Revox Recontrol M207 2.3 Device setting

Re:control M207 User’s Manual

18

2.3 Device setting

1. Turn on the targeted device for the Re:control M207 to setting the

device.

2. The Re:control M207 will directly get throw the setup mode when

you operate the Re:control M207 at first time. Please tap the

target device key in the Main Menu to enter “Setup device” menu.

(ex. “TV” device)

* Pre-code: load pre-programmed IR code from the factory

default (no guarantee being able to control all brand

devices).

3. Pressing the or buttons to choose “Yes” item and

press button for entering the operation mode.

4. Choose the first letter of targeted device brand (ex. n “S” on

behalf of Sony, Samsung…etc ), and point the Re:control

M207 at the targeted device, and then tap o soft button

to start auto searching.

5. As you see the targeted device has been turned off, please tap

or press any buttons to stop auto searching right away. Tap

or p gently to figure out the correct remote code

(Code number as shown on the top middle position of the

LCD.) till the targeted device has been turned on again. Press

the power key or the hard key to test the codes to confirm the

code. If the codes aren’t correct please continue repeat step

4-5 again to search the proper code for your target device.

6. Finally, press button to load the code and exit.

Contents

Main Preface i Preface About this manual Copyright Page Table of Contents Page Chapter 1 Introducing Re:control M207 1.1 Re:control M207 Features 1.2 Unpacking the Re:control M207 1.3 Installing Battery 1.3.1 Precautions for using battery 1.4 Turning the touch screen on 1.5 Identifying Components 1.5.1 The front side of the re:control M207 1.5.2 The rear side of the Re:control M207 1.5.3 Direct Access Buttons (Rubber Buttons) 1.5.4 LCD Touch Screen 1.5.5 Precautions of using touch screen 1.5.6 Touch screen keys Introducing the frequently used LCD Layout as followed: y Device Layout y Main Menu y Basic Information Layout y Timer Macro Layout y Setup Menu Layout Timer Macro Setup Mode Chapter 2 Quick Start 2.1 Re-calibrate the screen 2.2 Date / Time setting 2.3 Device setting Page Chapter 3 How to Set Your Re:control M207 3.1 Add a Device 3.1.1 Create a new device Page 3.1.2 Load the codes for the newly-added device A. Pre-code Page Page = 3.2 Add a Soft Key b. 3.3 Add a Text 3.4 Re-label a Device, Key or Text Page 3.5 Re-size a Device, Key or Text Page 3.6 Delete a Device, Key or Text 3.7 Pre-code Page Page 3.8 Learning = 3.9 Learn a Cycle key Page 3.10 Delete Device/Key codes 3.11 Create a Macro 3.11.1 Macro b. Re:control M207 Users Manual An Example to Add a Macro The basic devices in operation: The commands for the Macro key. The correlation table could be shown as below: 3.11.2 Timer Macro A. Create a Timer Macro Page B. Delete Your Timer Macro C. Re-label Your Timer Macro D. View Your Timer Macro 3.12 Create Your Favorite Channels 3.12.1 Add the favorite channel keys 3.12.2 Set these Macros as your favorite channels Chapter 4 Menus 4.1 Setting Page LCD Off Light Sensitivity Light Period Motion Welcome Page Calibrate 4.2 Key Layout 4.3 Code Setting 4.4 Timer Macro 4.5 Duplicate Duplicate Page 4.6 Calibrate Chapter 5 Install USB Cable and Software 5.1 Install Re:connect USB cable 5.1.1 Install the Driver Page 5.2 Install Upgrade Tools Page 5.3 Upgrade VMCU Firmware and VMCF Pre-programmed Codes Page Page Appendix A Features Re:control M207 Users Manual Specifications Appendix B Optional Accessories 72 Appendix C Troubleshooting Tables Problem Solution 73 Problem Solution