Revox Recontrol M207 3.9 Learn a Cycle key

Chapter 3 How to Set Your Re:control M207

39

press the specific key on your original remotes for about 2-3 seconds

until the symbol shows up on LCD.

7. The symbol will show up when the Re:control M207 learns

remote codes successfully. However, the symbol will show up

when the Re:control M207 fails to learn the remote codes. Please

repeat step 5. to learn the remote code if the Re:control M207 fails to

copy it.

8. Please press the button when you finish learning all keys.

learning successfully Learning fail

The preset layout for your device may not match

your original remote completely. Please use

“ Add Key” (Page 26) and “Delete” (Page

33) functions to adjust the layout.

3.9 Learn a Cycle key

Some devices save a circle of commands in one button. For the special

design, the Re:control M207 is equipped the Cycle function. With the

function, you are able to send the circle of commands.

1. Please press the button for 1 second to enter Setup Menu. And

then enter “Code Setting” menu.

2. Please choose the “ Cycle” item and then press the button

to enter the submenu.

Contents

Main Preface i Preface About this manual Copyright Page Table of Contents Page Chapter 1 Introducing Re:control M207 1.1 Re:control M207 Features 1.2 Unpacking the Re:control M207 1.3 Installing Battery 1.3.1 Precautions for using battery 1.4 Turning the touch screen on 1.5 Identifying Components 1.5.1 The front side of the re:control M207 1.5.2 The rear side of the Re:control M207 1.5.3 Direct Access Buttons (Rubber Buttons) 1.5.4 LCD Touch Screen 1.5.5 Precautions of using touch screen 1.5.6 Touch screen keys Introducing the frequently used LCD Layout as followed: y Device Layout y Main Menu y Basic Information Layout y Timer Macro Layout y Setup Menu Layout Timer Macro Setup Mode Chapter 2 Quick Start 2.1 Re-calibrate the screen 2.2 Date / Time setting 2.3 Device setting Page Chapter 3 How to Set Your Re:control M207 3.1 Add a Device 3.1.1 Create a new device Page 3.1.2 Load the codes for the newly-added device A. Pre-code Page Page = 3.2 Add a Soft Key b. 3.3 Add a Text 3.4 Re-label a Device, Key or Text Page 3.5 Re-size a Device, Key or Text Page 3.6 Delete a Device, Key or Text 3.7 Pre-code Page Page 3.8 Learning = 3.9 Learn a Cycle key Page 3.10 Delete Device/Key codes 3.11 Create a Macro 3.11.1 Macro b. Re:control M207 Users Manual An Example to Add a Macro The basic devices in operation: The commands for the Macro key. The correlation table could be shown as below: 3.11.2 Timer Macro A. Create a Timer Macro Page B. Delete Your Timer Macro C. Re-label Your Timer Macro D. View Your Timer Macro 3.12 Create Your Favorite Channels 3.12.1 Add the favorite channel keys 3.12.2 Set these Macros as your favorite channels Chapter 4 Menus 4.1 Setting Page LCD Off Light Sensitivity Light Period Motion Welcome Page Calibrate 4.2 Key Layout 4.3 Code Setting 4.4 Timer Macro 4.5 Duplicate Duplicate Page 4.6 Calibrate Chapter 5 Install USB Cable and Software 5.1 Install Re:connect USB cable 5.1.1 Install the Driver Page 5.2 Install Upgrade Tools Page 5.3 Upgrade VMCU Firmware and VMCF Pre-programmed Codes Page Page Appendix A Features Re:control M207 Users Manual Specifications Appendix B Optional Accessories 72 Appendix C Troubleshooting Tables Problem Solution 73 Problem Solution