Revox Recontrol M207 3.2 Add a Soft Key

Re:control M207 User’s Manual

26

4. The symbol will show up when the Re:control M207

learns remote codes successfully. However, the symbol

will show up when the Re:control M207 fails to learn the

remote codes. If the Re:control M207 fails to copy the remote

code please repeat step3.

5. Please press the button when you finish learning all keys.

learning

successfully Learning fail

The preset layout for your device

may not match your original remote

completely. Please use “Add Key”

(Page 26) and “Delete” (Page 33)

functions to adjust the layout.

3.2 Add a Soft Key

With the function, you are able to create a new soft key in your devices.

There are two main stages for you to add a soft key successfully. The

first one is to create a new soft key in your target device. The second

one is to load the specific code for your newly-added soft key.

1. Please press the button for about 3 seconds to enter Setup

Menu. And then enter “Key Layout” menu.

2. Please choose the “ Add Key” item and then you will enter the

submenu.

3. On tapping the soft key, you will see the indication for the function.

After reading the tips, please press the button to go to next

step.

Contents

Main Preface i Preface About this manual Copyright Page Table of Contents Page Chapter 1 Introducing Re:control M207 1.1 Re:control M207 Features 1.2 Unpacking the Re:control M207 1.3 Installing Battery 1.3.1 Precautions for using battery 1.4 Turning the touch screen on 1.5 Identifying Components 1.5.1 The front side of the re:control M207 1.5.2 The rear side of the Re:control M207 1.5.3 Direct Access Buttons (Rubber Buttons) 1.5.4 LCD Touch Screen 1.5.5 Precautions of using touch screen 1.5.6 Touch screen keys Introducing the frequently used LCD Layout as followed: y Device Layout y Main Menu y Basic Information Layout y Timer Macro Layout y Setup Menu Layout Timer Macro Setup Mode Chapter 2 Quick Start 2.1 Re-calibrate the screen 2.2 Date / Time setting 2.3 Device setting Page Chapter 3 How to Set Your Re:control M207 3.1 Add a Device 3.1.1 Create a new device Page 3.1.2 Load the codes for the newly-added device A. Pre-code Page Page = 3.2 Add a Soft Key b. 3.3 Add a Text 3.4 Re-label a Device, Key or Text Page 3.5 Re-size a Device, Key or Text Page 3.6 Delete a Device, Key or Text 3.7 Pre-code Page Page 3.8 Learning = 3.9 Learn a Cycle key Page 3.10 Delete Device/Key codes 3.11 Create a Macro 3.11.1 Macro b. Re:control M207 Users Manual An Example to Add a Macro The basic devices in operation: The commands for the Macro key. The correlation table could be shown as below: 3.11.2 Timer Macro A. Create a Timer Macro Page B. Delete Your Timer Macro C. Re-label Your Timer Macro D. View Your Timer Macro 3.12 Create Your Favorite Channels 3.12.1 Add the favorite channel keys 3.12.2 Set these Macros as your favorite channels Chapter 4 Menus 4.1 Setting Page LCD Off Light Sensitivity Light Period Motion Welcome Page Calibrate 4.2 Key Layout 4.3 Code Setting 4.4 Timer Macro 4.5 Duplicate Duplicate Page 4.6 Calibrate Chapter 5 Install USB Cable and Software 5.1 Install Re:connect USB cable 5.1.1 Install the Driver Page 5.2 Install Upgrade Tools Page 5.3 Upgrade VMCU Firmware and VMCF Pre-programmed Codes Page Page Appendix A Features Re:control M207 Users Manual Specifications Appendix B Optional Accessories 72 Appendix C Troubleshooting Tables Problem Solution 73 Problem Solution