to Add a Macro The basic devices in operation: The commands for the Macro key. The correlation table could be shown as below: 3.11.2 Timer Macro A. Create a Timer Macro Page B. Delete Your Timer Macro C. Re-label Your Timer Macro D. View Your Timer Macro 3.12 Create Your Favorite Channels 3.12.1 Add the favorite channel keys 3.12.2 Set these Macros as your favorite channels Chapter 4 Menus 4.1 Setting Page LCD Off Light Sensitivity Light Period Motion Welcome Page Calibrate 4.2 Key Layout 4.3 Code Setting 4.4 Timer Macro 4.5 Duplicate Duplicate Page 4.6 Calibrate Chapter 5 Install USB Cable and Software 5.1 Install Re:connect USB cable 5.1.1 Install the Driver Page 5.2 Install Upgrade Tools Page 5.3 Upgrade VMCU Firmware and VMCF Pre-programmed Codes Page Page Appendix A Features Re:control M207 Users Manual Specifications Appendix B Optional Accessories 72 Appendix C Troubleshooting Tables Problem Solution 73 Problem Solution